1994 GMC SIERRA Owners Manual

3. Unplug the
electrical
connector.
4. Turn the bulb to
the left and
i
remove it.
5. Put the new bulb in the lens assembly and turn it to the right until it is
tight.
6. Plug in the electrical connector.
7. Put the headlight lens assembly back into the vehicle. Install and
tighten the two screws.
Front Parkingflurn Signal Lights with
Sealed Beam Headlights
1. Remove the two screws at the inside edge of the parking/turn signal
2. Remove the light assembly by swinging it out from the inside edge and
3. Squeeze the tab on the side of the light socket while turning the socket
4. Pull the socket out of the light assembly.
5. Push in gently on the bulb, turn it to the left and remove it from the
6. Put the new bulb in the socket, gently press in on the bulb and turn it to
7. Put the socket back into the light assembly and turn it to the right until
8. Put the parking/turn signal light assembly back into the vehicle and
light assembly.
sliding
it out at the outside edge.
to the
left.
socket.
the right until it is tight.
it locks.
tighten the screws.
6-55
ProCarManuals.com

Front Parkingnurn Signal Lights with
Composite Headlights
-7
I. Remove the
screws and take
out the parkinghurn
signal light
assembly.
2. Squeeze the tab
on the side of the
light socket while
turning the socket
to the left.
3.
4.
Pull the socket
out
of the light
assembly.
Push
in gently on
the bulb, turn it to
the left and
remove
it from
the socket.
5. Put the new bulb in the socket, gently press in on the bulb and turn it to
the right
until it is tight.
6. Put the socket back into the light assembly and turn it socket to the
right
until it locks.
7. Put the parkinghrn signal light assembly back into the vehicle and
tighten the screws.
6-56
ProCarManuals.com

Side Marker Lights with Sealed Beam and Composite Headhghts
1. Remove the
screws and
pull
out the
parkinghrn
signal light
assembly.
2. Reach through
the opening
and
turn the side
marker bulb
socket to
the left
and remove
it.
3.
4.
Pull the bulb
straight out
of the
socket.
Put
a new bulb
into the socket
and push
it in
until
it is tight.
5. Put the socket back into the side marker assembly and turn it to the
6. Replace the parkinghurn signal light assembly and tighten the screws.
right to tighten
it.
6-57
ProCarManuals.com

Fender Marker Lights-
Dual Rear Wheel Pickup Models
1.
2.
3.
Remove the screws and take
the fender marker
assembly out
of
the fender.
Turn the bulb
socket to the left
and remove it
from the lens assembly.
Pull the bulb straight out of the
socket.
4. Put a new bulb into the socket and push it in until it is tight.
5. Put the socket back into the lens assembly and turn it to th\
e right to
tighten it.
6. Replace the lens and tighten the screws.
ProCarManuals.com

Tailgate Marker Lights
1. Use a screwdriver
to gently pry the
lenshulb assembly from
the lens holder.
2. Unplug the
lenshulb
assembly at the
connector wire.
3. Plug in a new
lensbulb
assembly and
push the
connector wire
into the hole in
the tailgate.
4. Snap the
lenshulb
assembly into the
lens holder.
Roof Marker Lights
1. Remove the
screws and lift off
the lens.
2. Pull the bulb
straight out of the
socket.
3. Put a new bulb
into the socket
and push it in
until it is tight.
4. Replace the lens and tighten the screws.
6-59
ProCarManuals.com

Cargo LighKenter High Mount Stoplamp (CHMSL)
1. Remove the
screws and lift off
the lens.
2. Pull the old bulb straight out
of the
socket.
Rear Lights - Pickup Models
3. Put a new bulb
into
the socket
and push it in
until it is tight.
4. Replace the lens
and tighten the
screws.
1. Open the tailgate.
2. Remove the two
rear light assembly screws
near the tailgate
latch and pull out
the light assembly.
E
6-60
ProCarManuals.com

3. Remove the
screws
from the
bulb retainer and
take
it off the
light assembly.
4. Pull the old bulb
straight
out of the
socket.
5. Put in a new bulb
6. Replace the bulb
retainer.
7. Replace the rear light assembly and tighten the screws.
8. Close the tailgate.
Rear Lights - Chassis Cab Models
..
:F
1. Using your
hands. peel the
rubber seal away
from the lens.
2. Lift the lens off I,. . the light
assembly.
3. Slide the socket
out
of the light
assernbly.
6-61
ProCarManuals.com

4. Push in gently on
the bulb, turn it to
the left and
remove it from
the socket.
5. Put in a new bulb and, pushing in
gently, turn it to
the right until it is
tight.
6. Put the socket back in the light assembly and replace the lens and lens
seal.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from short circuits by a
combination of fuses, circuit breakers, and fusible thermal links in the
wiring itself. This greatly reduces the chance of fires caused by electrical
problems. See “Fuses and Circuit Breakers” in the Index for more
information.
Headlights
The headlight wiring is protected by a circuit breaker in the \
light switch. An
electrical overload will cause the lights to flicker on and of\
f, or in some
cases to remain
off. If this happens, have your headlight wiring checked
right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit breaker and a\
fuse. If
the motor overheats due to heavy snow, etc., the wiper will stop until the
motor cools. Although the circuit is protected from electrical \
overload,
overload due to heavy snow, etc., may cause .wiper linkage damage. Always
clear ice and heavy snow from the the windshield before using \
the
windshield wipers.
If the overload is caused by some electrical problem and
not snow, etc., be sure to get it fixed.
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power windows and other
power accessories. When the current load is too heavy, the circuit breaker
opens and closes. This protects the circuit until the current \
load returns to
normal or the problem is fixed
.
6-62
ProCarManuals.com