1991 MITSUBISHI 3000GT engine

32-1
POWER PLANTMOUNT
CONTENTSMZAA- _
ENGINE MOUNTING........................................
3SPECIFICATIONS................................................2
ENGINE ROLL STOPPER
5Service Specifications....................................2....................................
TRANSAXLE MOUNTING................................4RIGHT MEMBER, LEFT MEMBER AND
CROSSMEMBER”................................................6TROUBLESHOOTING........................................2
SPECIAL TOOLSAbnormal Noise....................................................
2
Excessive Engine Wobble or Vibration
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

POWER PLANT MOUNT - Engine Mounting
ENGINE MOUNTING
REMOVAL AND INSTALLATION
32-3
l Raise and Suspend the Engine to the12 Nm
lOO-120Nm(9 ftlbs.
72-87ftlbs. > &6
rI’ I/4
c*1. Connection for air hose G
2. Cruise control pump and link assembly

3. Engine mount bracket and body
connection bolt
4. Engine mount bracket
l *5. Mounting stopper
6. Dynamic damperOlFOO50
3emoval steps
SERVICE POINT OF REMOVALM32GBAK2. REMOVAL OF CRUISE CONTROL PUMP AND LINK
ASSEMBLY
Remove the actuator mounting nuts and place the actuatorwhere it will not interfere with the work.
INSPECTIONM32GCAMl
l Check each insulator for cracks or damage.
l Check each bracket for deformation or damage.
1SERVICE POINT OF INSTALLATIONM32GDAW
5. INSTALLATION OF MOUNTING STOPPER
Attach the engine mounting bracket so that the arrow mark
on the mounting stopper is in the direction as shown in the
illustration.TSB Revision

POWER PLANT MOUNT - Engine Roll Stopper
ENGINE ROLL STOPPER
REMOVAL ANDINSTALLATION
32-5
MJZGF- .
Pre-removal and Post-installationOperationl Removal and Installation of Condenser
Fan Motor Assembly
(Refer to GROUP 55 - Condenser and
Condenser Fan Motor.)
l Removal and installation of Catalytic
Converter (Left)
(Refer to GROUP 15 -Turbocharger.)
45 Nm/33 ft.lbs.
43
- 51 ftlbs.Front stopper bracket removal steps
1. Front roll stopper bracket and engine
connection bolt
2. Front roll stopper bracket installation bolt
3. Front roll stopper bracket
4. Heat protector

50-60 Nm36 - 43 ft.lbs.Rear roll stopper bracket removal steps
5. Air hose A
6. Air intake hose C
l +7. Rear roll stopper bracket and engine
connection bolt
8. Rear roll stopper bracket installation bolt
+* *+9. Rear roll stopper bracketIO. Heat protector OlFOO30
II\ OlFOO4:
SERVICE POINT OF REMOVALM32GEAL
9. REMOVAL OF REAR ROLL STOPPER BRACKET
(1) Slightly raise the rear roll stopper bracket.
(2) Turn the rear roll stopper bracket in the direction shownin the illustration and lift upward to remove.
INSPECTIONM32GCAM3l Check each insulator for cracks or damage.
l Check each bracket for deformation or damage.
9TSB Revision
SERVICE POINTS OF INSTALLATIONM32GJAC
9. INSTALLATION OF REAR ROLL STOPPER BRACKETInstall the rear roll stopper bracket as shown in the
illustration.7. INSTALLATION OF REAR ROLL STOPPER BRACKET
AND ENGINE CONNECTION BOLT
Install the bolt as shown in the illustration.

33B-4ELECTRONIC CONTROL SUSPENSION (ECS) - TroubleshootingTROUBLESHOOTING
M33EAAE
QUICK REFERENCE CHART FOR TROUBLESHOOTING
SymptomsXS
indicator lightdoes not switch
TROUBLESHOOTING HINTS
“1. The G. sensor is a sensor associated with ride control (detecting pitching, bouncing and rough road). If itfails, therefore, ride control stops.
“2. A self diagnostic decision on the steering angular velocity sensor is made by the ECS control unit which
internally detects the voltages of the two sensor output lines connected to the ECS control unit to detectan open circuit in the signal line. When the signal line is short-circuited or when the power line is
open-circuited, however, it cannot be detected. In a situation where anti-roll control only stops, if
self-diagnosis code No. 21 is not on display, a short-circuited sensor output line or open-circuited sensorpower line is suspected.
“3. The vehicle speed sensor is a sensor associated with attitude controls (anti-dive, anti-squat) and steering
stability controls (anti-roll, high speed sensitive controls). If all these controls stop, therefore, trouble in the
sensor is suspected. The vehicle speed sensor is also in use for operation of the speedometer and for theother electronics controlled systems for the engine, automatic transaxle, etc.
“4. The sensor associated with anti-squat control is the throttle position sensor. The sensor is also used for
control of the engine and automatic transaxle. If the sensor fails, therefore, the check engine light in the
combination meter will light, and engine self-diagnosis code No. 14 will be output. In a situation whereanti-squat control only stops, therefore, if the check engine light does not light, defective wiring is
suspected between the ECS control unit and throttle position sensor.
TSB Revision

ELECTRONIC CONTROL SUSPENSION (ECS) - Troubleshooting 33B-11
I I7
Anti-squat control only stops.III
L,
I
Using MUT, check service data onthrottle position sensor. Good?
Yes
rCheck by entering simulated vehicle speed from MUT to
simulate anti-squat control. (Refer to P.33B-16.) Good?!
1 Good1 ) Replace ECS control unit. 1
I
1I II
NoDoes check engine light illuminate?>Is continuity provided between No. 2 terminal of throttleposition sensor and No. 59 terminal of ECS controlunityII
Yes
i
Correct harness.
1Check throttle position sensor. (Refer to P.33B-20.) Good?III1
connector and check harness con-nector with ignition switch at ON.
No. 1 terminal voltage and continuityNo
Is
between No. 4 terminal and groundcontinuity provided across the following areas?
up to specification? (Sensor powerthrottle position sensor and engine control unit
No. 1 and 61 terminals
supply and ground)
No. 4 and 72 terminalsStandards:
INo. 1 terminal5 V
YesNo. 4 terminal
Continuity provided
Yes-1 1 Correct harnei:
”
Replace throttle position sensor.TSB Revision

ELECTRONIC CONTROL SUSPENSION (ECS) - Circuit Diaaram 33B-23
IGN:sw1::A?-m
I&
177
i '
3
I
2YJ
-+d
T-J
---
ON(IG2)SV
el
ENGINEf"BTROL
GNDIfi
1234
J333256‘78
6461 72>
I
I
CLL2c
I
,Jm4,\/\THROTTLE;;;EI;;ON
4-1
jV
f
. I
!i
ss’
2
___--_--- _-- ------2354 55F
"pLl
cl w&
114 3__------ -------
I
nimCL
IGNITIONSWITCH(IG1)18Bl
NON-TURBO\
G-R
COMBI-
%kiN'(REED>
G SENSOR
lf?EzJi
STEERING
WHEEL ANGLE
SPEED SENSOR
liZI1 2 3aTSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-7
ANTI-LOCK BRAKING SYSTEM TROUBLESHOOTlilGPARTICULAR PHENOMENA OF THE
LANTI-LOCK BRAKING SYSTEMModels equipped with the anti-lock braking system
(ABS) may exhibit one or more of the following
phenomena from time to time, but none of these
are abnormal.
(1) A pulsing feeling in the brake pedal, or vibration
of the body or the steering wheel, when the
anti-lock braking system is activated by sudden
braking or by braking on a slippery road surface.
.9ctually, this phenomenon is an indication that
the anti-lock braking system is functioning nor-
mally.(2) When the vehicle speed reaches approximately
6 km/h (4 mph) after the engine is started and
the vehicle starts off (for the first time), a
whining motor noise may be heard from the
engine compartment if the vehicle is traveling in
a quiet place, but this noise is simply the result
of a self-check being made of the anti-lock
braking system operation.
TROUBLESHOOTING METHODSProblems related to the anti-lock braking system
(ABS) can be classified into two general categories:
problems in the electrical system and those in the
Lhydraulic system.For problems in the electrical system, the
self-diagnosis function is built into the electronic control
unit (E.C.U.) causing the ABS warning light to
illuminate as a warning to the driver. In this instance,
checks can be made by using the multi-use tester
and oscilloscope.
Problems in the hydraulic system (poor braking,
etc.) can be located in the same way as for ordinary
brakes. There is, however, the necessity to check to
determine whether the problem is related to ordin-
ary brake components or to the components related
to the ABS. To make this check, use the multi-use
tester.
HOW TO USE THE TROUBLESHOOTING
FLOW CHART(1) Using the flow chart, check the ABS warning
light light-up sequence. Read the diagnosis
codes and check the condition of braking opera-
tion.
(2) Following the check chart listed in the remedy
column, perform the checks. There are [Explana-
tion] and [Hint] in each check chart. Refer to
them when troubleshooting.
NOTEECU: Electronic control unit
HU: Hydraulic unit
MUT: Multi-use tester
1 TSB Revision

35-8SERVICE BRAKES -Anti-lock Braking System Troubleshooting
TROUBLESHOOTING (ABS - FWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
(2) With the ignition key in the “START” position,
below up to the time the engine starts?power to the ABS ECU is interrupted and the
(1) When the ignition key is turned to the “ON”ABS warning light remains lit because the valve
position, the ABS ECU causes the ABS warningrelay is OFF.
light to flash twice in about one second (during
(3) When the ignition key is returned from the
which the valve relay self check is made) and“START” position to the “ON” position, the
then causes it to go out.ABS warning light flashes twice in about one
second (during which. the valve relay self check
-is made again) and then goes out.
ABS warning
ONlightII
-I
keyACC,
LO!: +--14A0589
Yes>CONTINUED ON NEXT PAGE
No
”
weenABS warning
1 TSB Revision