1991 MITSUBISHI ECLIPSE clutch

21-242AUTOMATIC TRANSAXLE - Transaxle Assembly Manual control
17700563. After installing new O-ring on manual control shaft, draw
shaft back into case, then install set screw and gasket. Alsoinstall detent steel ball, seat and spring at the same time.
4. Install sprag rod support and tighten two bolts.
Sprag rod support bolts:
20-27 Nm (15-19 ftlbs.)5. Using the special tool, tap in the bearing outer race.
6. Press-fit the bearing inner race to the transfer
djrven gear
and press-fit the bearing outer race to the transaxle end
clutch side.

AUTOMATIC TRANSAXLE - Transaxle Assembly 21-25143. Install kickdown band; attach the ends of band to the ends
of anchor rod and servo piston rod.
44. Putting the kickdown drum into the kickdown band, align
the spline of the drum to that of the reverse sun gear. Placekickdown band on kickdown drum and tighten kickdown
servo adjusting screw to keep band in position.
45. Apply a coating of petrolatum to thrust bearing
#8, and
then attach to the kickdown drum.
46. Apply a coating of petrolatum to thrust race
#7, and then
attach to the rear clutch hub.
47. Install clutch hub to sun gear splines.

AUTOMATIC TRANSAXLE - Transaxle Assembly Thrust bearing
#41750200Fro& clutch
,75020,48. Attach thrust bearing
#6 onto the hub with petrolatum.
rc;I
v49. Apply a coating of petrolatum to thrust washer
#2 and
thrust bearing #4, and then attach to the rear clutch
assembly.50. Combine the rear clutch assembly and the front clutch
assembly.51. Install the clutch assembly.
52. Install the differential assembly.

AUTOMATIC TRANSAXLE - Transaxle Assembly 21-253Thrust race
53. If end play which was measured and recorded at disassem-
bly is not standard value, adjust end play to specification byselecting thrust race
#3.Standard value
:0.3-1.0 mm (.012-.040 in.)
54. Attach the reused thrust washer
#I, or the one selected in
step 51 to the front clutch by using petrolatum.
55. Install special tool to the case.
56. Attach the reused thrust race
#3 or the one selected in
step 53 to the oil pump by using petrolatum.
57. Install new oil pump gasket and the oil pump assembly.

AUTOMATIC TRANSAXLE - Transaxle Assemblv 21-255
Spacer
1700108
TFA002066. Place the spacer selected in Step 65 on the outer race of
the differential bearing.
67. Apply silicone grease to hatched area (all gasket surface) oftransaxle case.
68. Install new case gasket on transaxle case.
69. Install converter housing and tighten 14 bolts to
19-23 Nm
(14-16 ft.Ibs.).70. Install end clutch shaft. Be sure to install the longest spline
toward the front as shown.
71. Fit the thrust washer to the return spring at the end clutch
side.

21-256AUTOMATIC TRANSAXLE - Transaxle Assembly
IThrust \\I72. Install the end clutch hub to end clutch.73. Attach, by petrolatum, thrust bearing # 13 to the end clutch
hub.74. Install end clutch assembly.
75. Install a new O-ring in the grooves of the end clutch cover.
Caution1. Install so that the O-ring is not twisted.
2. Apply
a sufficient amount of automatic transmission
fluid to the bearing.
76. Attach the end cover and fasten it with four bolts.
Caution
When installing the end cover, be sure the screw hole iscorrectly aligned. If the end cover is turned (after it is
installed) in order to align with the screw hole, the
iiO-ring may be twisted as a result.
d

21-266 AUTOMATIC TRANSAXLE -Transaxle Assembly TRANSAXLE ASSEMBLY
DISASSEMBLY AND REASSEMBLY

20.Pressure pla?e21.Brake disc22.Brake plate23.Reaction plate
24. Reverse sun gear25. Thrust bearing
#826. Thrust race
#9---
1.Torque converter2.Oil pump assembly3.Gasket4.Thrust washer #I5. Front clutch assembly
6. Thrust race #37. Thrust bearing #48. Thrust washer #227. l-or-ward sun gear
9. Rear clutch assembly28. Planetary carrier assembly
10. Thrust bearing #529.Thrust bearing#I0
11. Rear clutch hub30.Output flange
12. Thrust race
#631. Oil level gauge
13. Thrust bearing #732. Oil filler tube14.Kickdownband33.
Snap ring15.Kickdowndrum34. Kickdown servo switch16.Snap ring35.Snap ring
Ii524
23
TFA0405’36.
Kickdown servo piston
37.Spring
38.Anchor rod
39.Detent assembly40. Manual control shaft
41. Parking roller support
42.Oilpan43.Gasket44. Oil temperature sensor
45.Oil screen
46. Valve body assembly
47. Manual control lever
48.Inhibitor switch49. End clutch shaft50.Bearing retainer51.Thrust bearing #I152. End clutch hub53.Thrust washer
54. End clutch assembly
55.O-ring
56. End clutch cover
57.Pulse generator58:Lock bolt59.Idler shaft60.Idlergear61.Spacer
62.Gasket

21-268 AUTOMATIC TRANSAXLE -Transaxle Assembly DISASSEMBLY AND REASSEMBLY

TFA0409
1.Torque converter2.Oil pump assembly3.Gasket4.Thrust washer #I5.Front clutch assembly
6. Thrust race #37.Thrust bearing #48. Thrust washer
#29.Rear clutch assembly
10. Thrust bearing #511.Rear clutch hub12.Thrust race #613.Thrust bearing #714.Kickdown band15.Kickdown drum16.Snap ring
17.Center support18.Wave spring19.Return spring20.Pressure plate21.Brake disc22.Brake plate23.Reaction plate24.Reverse sun gear25. Thrust bearing #826.Thrust race #927. Forward sun gear
28.Planetary carrier assembly29. Thrust bearing #IO30.Output flange31.Oil level gauge32.Oil filler tube33.Snap ring34.Kickdown servo switch35.
Snap ring36.
Kickdown servo piston
37.Spring38.Anchor rod39.Detent assembly40. Manual control shaft
41. Parking roller support
42.Oilpan43.Gasket44.Oil temperature sensor45.Oil screen46.Valve body assembly47.Manual control lever48.Inhibitor switch49.End clutch shaft50.Bearing retainer51.Thrust bearing #I 1
52. End clutch hub
53.Thrust washer54. End clutch assembly55.O-ring
56. End clutch cover
57.Pulse generator58.Lock bolt59.Idler shaft60.Idler gear61.Spacer
62.Gasket