1992 MAZDA 323 Workshop Manual Suplement

S INDEX
INDEX
1. Bonnet bulge
Removal ! Installation _. __. . . , , . . l.. . .__ page. S-
2. Fro.nt bumper
7 Removal / Installation
. . . . . 1 . . . . . . . ,‘... page S-
Disassembly / Assembly 8
. ..a I........
page S- 9
s-2 3. Rear skirt
Removal / t’nstaltation 4. Wheel arch molding .....n.....ba..... page S-l 0
Removal / Installation
. .-. . . , , ..‘. .-. page S-l 1
OUTLINE
l The exteric
bofiy.
OUTLtNE 01
i BONNET BUt
l Bonnet bulg
a high-qualit

l The exterior parts are designed to emphasize the function and appearance of the superbly proportioned
body.
: OUTtlNE OF CONSTRUCTION
1 xosx.303
.c
Bonnet bulges are provided in bonnet
. . . . . . . . . . . . ..I................~.....
s-3
A large, body-colored front bumper fascia is adopted., , ..,..,.... S-4
Wheel arch moldings are fitted to fenders . . . . . . . ,..*. l.. . . . . . . . . . . . . . . . . . S-5
- Air inlet area of radiator grille is enlarged
................................. S-4
- Bumper mesh is provided in front bumper
..............................
s-4 Rear skirt is attached under rear bumper.. ............................... S-5
13EOSX-304 BONNET BULGE
l Bonnet bulges are fittGd to the bonnet to match the dynamic appearance of the vehicle and to give it
a high-quality look.

UUTLINE
RADfATOR GRfLtE
l The air inlet area of the radiator grille is enlarged for improved cooling efficiency.
FRONT BUMPER
l The large front bu,mper includes fog lights and bumper mesh to give the vehicle a dynamic appearance.
l tight and rigid polyurethane is used for the bumper fascia.
l The air inlet area is adopted for improved cooling efficiency.
s-4
REAR SKI
l The rear 5
l Light and
WHEEL AR4
l Wheel arc

OUTLINE S
REAR SKIRT
13EOSX-308 l The rear skirt is added for improved vehicle aerodynamics.
l Light and rigid polyurethane is used.
WHEEL ARCH MOLDING
13EOSX-30E a Wheel arch moldings are fitted to the front and rear fenders to give the vehicle an aggressive look.

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if

BONNET BULGE S
BONNET BULGE
COMPONENTS
Rem&at ! Installation
1. Removal in the order shown in the
figure.
2. Install in the reverse order of removal.
I . Bonnet butge’

S
FRONT BUMPER FRONT BUMPER
COMPONENTS
Rem’ovat ! Installation
1. Removal in the order shown
2. Install in the reverse order of
1 in the figure.
removal.
-9-9.8 Nm 170-100 kgfem,
U-87 h.lbfJ
f4-m Ikgf-m, ft-lbf J
13EOSX-312
4. Front bumper
Disassembly / Assembly
. . . . . . . . . ..m... page S-9 1. Radiator grille
2. Front conbination light
3. Headlight
5-8
Disassembh
I . Disassemi
2. Assemble
t
1. Fog lights
-
a
-I. 2. Bumper rear
3. Bumper me

FRONT BUMPER S
Disassembly / Assembly
I. Disassemble in the order shown in the figure.
2. Assemble in the reverse order of disassembly.
i
1, Fog lights
2. Bumper reinforcement
3. Bumper mesh 4. Hook cover
5. Bumper fascia