1994 CADILLAC DEVILLE Owners Manual

Downloaded from www.Manualslib.com manuals search engine R (Reverse)
Use this gear to back up.
-
NOTICE:
Shifting to ‘6R” (Reverse) while your vehicle is moving forward
could damage
your transaxle. Shift to “R” only after your -
vehicle is stopped. .I
To rock your vehicle back and forth to get out of snow, ice or sand
without damaging your transaxle.
N (Neutral)
In this position, your engine doesn’t connect
restart when you’re already moving, use “N”
“N” when your vehicle is being towed. with
the wheels.
To
(Neutral) only. Also, use
c- Y
A CAUTION:
Shifting out oPCP” (Park) or “N” (Neutral) while your engine is
“racing” (running at high speed) is dangerous. Unless your foot
is firmly on the brake pedal, your vehicle could move very
rapidly. You could lose control and hit people or objects. Don’t
shift out of
“P” (Park) or “N” (Neutral) while your engine is
racing.
I
NOTICE: I
Damage to your transaxle caused by shifting out of “P” (Park)
or “N” (Neutral) with the engine racing isn’t covered by your
warranty.
p_
,

Downloaded from www.Manualslib.com manuals search engine @ Automatic Overdrive
This position
is for normal driving. If you need more power for
passing, and you’re:
- Going less than about 35 mph (56 km/h), push your accelerator
- Going about 35 mph (56 km/h) or more, push the accelerator all
pedal about halfway down.
the way down.
You’ll shift down to the next gear and have more power.
NOTICE:
If your vehicle seems IO start up rather slowly, or if it seems not
to shift gears as you
go faster, something may be wrong with a
transaxle system sensor. If you drive very far that way, your
vehicle can be damaged.
So, if this happens, have your vehicle
serviced right
away. Until then, you can use “2” (Second Gear)
when you are driving less than
35 mph (56 km/h) and @
(Overdrive) for higher speeds.
3 (Third Gear)
This
is like @, but you never go into Overdrive.
Here are some times you might choose
“3” instead of @:
- When driving on hilly, winding roads
- When towing a trailer, so there is less shifting between gears
- When going down a steep hill
93

Downloaded from www.Manualslib.com manuals search engine 2 (Second Gear)
This position gives you more power but lower fuel economy. You can
use
“2” on hills. It can help control your speed as you go down steep
mountain roads, but then
you would also want to use your brakes off
and on.
NOTICE:
Don’t drive in “2” (Second Gear) for more than 5 miles (8 km),
or at speeds over 55 mph (88 km/h), or you can damage your
transaxle. Use
“@” or “3” as much as possible.
Don’t shift into
“2” unless you are going slower than 65 mph
(105 km/h), or you can damage your engine.
1 (First Gear)
This position gives you
even more power (but lower fuel economy)
than
“2.” You can use it on very steep hills, or in deep snow or mud. If
the selector lever is put in “1,” the transaxle won’t shift into first gear
until the vehicle is going slowly enough.
NOTICE:
If your front wheels can’t rotate, don’t try to drive. This might
happen if you were stuck in very deep sand or mud or were up
against
a solid object. You could damage your transaxle.
Also, if you stop when going uphill, don’t hold your vehicle there
with only the accelerator pedal. This could overheat and
damage the transaxle. Use your brakes to hold your vehicle in
position on
a hill.
94

Downloaded from www.Manualslib.com manuals search engine To set the parking brake:
Hold the regular brake pedal down with your right foot. Push down the
parking brake pedal with your left foot. If the ignition is on, the brake
system warning light
will come on.
When you move out
of
“P” (Park) or “N”
(Neutral), if your
engine is running, your
parking brake should
go
off. If it doesn’t, you
have a parking brake
problem and should
have it fixed. In the
meantime,
you can still
release your parking
brake. Just pull on the
manual release lever,
as shown.

Downloaded from www.Manualslib.com manuals search engine NOTICE: II I
Driving with the parking brake on can cause your rear brakes \
to Lyav 1’
I
overheat. You may have to replace them, and you could also
damage other parts
of your vehicle.
I IU
If vou are towing a trailer and are parking on any hill: See “Towing a
Trailer” in the Index. That section shows what to do first to keep the
trailer from moving.
SHIFTING INTO “P” (PARK)
96

Downloaded from www.Manualslib.com manuals search engine - Steering Column Shift Lever
1. Hold the brake pedal down with your right foot.
2. Move the shift lever into “P” (Park) position like this:
3.
4.
5.
0 Pull the lever
toward you.
0 Move the lever
up as far as it
will
go.
With your right foot still holding the brake pedal down, set the
parking brake.
Move the ignition key to “Lock.”
Remove the key and take it with you.
If you can walk away from your
vehicle with the ignition key in your hand, your vehicle is in “P” (Park).
97

Downloaded from www.Manualslib.com manuals search engine Leaving Your ‘vehicle With the Engine Running
L
’ CAUTION:
It can be dangerous to leave your vehicle .with the engine I-
running. Your vehicle could move suddenly if.the shift lever is
noi Eully in “P” (Park) with the parking brake firmly set. And, if
I- you leave the vehicle with the engine running, it could overhe\
at
and even catch fire.
You or others could be injured. Don’t leave
your vehicle with the engine running unless you have to.
If you have to leave your vehicle with the engine running, be sure your
vehicle is in “P” (Park) and your parking brake is firmly set before you
leave it. After you’ve moved the shift lever into the “P” (Park) position,
hold the regular brake pedal down. Then, see
if you can move the shift
lever away from “P” (Park) without first pulling it toward you. If you can,
it means that the shift lever wasn’t fully locked into “P” (Park).
SHIFTING OUT OF “P9’ (PARK)
Your Cadillac has a brake-transaxle shift interlock. You have to fully
apply your regular brake before you can shift from “P” (Park) when the
ignition is in the “Run” position. See “Automatic Transaxle”
in the Index.
If you cannot shift out
of “P” (Park), ease pressure on the shift lever --
push the shift lever all the way into “P” (Park) you maintain brake
application. Then move the shift lever into the gear you want.
If you ever
hold the brake pedal down but still can’t shift out of “P” (Park), try this:
1. Turn the key to “Off.” Open and close the driver’s door to turn off the
Retained Accessory Power feature.
2. Apply and hold the brake until the end of Step 4.
3. Shift to “N” (Neutral).
4. Start the vehicle and then shift to the drive gear you want.
5. Have the vehicle fixed as soon as you can.
r
r
L
98

Downloaded from www.Manualslib.com manuals search engine Torque Lock
If you are parking on a hill and you don’t shift your transaxle into “P”
(Park) properly, the weight
of the vehicle may put too much force on the
parking pawl in the transaxle. You may find it difficult to pull the shift
lever out
of “P” (Park). This is called “torque lock.” To prevent torque
lock, set the parking brake and then shift into “P” (Park) properly before
in the Index.
__*
-. you leave the driver’s seat. To find out how, see “Shifting Into ‘P’ (Park)”
If “torque lock” does occur, you may need to have another vehicle push
yours a little uphill to take some
of the pressure from the transaxle, so
you can pull the shift lever out of “P” (Park).
_-
P-NG OWR THINGS TiHATBURN
99