1994 JEEP CHEROKEE climate control

HEATING AND AIR CONDITIONING
CONTENTS
page page
CLIMATE CONTROL SYSTEMÐXJ VEHICLES . 22
CLIMATE CONTROL SYSTEMÐYJ VEHICLES . 37
COMPRESSOR OVERHAUL............... 17
GENERAL INFORMATION.................. 1SERVICE DIAGNOSISÐELECTRICAL........ 14
SERVICE DIAGNOSISÐMECHANICAL........ 8
TORQUE SPECIFICATIONS................ 45
GENERAL INFORMATION
INDEX
page page
A/C Operation............................ 1
Compressor Oil Level...................... 6
Pressure Gauge and Manifold Assembly........ 2
Refrigerant (R-12)......................... 1
Service Precautions........................ 2Service Valves........................... 3
System Charge........................... 5
System Discharge......................... 4
System Evacuation........................ 4
A/C OPERATION
The compressor increases the pressure and temper-
ature of the refrigerant. The heated refrigerant vapor
is then pumped into the condenser where it cools by
the air passing over the condenser fins. As the refrig-
erant cools in the condenser, it condenses into a liq-
uid. Still under high pressure, the liquid refrigerant
passes into the receiver. The receiver acts as a reser-
voir to furnish refrigerant to the expansion (H) valve
at all times. From the receiver, the high pressure liq-
uid refrigerant passes to the expansion (H) valve.
The expansion (H) valve meters refrigerant into the
evaporator where a low pressure is maintained by
the suction side of the compressor. As it enters the
evaporator, the refrigerant immediately begins to
boil by absorbing heat from the air passing over the
evaporator core. Having given up its heat to boil the
refrigerant, the air is cooled and passes into the pas-
senger compartment of the vehicle. From the evapo-
rator the vaporized refrigerant is drawn back to the
compressor to repeat the cycle.
REFRIGERANT (R-12)
It is illegal to release R-12 into the atmosphere.
SAFETY PRECAUTIONS
WARNING: EXTREME CARE MUST BE TAKEN TO
PREVENT ANY LIQUID REFRIGERANT FROM COM-
ING IN CONTACT WITH THE SKIN AND ESPE-
CIALLY THE EYES. ALWAYS WEAR SAFETYGOGGLES WHEN SERVICING ANY PART OF THE
REFRIGERANT SYSTEM. IF EYE CONTACT IS
MADE, APPLY A FEW DROPS OF MINERAL OIL TO
THE EYES AND FLUSH WITH WATER FOR SEV-
ERAL MINUTES. SEEK MEDICAL ATTENTION IMME-
DIATELY.
The refrigerant used in the air conditioner system
is Refrigerant-12 (R-12). R-12 is nonexplosive, non-
flammable, non-corrosive, has practically no odor and
is heavier than air. Although it is classified as a safe
refrigerant, certain precautions must be observed to
protect the parts involved and the person who is
working on the unit. Liquid R-12, at normal atmo-
sphere pressures and temperatures, evaporates so
quickly that it has the tendency to freeze anything it
contacts.
WARNING: TO AVOID A DANGEROUS EXPLOSION,
NEVER WELD OR STEAM CLEAN NEAR AIR CON-
DITIONING LINES OR COMPONENTS. DO NOT
HEAT R-12 ABOVE 52ÉC (125ÉF).
The R-12 in the system is always under pressure.
Because the system is tightly sealed, heat applied to
any part could cause this pressure to build up exces-
sively.
JHEATING AND AIR CONDITIONING 24 - 1

CLIMATE CONTROL SYSTEMÐXJ VEHICLES
INDEX
page page
A/C Recirculating Air Door Vacuum Motor
Replacement.......................... 31
Blower Motor Resistors Replacement......... 35
Blower Motor/Fan Replacement.............. 26
CondenserÐ4.0L Engines.................. 32
Condenser/Receiver DrierÐ2.5L Engines....... 31
Defroster Duct Replacement................ 29
Description............................. 22
Evaporator Coil.......................... 34
Evaporator/Blower Housing................. 33Expansion (H) Valve...................... 35
Heater and A/C Control Panel Replacement.... 26
Heater Control Cable Replacement........... 30
Heater Core............................ 28
Heater Core Housing Replacement........... 29
Heater/Defroster/Instrument Panel Outlet Door
Vacuum Motor Replacement............... 30
Receiver DrierÐ4.0L Engines............... 32
Temperature Control Thermostat............. 35
DESCRIPTION
The Climate Control System combines air condi-
tioning, heating and ventilating capabilities for vehi-
cles equipped with air conditioning. Vehicles without
air conditioning perform heating and ventilating
functions without the air conditioning evaporator.
Both systems consist basically of 2 parts:
²Blower and Air Inlet Assembly
²Heater Core and Air Distribution Assembly
These assemblies, initially installed as a single
unit, may be removed separately from under the in-
strument panel as required for service.
HEATER SYSTEM
The heater system is a blend air type. Outside air
is heated and then blended in varying amounts with
cooler outside air to obtain the desired discharge
temperature. A heater coolant valve provides full
flow to the heater core for all heating modes. The
heater coolant valve remains closed for the ventila-
tion mode, allowing discharge air to approach the
outside ambient air temperature.
AIR CONDITIONING SYSTEM
The air conditioning system has an evaporator to
cool and dehumidify the incoming outside air prior to
blending with the heated air. The evaporator is in
operation during the A/C mode and also in the de-
frost mode for defogging purposes. The evaporator is
not in operation at ambient temperatures below ap-
proximately -1ÉC (30ÉF). To maintain minimum evap-
orator temperature, a fixed thermostat setting switch
cycles the compressor clutch. The blower is operatingthe heater or air conditioning systems, except the
OFF mode. In this mode (OFF) the blower and the
outside air are shut off.
The cooling unit is mounted on the dash panel and
the cooled air is discharged from the instrument
panel registers. The registers are adjusted to provide
general or localized cooling.
SIGHT GLASS
The sight glass is located on top of the receiver/
drier. The sight glass provides a visual check of the
system refrigerant level. A continuous stream of bub-
bles will appear in the sight glass when the system
charge is low. Bubbles will not appear when the sys-
tem is fully charged.
LOW PRESSURE SWITCH
The low pressure switch disengages the magnetic
clutch if the pressure in the system drops below 193
kPa (28 psi). This will occur with a loss in refriger-
ant or with cold ambient temperature.
HEATER VALVE
The heater valve regulates coolant flow to the
heater core. It requires vacuum to shut off flow to
the heater core.
These vehicles are equipped with a bypass-type
heater water valve. When the heater valve is closed,
coolant flow to the heater core is bypassed back to
the engine. When the heater valve is open, coolant is
directed through the heater core and back to the en-
gine.
24 - 22 HEATING AND AIR CONDITIONINGJ

CLIMATE CONTROL SYSTEMÐYJ VEHICLES
INDEX
page page
A/C Blower Motor........................ 43
A/C Condenser.......................... 42
A/C Control Panel........................ 41
Blower Motor (Heating).................... 40
Blower Motor/Air Door Motor Switch Replacement . 39
Defroster Nozzle and Duct................. 40
Description (Air Conditioning)................ 41
Description (Heating)...................... 37
Evaporator and Housing................... 42
Expansion (H) Valve...................... 43Fresh Air Door Vacuum Motor............... 41
Fresh Air Intake Duct..................... 41
Fresh Air Ventilation...................... 39
Heater Control Panel Replacement........... 39
Heater Core and Housing.................. 40
Heater/Defroster Operation................. 37
Receiver-Drier Replacement................ 42
Sight Glass............................. 41
Vent Door Control Cables.................. 39
DESCRIPTION (HEATING)
A blend-air heating system is used in YJ vehicles.
The blend-air system provides a constant flow of en-
gine coolant through the heater core.
The temperature of heated air entering the passen-
ger compartment is controlled by regulating the
quantity of air flow through the heater core. This is
accomplished by blending a controlled amount of un-
heated air from outside the vehicle with heated air
from the heater core.
HEATER/DEFROSTER OPERATION
The heater core is connected to the engine cooling
system. It operates on the circulation of heated en-
gine coolant through the core and a supply of fresh
air drawn in through the intake grille on the cowl.
Engine coolant flows through the heater core at all
times.
The heater controls are on the heater control panel
(Fig. 1).
The air control lever (Fig. 1) operates a door in the
fresh air intake duct. The door controls the amount
of fresh air flow into the heater housing and core.
When the lever is in the OFF position, the intake
door is closed preventing air flow into the housing.The temperature control lever (Fig. 1) determines
air flow through the heater core. The lever operates
the heater housing blend-air door which controls air
flow through the core.
The blower motor is operated by the control switch
(Fig. 1). The switch provides 3 blower speeds for in-
creased air flow in heat or defrost mode.
HEATING
Maximum air flow and heater output occurs when
the air control lever is in HEAT position and the
temperature control lever is in WARM position. The
blend-air door is closed and all intake air is directed
through the heater core in this operating mode (Fig.
2).
Temperature regulation of the heated air is deter-
mined by position of the temperature control lever.
Moving the control lever from WARM to an in-be-
tween position, opens the blend-air door in the heater
housing. As the door opens, unheated outside air is
drawn into the system and blended with heated air
from the core.
DEFROSTING
The heater housing contains a defroster door to di-
vert heated air to the defroster duct and windshield
outlets (Fig. 2). Defrost air flow is controlled by the
air control lever.
For defroster operation, the air control lever must
be moved to the defrost detent. The detent is identi-
fied by the defrost symbol on the control panel. In
this position, the defroster door in the heater housing
diverts all heated air (from the core) to the defroster
duct windshield outlets.
If the air control lever is moved to any position be-
tween the heat and defrost detents, the defroster door
does not close completely. In this mode, the door re-
mains partially open causing heated air to be divided
equally between the heat and defrost outlets.
Fig. 1 Heater Control Panel
JHEATING AND AIR CONDITIONING 24 - 37

CARPET/FLOOR MATS.................23-198
CARPET/MATÐXJ VEHICLES, FRONT.....23-129
CARPET/MATÐXJ VEHICLES, REAR......23-130
CARPETS AND FLOOR MATS............23-129
CARRIER, EXTERNAL SPARE/WHEEL
TIRE..............................23-172
CASE ASSEMBLY, TRANSFER......21-282,21-306
CASE CLEANING AND INSPECTION,
TRANSMISSION.....................21-118
CASE COVER OIL SEAL REPLACEMENT,
TIMING.........................9-26,9-67
CASE COVER, TIMING...............9-27,9-67
CASE DISASSEMBLY AND OVERHAUL,
TRANSFER...................21-277,21-297
CASE FILL LEVEL, TRANSFER...........21-294
CASE IDENTIFICATION, ENGINE AND
TRANSMISSION/TRANSFER..........INTRO.-3
CASE IDENTIFICATION, TRANSFER . 21-273,21-293
CASE INSTALLATION, TRANSFER . . . 21-276,21-296
CASE, LEGEND FOR NP231 TRANSFER....21-292
CASE, LEGEND FOR NP242 TRANSFER....21-319
CASE LUBRICANT, TRANSFER.....21-273,21-294
CASE, NP231 TRANSFER.........21-272,21-291
CASE, NP242 TRANSFER...............21-293
CASE OVERHAUL, FIRST-REVERSE
BRAKE PISTON AND TRANSMISSION....21-237
CASE REMOVAL, TRANSFER......21-276,21-296
CASE SPECIFICATIONS, TRANSMISSION/
TRANSFER.........................21-320
CASE, TRANSFER.......................0-25
CATALYTIC CONVERTER..............11-1,11-5
CATALYTIC CONVERTER/MUFFLER/
TAILPIPE SUPPORT BRACKETS.........23-85
CAUSES, CLUTCH PROBLEM...............6-3
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐXJ.......................8L-10
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐYJ.......................8L-11
CERTIFICATION LABEL, VEHICLE SAFETY . INTRO.-1
CHAIN AND SPROCKETS, TIMING......9-28,9-68
CHANGE AND FILTER REPLACEMENT,
ENGINE OIL..........................0-15
CHANGE, LUBRICANT; FRONT
SUSPENSION AND AXLE................2-22
CHANGE, LUBRICANT; REAR SUSPENSION
AND AXLES......................3-13,3-30
CHARGE RATE.........................8A-6
CHARGE, SYSTEM......................24-5
CHARGING, BATTERY....................8A-5
CHARGING TIME TABLE, BATTERY.........8A-5
CHASSIS AND BODY COMPONENTS........0-30
CHASSIS COMPONENT AND WHEEL
BEARING LUBRICANTS.................0-30
CHECK BALL DIMENSIONS, AW-4 VALVE
BODY.............................21-328
CHECK ENGINE LAMP FOR DIAGNOSTIC
TROUBLE CODES, INDICATOR..........8A-19
CHECK ENGINE, MALFUNCTION
INDICATOR LAMP; INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
CHECK ENGINE, MALFUNCTION
INDICATOR LAMP; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
CHECK, PRELIMINARY BRAKE..............5-7
CHECK (ROAD TEST), OPERATIONAL.......8H-7
CHECK VALVE REPLACEMENT............19-33
CHECK VALVE TEST, POWER BOOSTER......5-11
CHECK WITH BATTERY INDICATOR
(BASE CLUSTER ONLY), OPERATIONAL . . . 8A-14
CHECK WITH VOLTMETER, OPERATIONAL . . . 8A-15
CHECKING FLUID LEVEL AND
CONDITION...................21-96,21-173
CHECKING FOR DIAGNOSTIC TROUBLE
CODE...............................8H-5
CHECKS FIRST, SYMPTOM AND ACTIONÐ
SEE PRELIMINARY.....................7-6
CHECKS, PRELIMINARY...................7-5
CHIP PROTECTION, STONE.............23-201
CHMSLÐXJ, CENTER HIGH MOUNTED
STOP LAMP.........................8L-10
CHMSLÐYJ, CENTER HIGH MOUNTED
STOP LAMP
.........................8L-11
CIRCUIT DIAGNOSIS, IGNITION
SECONDARY
........................8D-12
CIRCUIT IDENTIFICATION
................8W-2
CIRCUIT, PRINTED
.....................8E-22CIRCUIT REMOVAL, PRINTED............8E-24
CIRCUIT REPLACEMENT, PRINTED........8E-19
CIRCUIT REPLACEMENTÐINSTRUMENT
CLUSTER REMOVED, PRINTED...........8E-6
CIRCUIT SENSEÐPCM INPUT, IGNITION....14-21
CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER FEED..............8A-9
CIRCUIT TESTS, STARTER CONTROL......8A-11
CIRCUIT VOLTAGE, BATTERY OPEN.........8A-4
CIRCUIT VOLTAGE TEST, BATTERY OPEN....8A-3
CIRCUITS, ABS SYSTEM WIRING AND
ELECTRICAL..........................5-4
CLAMPS, FUEL TUBES/LINES/HOSES . . 14-9,14-56
CLASSIFICATION OF LUBRICANTS...........0-2
CLASSIFICATIONS AND RATINGS,
BATTERY............................8A-8
CLASSIFICATIONS AND RATINGSÐ
LEFT HAND DRIVE, BATTERY...........8B-10
CLASSIFICATIONS AND RATINGSÐ
RIGHT HAND DRIVE, BATTERY..........8B-10
CLEAN BRAKE FLUID, IMPORTANCE OF.....5-48
CLEANER, AIR.........................25-7
CLEANER FILTER ELEMENT, ENGINE AIR....0-16
CLEANER HOUSING, AIR; EMISSION
CONTROL SYSTEMS...................25-8
CLEANER HOUSING, AIR; FUEL SYSTEM....14-54
CLEANING AND INSPECTION . 21-13,21-204,21-305
CLEANING AND INSPECTION, CALIPER......5-28
CLEANING AND INSPECTION, GEAR.......19-40
CLEANING AND INSPECTION,
TRANSMISSION CASE................21-118
CLEANING OF TIRES....................22-2
CLEANING/INSPECTION; FRONT
SUSPENSION AND AXLE................2-35
CLEANING/INSPECTION; REAR
SUSPENSION AND AXLES...............3-18
CLEANING/REVERSE FLUSHING,
COOLING SYSTEM....................7-17
CLEARANCE, AW-4 BUSHING AND
PISTON...........................21-326
CLIMATE CONTROL SYSTEMÐXJ VEHICLES . 24-22
CLIMATE CONTROL SYSTEMÐYJ VEHICLES . 24-37
CLIP, FUEL AND BRAKE FLUID TUBE
RETAINER; BODY COMPONENTSÐXJ
VEHICLES..........................23-86
CLIP, FUEL AND BRAKE FLUID TUBE
RETAINER; FRAME AND BUMPERS.......13-16
CLUSTER AND GAUGE HOUSINGS,
INSTRUMENT......................23-190
CLUSTER BEZEL, INSTRUMENT.....23-91,23-191
CLUSTER BULB REPLACEMENT,
INSTRUMENT.......................8E-19
CLUSTER DIAGNOSIS, INSTRUMENT;
INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-3
CLUSTER DIAGNOSIS, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-14
CLUSTER GAUGES, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐXJ . . 8E-13
CLUSTER GAUGES, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-27
CLUSTER GENERAL INFORMATION,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-1
CLUSTER GENERAL INFORMATION,
INSTRUMENT; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-14
CLUSTER, HIGH LINE...................8E-12
CLUSTER, INSTRUMENT................8E-15
CLUSTER, LOW LINE...................8E-11
CLUSTER REMOVED, GAUGE
REPLACEMENTÐINSTRUMENT..........8E-5
CLUSTER REMOVED, GEAR SELECTOR
INDICATOR REPLACEMENTÐ
INSTRUMENT........................8E-6
CLUSTER REMOVED, PRINTED CIRCUIT
REPLACEMENTÐINSTRUMENT..........8E-6
CLUSTER REMOVED, SPEEDOMETER
REPLACEMENTÐINSTRUMENT..........8E-5
CLUSTER REMOVED, TACHOMETER
REPLACEMENTÐINSTRUMENT
..........8E-5
CLUSTER REPLACEMENT, GAUGE
.........8E-24
CLUSTER REPLACEMENT, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐXJ
. . . 8E-5
CLUSTER REPLACEMENT, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ
. . 8E-17CLUSTER SERVICE PROCEDURES,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-5
CLUSTER SERVICE PROCEDURES,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐYJ........................8E-17
CLUSTER/SWITCH/LIGHTER/RADIO/HEVAC,
INSTRUMENT.......................23-91
CLUSTERS, INSTRUMENT...............8E-10
CLUTCH AND BRAKE PACK
REQUIREMENTS, AW-4...............21-328
CLUTCH AND OUTPUT SHAFT
OVERHAUL, NO. 2 ONE-WAY..........21-234
CLUTCH COMPONENT LUBRICATION.........6-1
CLUTCH COMPONENTS
...................6-1
CLUTCH COVER AND DISC INSTALLATION
....6-10
CLUTCH COVER AND DISC REMOVAL
.......6-10
CLUTCH DIAGNOSIS
.....................6-3
CLUTCH DISC AND PLATE THICKNESS,
AW-4
.............................21-325
CLUTCH FLUID LEVEL
...................6-14
CLUTCH HOUSING REPLACEMENT
.........6-11
CLUTCH, HYDRAULIC
....................0-22
CLUTCH HYDRAULIC LINKAGE
INSTALLATION
........................6-12
CLUTCH HYDRAULIC LINKAGE REMOVAL
....6-11
CLUTCH INSPECTION, TORQUE
CONVERTER STATOR
................21-189
CLUTCH LINKAGE FLUID
..................6-1
CLUTCH, MAGNETIC
....................24-18
CLUTCH OPERATION
.....................6-2
CLUTCH OVERHAUL, DIRECT
............21-219
CLUTCH OVERHAUL, FORWARD
.........21-223
CLUTCH OVERHAUL, FRONT
............21-125
CLUTCH OVERHAUL, OVERDRIVE
PLANETARY GEAR
...................21-209
CLUTCH OVERHAUL, REAR
.............21-128
CLUTCH OVERHAUL, SUN GEAR AND
NO. 1ONE-WAY
.....................21-229
CLUTCH PEDAL INSTALLATION
............6-15
CLUTCH PEDAL REMOVAL
................6-15
CLUTCH PROBLEM CAUSES
...............6-3
CLUTCH RELAY, AIR CONDITIONING
.......14-54
CLUTCH RELAYÐPCM OUTPUT, AIR
CONDITIONING
......................14-24
CLUTCH RELAYÐPCM OUTPUT, TORQUE
CONVERTER
........................14-27
CLUTCH RELAY TEST, TORQUE
CONVERTER
........................14-45
CLUTCH RELAY, TORQUE CONVERTER
.....14-60
CLUTCH SAFETY PRECAUTIONS
...........6-10
CLUTCH SERVICE
.......................6-10
CLUTCHÐLOW-REVERSE DRUMÐREAR
SUPPORT OVERHAUL, OVERRUNNING
. . . 21-118
COAT, BASE/COLOR
...................23-201
CODE, CHECKING FOR DIAGNOSTIC
TROUBLE
...........................8H-5
CODE DECODING, VEHICLE
...........INTRO.-3
CODE (DTC), DIAGNOSTIC TROUBLE
.......14-51
CODE (DTC), GENERATOR DIAGNOSTIC
TROUBLE
...........................8A-19
CODE IDENTIFICATION, WIRE
.............8W-2
CODE LETTERS, JEEP BODY
...............5-2
CODE PLATE, VEHICLE
...............INTRO.-2
CODES AND DIMENSIONS,
DESIGNATIONS, LABELS/PLATES,
.....INTRO.-1
CODES, INDICATOR (CHECK ENGINE)
LAMP FOR DIAGNOSTIC TROUBLE
.......8A-19
CODES, VEHICLE DESIGNATION
........INTRO.-1
CODES, XJ EXTERIOR PAINT
............23-205
CODES, XJ INTERIOR PAINT
............23-205
CODES, YJ EXTERIOR PAINT
............23-206
CODES, YJ INTERIOR PAINT
............23-206
COIL, EVAPORATOR
....................24-34
COIL, IGNITION; FUEL SYSTEM
...........14-57
COIL, IGNITION; IGNITION SYSTEMS
. 8D-4,8D-11,
8D-26
COILÐPCM OUTPUT, IGNITION
...........14-26
COIL RESISTANCE, IGNITION
............8D-11
COIL SPRING
..........................2-13
4 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

COLD CRANKING TEST, STARTING
SYSTEM............................8A-9
COLLISION DAMAGE TORQUE.............13-1
COLORS, EXTERIOR BODY..............23-204
COLUMN GENERAL SERVICE, STEERING . . . 19-45
COLUMN, NON-TILT STEERING...........19-50
COLUMN REPLACEMENTÐXJ............19-46
COLUMN REPLACEMENTÐYJ............19-48
COLUMN, TILT STEERING...............19-59
COLUMNÐXJ, STEERING...............19-73
COLUMNÐYJ, STEERING...............19-73
COMBINATION VALVE................5-15,5-42
COMBINATION VALVE REPLACEMENTÐXJ . . . 5-55
COMBINATION VALVE REPLACEMENTÐYJ . . . 5-55
COMBUSTION PRESSURE LEAKAGE
TEST, CYLINDER.......................9-6
COMBUSTION PRESSURE LEAKAGE
TEST DIAGNOSIS, CYLINDER.............9-6
COMPASS REPAIR PROCEDURES..........8C-4
COMPENSATION, CALIPER OPERATION
AND WEAR..........................5-24
COMPRESSION PRESSURE TEST,
CYLINDER............................9-5
COMPRESSOR........................24-17
COMPRESSOR DIAGNOSIS..............24-13
COMPRESSOR ISOLATION...............24-17
COMPRESSOR OF AIR, PURGING.........24-17
COMPRESSOR OIL LEVEL................24-6
COMPRESSOR OVERHAUL...............24-17
COMPRESSOR VALVE PLATEÐLEAK
TESTS..............................24-8
COMPRESSOR/HOSES/FITTINGS, AIR-
CONDITIONER........................0-21
CONDENSERÐ4.0L ENGINES............24-32
CONDENSER, A/C......................24-42
CONDENSER/RECEIVER DRIERÐ2.5L
ENGINES...........................24-31
CONDITION, CHECKING FLUID LEVEL......21-96,
21-173
CONDITION, FLUID LEVEL...............21-69
CONDITIONING CLUTCH RELAY, AIR.......14-54
CONDITIONING CLUTCH RELAYÐPCM
OUTPUT, AIR........................14-24
CONDITIONING CONTROLSÐPCM INPUT,
AIR ...............................14-19
CONDITIONING SCHEMATIC, AIR..........24-25
CONDITIONING SYSTEM DIAGNOSIS,
AIR ...............................24-12
CONDITIONING SYSTEMÐXJ VEHICLES,
AIR ...............................24-14
CONDITIONING SYSTEMÐYJ VEHICLES,
AIR ...............................24-15
CONNECTING ROD BEARING FITTING
CHART..........................9-36,9-76
CONNECTING RODS, PISTONS........9-34,9-74
CONNECTIONS, STARTER RELAY..........8A-12
CONNECTOR AND TERMINAL ASSEMBLY
REPLACEMENT.......................8W-5
CONNECTORÐPCM INPUT, DATA LINK.....14-20
CONNECTORÐPCM OUTPUT, DATA LINK . . . 14-24
CONNECTOR PINS, RADIO................8F-3
CONNECTOR, POWERTRAIN CONTROL
MODULE (PCM) 60-WAY...............14-38
CONNECTOR REPLACEMENT.............8W-4
CONNECTORS.........................8W-3
CONSOLE, OVERHEAD...................8A-1
CONSOLE REPAIR PROCEDURES..........8C-6
CONSOLE SHIFT, DISASSEMBLYÐ
COLUMN OR
........................19-50
CONSOLEÐXJ VEHICLES, FULL FLOOR
. . . 23-125
CONSOLEÐXJ VEHICLES, MINI-FLOOR
....23-124
CONSOLEÐXJ VEHICLES, OVERHEAD
......8L-20
CONSOLES, FLOOR
...................23-197
CONSTRUCTION, XJ UNIBODY
.............13-1
CONTACT PATTERN ANALYSIS,
BACKLASH AND; FRONT SUSPENSION
AND AXLE
...........................2-44
CONTACT PATTERN ANALYSIS, BACKLASH
AND; REAR SUSPENSION AND AXLES
.....3-25
CONTAMINATION, BRAKE FLUID
...........5-13
CONTINUITY TESTS, IGNITION SWITCH
....8D-31
CONTROL AND DISPLAY SYMBOLS,
INTERNATIONAL VEHICLE
...........INTRO.-3
CONTROL AND DISPLAY SYMBOLS,
VEHICLE
.........................INTRO.-7CONTROL CABLE REPLACEMENT,
HEATER ............................24-30
CONTROL CABLES, VENT DOOR..........24-39
CONTROL CIRCUIT TESTS, STARTER......8A-11
CONTROL, FUEL PUMP ELECTRICAL........14-5
CONTROL (IAC) MOTOR, IDLE AIR........14-56
CONTROL (IAC) MOTORÐPCM OUTPUT,
IDLE AIR...........................14-25
CONTROL INFORMATION (VECI)
LABEL, VEHICLE WINDOW..............25-1
CONTROL MODULE, ELECTRICAL TESTS
AT POWERTRAIN.....................8H-6
CONTROL MODULE (PCM) 60-WAY
CONNECTOR, POWERTRAIN............14-38
CONTROL MODULE (PCM), POWERTRAIN;
EMISSION CONTROL SYSTEMS..........25-9
CONTROL MODULE (PCM), POWERTRAIN;
FUEL SYSTEM..................14-18,14-58
CONTROL MODULE (PCM), POWERTRAIN;
IGNITION SYSTEMS.........8D-6,8D-15,8D-28
CONTROL MODULE (TCM) SERVICE,
TRANSMISSION.....................21-173
CONTROL MOTOR TEST, IDLE AIR........14-46
CONTROL PANEL, A/C..................24-41
CONTROL PANEL REPLACEMENT,
HEATER ............................24-39
CONTROL PANEL REPLACEMENT,
HEATER AND A/C ....................24-26
CONTROLÐPCM INPUT, SPEED..........14-23
CONTROLÐPCM OUTPUT, SPEED.........14-27
CONTROL SERVO REPLACEMENT, SPEED....8H-9
CONTROL SWITCH REPLACEMENT,
SPEED..............................8H-9
CONTROL SWITCH REPLACEMENT,
WIPER.............................8K-15
CONTROL SWITCH TEST, STOP LAMP
SPEED..............................8H-7
CONTROL SWITCH (TURN SIGNAL
LEVER) TEST, SPEED..................8H-7
CONTROL SYSTEM ELECTRICAL TESTS,
VEHICLE SPEED......................8H-5
CONTROL SYSTEM, EVAP (EVAPORATION)....25-4
CONTROL SYSTEM, VEHICLE SPEED........8A-1
CONTROL SYSTEMÐXJ VEHICLES,
CLIMATE...........................24-22
CONTROL SYSTEMÐYJ VEHICLES,
CLIMATE...........................24-37
CONTROL THERMOSTAT, TEMPERATURE....24-35
CONTROL UNIT (ECU), ELECTRONIC........5-41
CONTROL UNIT (HCU), HYDRAULIC........5-39
CONTROL VALVE FITTING O-RING SEAL,
FLOW..............................19-12
CONTROLS AND COMPONENTS,
TRANSMISSION......................21-66
CONTROLS, EVAPORATIVE EMISSION.......25-4
CONTROLS, EXHAUST EMISSION..........25-7
CONTROLSÐPCM INPUT, AIR
CONDITIONING (A/C)..................14-19
CONTROLSÐXJ VEHICLES, BLOWER......24-14
CONVERSION FORMULAS AND
EQUIVALENT VALUES..............INTRO.-8
CONVERSION, TORQUE..............INTRO.-10
CONVERTER, CATALYTIC.............11-1,11-5
CONVERTER CLUTCH ENGAGED,
HYDRAULIC FLOW IN THIRD GEAR......21-90
CONVERTER CLUTCH RELAY.............14-60
CONVERTER CLUTCH RELAY TEST........14-45
CONVERTER CLUTCH RELAYÐPCM
OUTPUT............................14-27
CONVERTER HOUSING LEAK
DIAGNOSIS.........................21-73
CONVERTER INSTALLATION,
TRANSMISSION.....................21-109
CONVERTER INSTALLATION,
TRANSMISSION AND TORQUE.........21-190
CONVERTERÐPUMP SEALÐDRIVE
PLATE SERVICE.....................21-109
CONVERTER REMOVAL, TRANSMISSION . . . 21-108
CONVERTER REMOVAL, TRANSMISSION
AND TORQUE......................21-189
CONVERTER STALL TEST
................21-72
CONVERTER STALL TEST, TORQUE
.......21-169
CONVERTER STATOR CLUTCH
INSPECTION, TORQUE
................21-189
CONVERTER, TORQUE; TRANSMISSION
AND TRANSFER CASE
...........21-66,21-158CONVERTER/MUFFLER/TAILPIPE
SUPPORT BRACKETS, CATALYTIC........23-85
COOLANT.............................7-15
COOLANT RESERVE/OVERFLOW
SYSTEM............................7-19
COOLANT ROUTING, SYSTEM..............7-1
COOLANT TEMPERATURE GAUGE..........8E-1
COOLANT TEMPERATURE GAUGE
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
LAMP...............................8E-1
COOLANT TEMPERATURE SENSOR.........25-9
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL SYSTEM................14-55
COOLANT TEMPERATURE SENSOR,
ENGINE; IGNITION SYSTEMS
.......8D-4,8D-22
COOLANT TEMPERATURE SENSORÐ
PCM INPUT, ENGINE
..................14-21
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; FUEL SYSTEM
................14-43
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; IGNITION SYSTEMS
...........8D-12
COOLER FLOW TESTING, TRANSMISSION
. . 21-106
COOLER LINE FITTINGS, TRANSMISSION
. . 21-187
COOLER LINES AND FITTINGS,
SERVICING TRANSMISSION
...........21-106
COOLER REVERSE FLUSHING,
TRANSMISSION
.....................21-105
COOLER SERVICE, TRANSMISSION
.......21-187
COOLERS, TRANSMISSION OIL
............7-29
COOLING SYSTEM; COOLING SYSTEM
.......7-1
COOLING SYSTEM; LUBRICATION AND
MAINTENANCE
.......................0-16
COOLING SYSTEM CAPACITIES
............7-38
COOLING SYSTEM CLEANING/REVERSE
FLUSHING
...........................7-17
COOLING SYSTEM COMPONENTS
...........7-1
COOLING SYSTEM, DRAINING
.............7-16
COOLING SYSTEM FANS
.................7-26
COOLING SYSTEM FOR LEAKS, TESTING
....7-18
COOLING SYSTEM HOSES
................7-26
COOLING SYSTEM, REFILLING
............7-17
CORE AND HOUSING, HEATER
............24-40
CORE, HEATER
........................24-28
CORE HOUSING REPLACEMENT, HEATER
. . . 24-29
COVER AND DISC INSTALLATION,
CLUTCH
.............................6-10
COVER AND DISC REMOVAL, CLUTCH
......6-10
COVER AND FRAME, BUCKET SEATBACK
. . 23-100
COVER, BUCKET SEAT CUSHION
..........23-98
COVER, ENGINE CYLINDER HEAD
......9-18,9-59
COVER, FRAME CROSSMEMBER
..........13-14
COVER OIL SEAL REPLACEMENT,
TIMING CASE
....................9-26,9-67
COVER REPLACEMENT, PITMAN SHAFT
AND SIDE
..........................19-26
COVER, TIMING CASE
...............9-27,9-67
COVERÐXJ VEHICLES, REAR SEAT
CUSHION
..........................23-107
COVERÐXJ VEHICLES, REAR
SEATBACK
.........................23-111
COVERSÐXJ VEHICLES, B/C-PILLAR AND
LIFTGATE PILLAR TRIM
..............23-116
COWL GRILLE AND SCREEN
.......23-11,23-139
COWL WEATHERSTRIP SEAL
............23-139
COWL WEATHERSTRIP SEAL/
CROSSMEMBER AIR DEFLECTOR
........23-10
CRANKCASE VENTILATION SYSTEM;
EMISSION CONTROL SYSTEMS
..........25-5
CRANKCASE VENTILATION SYSTEM;
LUBRICATION AND MAINTENANCE
........0-17
CRANKING TEST, STARTING SYSTEM
COLD
...............................8A-9
CRANKSHAFT MAIN BEARINGS;
ENGINES
........................9-40,9-80
CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM
.......................14-55
CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS
..............8D-2,8D-21
JINDEX5
Description Group-Page Description Group-Page Description Group-Page

STRAP, FUEL TANK SUPPORT............23-86
STRIKER AND BUMPERÐXJ VEHICLES,
REAR SEATBACK LATCH..............23-111
STRIKER, HALF-METAL DOOR LATCH.....23-175
STRIKER REPLACEMENT, HOOD LATCH....23-10
STRIKER REPLACEMENT, SAFETY LATCH . . . 23-10
STRIKER, TAILGATE LATCH.............23-161
STRIP, DOOR EDGE GUARD/EDGE
PROTECTOR........................23-61
STRIPES/DECALS, BODY..........23-25,23-153
STUD REPLACEMENT, LIFTGATE SUPPORT
ROD BALL..........................23-70
STUDS, STEERING KNUCKLE AND BALL.....2-30
STUDS, STEERING LINKAGE AND BALL.....0-30
SUN GEAR AND NO. 1 ONE-WAY
CLUTCH OVERHAUL.................21-229
SUNVISORS...................23-124,23-196
SUPPORT BRACKET, I/P TWEETER
SPEAKER/COURTESY LAMP............23-95
SUPPORT BRACKET REPLACEMENT,
INTERIOR REARVIEW MIRROR..........23-75
SUPPORT BRACKETS, CATALYTIC
CONVERTER/MUFFLER/TAILPIPE.........23-85
SUPPORT CUSHION, ENGINE FRONT.......13-15
SUPPORT OVERHAUL, OVERDRIVE.......21-216
SUPPORT OVERHAUL, OVERRUNNING
CLUTCHÐLOW-REVERSE DRUMÐ
REAR.............................21-118
SUPPORT PLATE REPLACEMENT...........5-37
SUPPORT ROD BALL STUD
REPLACEMENT, LIFTGATE..............23-70
SUPPORT ROD CYLINDER DISPOSAL,
LIFTGATE...........................23-70
SUPPORT ROD CYLINDER, LIFTGATE......23-69
SUPPORT STRAP, FUEL TANK............23-86
SUPPORTS, ENGINE (MOUNTS)............0-20
SURFACE PREPARATION...............23-201
SUSPENSION, REAR.....................3-1
SUSPENSION AND STEERING SYSTEM
DIAGNOSIS...........................2-7
SUSPENSION ARM, LOWER...............2-11
SUSPENSION ARM, UPPER...............2-11
SUSPENSION COMPONENTS, XJ FRONT.....2-47
SUSPENSION COMPONENTS, XJ REAR......3-50
SUSPENSION COMPONENTS, YJ FRONT.....2-47
SUSPENSION COMPONENTS, YJ REAR......3-50
SUSPENSION, FRONT............2-1,2-10,2-13
SUSPENSION, REAR..................2-1,3-5
SWITCHÐ2.5L ENGINE ONLY, POWER
STEERING PRESSURE.................14-58
SWITCH, ACCELERATION.................5-41
SWITCH ADJUSTMENT, BRAKELIGHT.......5-66
SWITCH AND PLUG LOCATIONS,
TRANSMISSION......................21-33
SWITCH, BRAKE.......................14-54
SWITCH, BRAKE PEDAL AND BRAKELIGHT....5-65
SWITCH CONTINUITY TESTS, IGNITION....8D-31
SWITCHÐDRIVERS DOOR POWER LOCK . . . 8P-2,
8P-3,8P-4
SWITCHÐDRIVERS DOOR POWER
WINDOW...................8S-5,8S-6,8S-7
SWITCH (HORN PAD) REPLACEMENT, HORN . 8G-3
SWITCH, IGNITION; BRAKES..............5-42
SWITCH, IGNITION; IGNITION SYSTEMS....8D-30
SWITCH INSTALLATION, BRAKELIGHT.......5-66
SWITCH INSTALLATION/ADJUSTMENT,
IGNITION...........................8D-31
SWITCH OPERATION, ACCELERATION.......5-45
SWITCH, OVERDRIVE (OVERRIDE)........14-22
SWITCH, PARK/NEUTRAL POSITION . . 8B-6,14-58,
21-173
SWITCH, PASSENGER DOOR LOCK.........8P-5
SWITCH, PASSENGER DOOR WINDOW......8S-8
SWITCHÐPCM INPUT, BRAKE............14-20
SWITCHÐPCM INPUT, EXTENDED IDLE....14-21
SWITCHÐPCM INPUT, PARK/NEUTRAL.....14-22
SWITCHÐPCM INPUT, POWER
STEERING PRESSURE.................14-22
SWITCH, POWER MIRROR................8T-2
SWITCH REMOVAL, BRAKELIGHT..........5-66
SWITCH REMOVAL, IGNITION
............8D-30
SWITCH REPLACEMENT - ALL MODELS,
TURN/HAZARD
........................8J-3
SWITCH REPLACEMENT, BLOWER
MOTOR/AIR DOOR MOTOR
.............24-39
SWITCH REPLACEMENT, FOG LAMP
.......8L-14SWITCH REPLACEMENT, HEADLAMP.......8L-4
SWITCH REPLACEMENT, HEADLAMP
DIMMER............................8L-6
SWITCH REPLACEMENT, IGNITION
KEY WARNING.......................8U-4
SWITCH REPLACEMENT, LIFTGATE WIPER . . . 8K-6
SWITCH REPLACEMENT, POWER MIRROR . . . 8T-4
SWITCH REPLACEMENT, REAR WINDOW
DEFOGGER..........................8N-4
SWITCH REPLACEMENT, REAR WIPER.....8K-13
SWITCH REPLACEMENT, SPEED CONTROL . . . 8H-9
SWITCH REPLACEMENT, WIPER CONTROL . . 8K-15
SWITCH SERVICE, PARK/NEUTRAL
POSITION.........................21-103
SWITCH TEST, EXTENDED IDLE...........14-45
SWITCH TEST, STOP LAMP SPEED
CONTROL...........................8H-7
SWITCH TESTING; POWER SEATS.........8R-2
SWITCH TESTING; POWER WINDOWS......8S-5
SWITCH TESTING; REAR WINDOW
DEFOGGER..........................8N-2
SWITCH TESTING, IGNITION.............8D-30
SWITCH TESTING, POWER MIRROR........8T-2
SWITCH TESTING, REAR WIPER/
WASHER.......................8K-7,8K-14
SWITCH TESTING, WIPER...............8K-19
SWITCH (TURN SIGNAL LEVER) TEST,
SPEED CONTROL.....................8H-7
SWITCHES, REAR DEFOGGER/FOG LAMP/
REAR WIPER........................8E-21
SWITCH/ILLUMINATION RHEOSTAT,
HEADLAMP.........................8E-21
SYMBOLS, FUSES AND ABBREVIATIONS,
WIRING............................8W-6
SYMBOLS, INTERNATIONAL VEHICLE
CONTROL AND DISPLAY............INTRO.-3
SYMBOLS, VEHICLE CONTROL AND
DISPLAY.........................INTRO.-7
SYSTEMÐAIR CONDITIONING.......24-14,24-15
SYSTEM (ABS), ANTILOCK BRAKE..........5-1
SYSTEM (ABS) INDICATOR LAMP, ANTI-
LOCK BRAKE.........................8E-2
SYSTEM CAPACITIES, COOLING...........7-38
SYSTEM CHARGE, A/C...................24-5
SYSTEM, CHIME/WARNING BUZZER........8A-1
SYSTEM CLEANING/REVERSE FLUSHING,
COOLING............................7-17
SYSTEMÐCLIMATE CONTROL.......24-22,24-37
SYSTEM COLD CRANKING TEST,
STARTING...........................8A-9
SYSTEM COMPONENTS, COOLING..........7-1
SYSTEM COMPONENTS, STEERING.........19-1
SYSTEM, COOLANT RESERVE/
OVERFLOW..........................7-19
SYSTEM COOLANT ROUTING..............7-1
SYSTEM, COOLING..................0-16,7-1
SYSTEM, CRANKCASE VENTILATION;
EMISSION CONTROL SYSTEMS..........25-5
SYSTEM, CRANKCASE VENTILATION;
LUBRICATION AND MAINTENANCE........0-17
SYSTEM DIAGNOSIS, COOLING.............7-7
SYSTEM DIAGNOSIS, AIR CONDITIONING . . . 24-12
SYSTEM DIAGNOSIS, EXHAUST............11-2
SYSTEM DIAGNOSIS, HEATING...........24-11
SYSTEM DIAGNOSIS, MANUAL
STEERING..........................19-36
SYSTEM DIAGNOSIS, POWER
STEERING...........19-3,19-4,19-5,19-6,19-7
SYSTEM DIAGNOSIS, STARTING..........8A-10
SYSTEM DIAGNOSIS, SUSPENSION AND
STEERING............................2-7
SYSTEM DIAGNOSTIC INSPECTIONS,
STARTER............................8A-9
SYSTEM DISCHARGE, A/C................24-4
SYSTEM, DRAINING COOLING.............7-16
SYSTEM ELECTRICAL TESTS, VEHICLE
SPEED CONTROL.....................8H-5
SYSTEM EVACUATION A/C................24-4
SYSTEM, EVAP (EVAPORATION)
CONTROL...........................25-4
SYSTEM, EXHAUST; INTAKE
MANIFOLD.......................0-20,11-1
SYSTEM FANS, COOLING
.................7-26
SYSTEM, FUEL
........................14-62
SYSTEM, FUEL DELIVERY
................14-2
SYSTEM HOSES, COOLING
...............7-26SYSTEM, HYDRAULIC.................21-160
SYSTEM, ILLUMINATED ENTRY...........8L-20
SYSTEM, INOPERATIVE..................8H-5
SYSTEM, LOCATING A ELECTRICAL........8W-2
SYSTEM NOTATION, METRIC..........INTRO.-8
SYSTEM OPERATION, ABS................5-39
SYSTEM OPERATION, ANTILOCK BRAKE.....5-43
SYSTEM, POWER BRAKE.................0-32
SYSTEM, POWER STEERING..............0-31
SYSTEM POWER-UP AND INITIALIZATION....5-43
SYSTEM PRESSURE RELEASE
PROCEDURE, FUEL...................14-56
SYSTEM PRESSURE TEST, FUEL......14-5,14-48
SYSTEM, REFILLING COOLING............7-17
SYSTEM RELAYS.......................5-42
SYSTEM REPAIR PROCEDURES,
THERMOMETER AND SENSOR...........8C-6
SYSTEM, SPEEDOMETER/ODOMETER;
INSTRUMENT PANEL AND GAUGESÐXJ . . . 8E-2
SYSTEM, SPEEDOMETER/ODOMETER;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-14
SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED ENTRY............8L-21,8L-22
SYSTEM, USING ON-BOARD DIAGNOSTIC . . . 8A-19
SYSTEM, VEHICLE SPEED CONTROL........8A-1
SYSTEM WARNING LIGHTS...............5-42
SYSTEM WIRING AND ELECTRICAL
CIRCUITS, ABS........................5-4
SYSTEMÐYJ VEHICLES, HEATING........24-14
SYSTEMS, AUDIO......................8A-1
SYSTEMS DIAGNOSTICS, BATTERY/
STARTING/CHARGING..................8A-1
SYSTEMS, IGNITION....................8A-1
TABLE, BATTERY CHARGING TIME.........8A-5
TACHOMETER; INSTRUMENT PANEL
AND GAUGESÐXJ....................8E-2
TACHOMETER; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-14
TACHOMETER INOPERATIVE..............8E-3
TACHOMETERÐPCM OUTPUT............14-27
TACHOMETER REPLACEMENT........8E-5,8E-17
TAILGATE ADJUSTMENT...............23-160
TAILGATE HINGE.....................23-159
TAILGATE LATCH AND RELEASE HANDLE . . 23-160
TAILGATE LATCH STRIKER..............23-161
TAILGATE LOCK CYLINDER.............23-160
TAILGATE SERVICE....................23-159
TAILGATE SERVICE INFORMATION........23-159
TAILGATE WEATHERSTRIP SEAL.........23-161
TAILPIPE HEAT SHIELDS, MUFFLER.......13-17
TAILPIPEÐEXHAUST................11-5,11-6
TANK CAPACITIES, FUEL...........14-12,14-62
TANK FILLER TUBE CAP, FUEL....14-12,25-4,25-9
TANK FILLER TUBE, NO-LEAD FUEL.......14-12
TANK, FUEL..........................14-12
TANK PRESSURE RELIEF/ROLLOVER
VALVE, FUEL...................14-15,14-56
TANK, FUEL, SKID PLATE,
BODYCOMPONENTS.............13-16,23-84
TANK SUPPORT STRAP, FUEL............23-86
TANKS, FUEL....................14-12,14-56
TAPPETS, HYDRAULIC...............9-24,9-65
TEMPERATURE CONTROL THERMOSTAT....24-35
TEMPERATURE GAUGE, COOLANT
..........8E-1
TEMPERATURE GAUGE INOPERATIVE,
COOLANT
............................8E-3
TEMPERATURE INDICATOR INOPERATIVE,
COOLANT
............................8E-3
TEMPERATURE INDICATOR LAMP,
COOLANT
............................8E-1
TEMPERATURE SENSOR, COOLANT
........25-9
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL SYSTEM
..............14-55
TEMPERATURE SENSOR, ENGINE
COOLANT; IGNITION SYSTEMS
.....8D-4,8D-22
TEMPERATURE SENSOR, INTAKE AIR
......14-54
TEMPERATURE SENSOR, INTAKE
MANIFOLD AIR
..................8D-5,8D-27
TEMPERATURE SENSORÐPCM INPUT,
ENGINE COOLANT
....................14-21
TEMPERATURE SENSORÐPCM INPUT,
INTAKE AIR
.........................14-20
TEMPERATURE, SENSOR RESISTANCE
(OHMS)ÐCOOLANT TEMPERATURE
SENSOR/MANIFOLD
..................14-43
22 INDEXJ
Description Group-Page Description Group-Page Description Group-Page