1995 NISSAN ALMERA N15 low oil pressure

PRE-DELIVERYINSPECTIONITEMS
Shown belowarePre-delivery InspectionItemsrequired forthe new vehicle. Itis recommended that
necessary itemsotherthanthose listedherebeadded, payingdueregard tothe conditions ineach
country.

Perform applicable itemsoneach model. Consult textofthis section forspecifications .

UNDER HOOD-engine off

o
Radiator coolantlevelandcoolant hosecon-
nections forleaks

o
Battery fluidlevel, specific gravityandcondi-
tions ofbattery terminals

o
Drive beltstension

D
Fuel filter forwater ordusts, andfuel lines
and connections forleaks
[] Engine oillevel andoilleaks

D
Clutch andbrake reservoir fluidlevel and
fluid lines forleaks

o
Windshield andrear window washerand
headlamp cleanerreservoir fluidlevel

D
Power steering reservoir fluidlevel andhose
connections forleaks

ON INSIDE ANDOUTSIDE

D
Remove frontspring/strut spacer(Ifapplica-
ble)

D
Operation ofall instruments, gauges,lights
and accessories

o
Operation ofhorn(s), wiperandwasher
[] Steering lockforoperation
[] Check airconditioner forgas leaks

o
Front andrear seats, andseat belts foroper-
ation

n
All moldings, trimsandfittings forfitand
alignment

[J
Allwindows foroperation andalignment

n
Hood, trunklid,door panels forfitand align-
ment

[1
Latches, keysandlocks foroperation

rl
Weatherstrips foradhesion andfit

[l
Headlamp aiming
I~ Tighten wheelnuts(Inc. inner nutsifapplica-
ble)
IJ Tire pressure (Inc.spare tire)

Il
Check frontwheels fortoe-in
IJ Install clock/voltmeter/room lampfuse(If
applicable)
~ Install deodorizing filtertoair purifier (If
applicable)
~ Remove wiperbladeprotectors (Ifapplicable)
UNDER
BODY

o
Manual transmission/transaxle, transferand
differential gearoillevel

D
Brake andfuel lines andoil/fluid reservoirs
for leaks

D
Tighten boltsandnuts ofsteering linkageand
gear box,suspension, propellershaftsand
drive shafts
~ Tighten rearbody boltsandnuts (Models with
wooden bedonly)

ROAD TEST

D
Clutch operation

D
Parking brakeoperation

[J
Service brakeoperation

D
Automatic transmission/transaxle shifttiming
and kickdown
[] Steering controlandreturnability

o
Engine performance

D
Squeaks andrattles

ENGINE OPERATING ANDHOT

D
Adjust idlemixture andspeed (andignition
timing*1)

n
Automatic transmission/transaxle fluidlevel
~ Engine idlingandstop knob operation (Diesel
only)

FINAL INSPECTION

n
Install necessary parts(outside mirror,wheel
covers, seatbelts, mat,carpet ormud flaps)

[1
Inspect forinterior andexterior metaland
paint damage
[] Check forspare tire,jack, tools (wheel
chock), andliterature

n
Wash, cleaninterior andexterior

"1: Not required onmodels withadirect ignition system
~ :Not appiicable tothis model.
•

MA-5

2/3
ofaturn
ENGINE
MAINTENANCE @Q]
Changing EngineOilFilter (Cont'd)

3. Screw oilfilter onuntil aslight resistance isfelt, then tighten
an additional 2/3turn.
4. Warm upengine andcheck oillevel.
5. Adjust oillevel ifnecessary. •

Refer toStep 4in "Changing EngineOil",MA-42.
i

• Clean excess oilfrom engine.
SMA229B Checking InjectionNozzle

1. Remove injection deliverytubesandfuel spill tube.
2. Remove nozzlewithasuitable tool[span 27mm (1.06 in)].

WARNING:
When usingnozzle tester,becareful nottoallow diesel fuel
sprayed fromnozzle tocome intocontact withyour hand or
body, andmake surethatyour eyes areproperly protected.

3. Clean andcheck nozzles.
4. Install nozzle toinjection nozzletesterandbleed airfrom
flare nut.
5. Check initialinjection pressure bypumping testerhandle
one time persecond.

EF791A
6.Install injector topressure tester.
7. Check initialinjection pressure bypumping testerhandle
slowly (onetime persecond).

Injection pressure:
12,749 kPa(127.5 bar,130kg/cm
2,
1,849psi)
• Always checkinitialinjection pressure beforeinstalling new
nozzle.

Good
\

I

,
,

I

Wrong SEF672A

8.Check fuelspray pattern bypumping testerhandle quickly
(4 or 6times persecond).
9. Ifinitial injection pressure orinjection nozzleisnot normal,
adjust orclean injection nozzleorreplace it.

Refer toEC section forinjection pressure adjustment.

10. Install allinjection nozzlesandsecurely connectfuelspill
tube anddelivery tubes.
11. Bleed airfrom fuelsystem andcheck forfuel leakage with
engine running.

EF794A
MA.43

SST491B
SST090B ON-VEHICLE
SERVICE
Bleeding Hydraulic System

1. Raise frontendofvehicle untilwheels areclear ofthe
ground.
2. Add fluid intooiltank tospecified level.Thenquickly turn
steering wheelfullytoright andleftand lightly touchsteer-
ing stoppers.
Repeat steering wheeloperation untilfluid level nolonger
decreases.
3. Start engine.
Repeat step2.above.
• Incomplete airbleeding willcause thefollowing tooccur.
When thishappens, bleedairagain.
a. Air bubbles inreservoir tank
b. Clicking noiseinoil pump
c. Excessive buzzinginoil pump
Fluid noise mayoccur inthe valve oroil pump. Thisiscommon
when thevehicle isstationary orwhile turning thesteering
wheel slowly. Thisdoes notaffect theperformance ordurabil-
ity ofthe system.

Checking SteeringWheelTurning Force(For
power steering)

1. Park vehicle onalevel, drysurface andsetparking brake.
2. Start engine.
3. Bring power steering fluiduptoadequate operating temper-
ature. [Make suretemperature offluid isapproximately 60
to 80°C (140to176°F).]

Tires needtobe inflated tonormal pressure.

4. Check steering wheelturning forcewhen steering wheel
has been turned 360°from theneutral position.

Steering wheelturning force: •
39 N(4 kg, 9Ib) orless

5.
If
steering wheelturning forceisout ofspecification, check
rack sliding force.
a. Disconnect steeringcolumnlowerjointandknuckle arms
from thegear.
b. Start andrunengine atidle tomake suresteering fluidhas
reached normaloperating temperature.
c. Pull tie-rod slowlytomove itfrom neutral position to
::l::
11.5
mm
(::l::
0.453 in)atspeed of3.5 mm (0.138 in)/s.Check that
rack sliding forceiswithin specification.

Average racksliding force:
152.0 -240.3 N(15.5 -24.5 kg,34.2 -54.0 Ib)
Maximum forcedeviation:
98 N(10 kg, 22Ib)

6.
If
rack sliding forceisnot within specification, overhaul
steering gearassembly.
7. Ifrack sliding forceisOK, inspect steering column.Referto
ST-13.

ST-7

ST27091000

.. :Direction ofoil flow Low-pressure
hose SST834-AON-VEHICLE
SERVICE
Checking Hydraulic System

Before starting, checkbelttension, drivingpulleyandtirepres-
sure. 1. Set Tool. Open shut-off valve.Thenbleed air.(See "Bleed-
ing Hydraulic System"ST-7.)
2. Run engine.

Make suretemperature offluid intank rises to60 to80°C (140
to 176°F).
WARNING:
Warm upengine withshut-off valvefullyopened. Ifengine is
started withshut-off valveclosed, fluidpressure inoil pump
increases tomaximum. Thiswillraise oiltemperature abnor-
mally.

3. Check pressure withsteering wheelfullyturned toleft and
right positions withengine idlingat1,000 rpm.

CAUTION:
Do not hold thesteering wheelinalocked position formore
than 15seconds.
Oil pump maximum standardpressure:
7,649 -8,238 kPa(76.5 .82.4 bar,
78 -84 kg/cm
2,
1,109-1,194 psi)

4.
If
oil pressure isbelow thestandard pressure, slowlyclose
shut-off valveandcheck pressure.
• When pressure reachesstandard pressure, gearisdam-
aged.
• When pressure remainsbelowstandard pressure, pumpis
damaged.

CAUTION: Do not close shut-off valveformore than15seconds.

5.
If
oil pressure ishigher thanstandard pressure, checkoil
pump flowcontrol valve.
6. After checking hydraulic system,removeToolandaddfluid
as necessary. Thencompletely bleedairout ofsystem.

S1-8