Security System - RiESTRICTED ISSUE
AS. 12 INTRUSION SENSOR - RENEW
SRO
86.52.20
. Carefully displace the intrusion sensor from the headlin- ing.
W: View 1 (Fig. 1) shows a vehicle fitted with a sliding
roof. View 2 (Fig. 1) shows a vehicle without a sliding
roof.
. Disconnect the multi-plug and remove the intrusion sen-
Reconnect multi-plug to a new intrusion sensor.
. Locate the intrusion sensor securing studs and carefully
push into the headlining. Make sure the intrusion sensor
is fully seated.
sor.
A5.13
HAND
TRANSMITTER BATTERY - RENEW
SRO 86.52.28
Remove batteries (2 Fig. 2) and discard.
Fit two new batteries making sure the polarity is as shown
Fit and fully seat the transmitter rear cover.
rn Remove the hand transmitter rear cover (1 Fig. 2).
in Fig 2.
AS. 14
SRO 86.52.08
VAL El S WITCI - RENM
J86-I550
Fig. 1
I
I Fig. 2
Open the centre console compartment and carefully dis-
. Disconnect the harness connector and remove the valet
Fitting a new valet switch is the reverse of the removal pro-
place the valet switch.
switch.
cedure. Make sure the switch is fully seated.
Fig.
3
X300 VSM 41 Issue 1 August 1994
Security System - RESTRICTED ISSUE 84
4!sw
A5.15 SECURITY SIREN
(12 CYL) - RENEW
SRO 86.52.03
= Open the trunk and remove the battery cover.
Disconnect the battery ground lead.
Open the hood and remove the headlamp
/ relay cover.
See
SRO 76.1 1.22, Section 13.
Remove the RH air cleaner element. See SRO 19.10.11, Section 5.2.
Remove the RH air cleaner assembly. See SRO 19.10.02, Section 5.2.
. Identify the RH forward harness relays (1 Fig. 1) for subse- quent refitting. Remove the relays and relay bases from
the mounting bracket.
. Disconnect the siren harness multi-plug (2 Fig. 1).
rn Reposition the side harness (3 Fig. 1) to gain access to the
. Undo the siren securing bolts (1 Fig. 2) and remove the
Note:
. Remove the captive washers and the siren securing bolts.
. Fit the siren securing bolts to a new siren.
. Fit and fully seat the captive washers.
. Align the siren securing bolts to the vehicle chassis.
Refitting the remaining components is the reverse of the re
-
moval procedure.
siren securing bolts.
siren
(2 Fig. 2).
The siren securing bolts remain captive.
Tighten the siren securing bolts.
AS. 16 SECURIN SIREN (6 CYL) - RENEW
SRO 8652.03
. Open the trunk and remove the battery cover.
rn Disconnect the battery ground lead.
. Open the hood and remove the headlamp / relay cover.
See SRO 76.1 1.22, Section 13.
. Identify the RH forward harness relays for subsequent re- fitting. Removethe relays and relay bases from the mount- ing bracket.
. Disconnect the siren harness multi-plug.
Reposition the side harness to gain access to the siren se-
. Undo the siren securing bolts and remove the siren.
curing
bolts.
The siren securing bolts remain captive.
Remove the captive washers and the siren securing bolts.
. Fit the siren securing bolts to a new siren.
. Fit and fully seat the captive washers.
= Align the siren securing bolts to the vehicle chassis.
Refitting the remaining components is the reverse of the re
-
moval procedure.
Tighten
the siren securing bolts.
Fig. 1
Fig. 2
X300 VSM Issue 1 August 1994 42
