1991 MITSUBISHI 3000GT sensor

EMISSION CONTROL - Evaporative Emission Control System17-7
PURGE CONTROL SYSTEM INSPECTION M17lBBP
Barometric pressure sensor
Engine control unit
7EM0161I-----I
\7EM0140t
(1) Disconnect the vacuum hose (red stripes) from the throttle
body,and connect it to a hand vacuum pump.
(2) Plug the nipple from which the vacuum hose is discon-
nected.
(3) Under the engine conditions shown below, check by
applying vacuum from a hand vacuum pump.
When engine is cold
-engine coolant temperature:
60°C (140°F) or less
When engine is hot
-engine coolant temperature:
70°C (158°F) or higher
Engine operatingcondttionApplying vacuumResult
ldllng375 mmHg(14.8 In.Hg)Vacuum is maintalned
I
after staitingengineNOTEThe vacuum will leak con-tenuously if the altitudeis 2,200 m (7.200 ft.) or
higher, or the intake airtemperature is 50°C(I 22°F) or higher.TSB Revision

17-8EMISSION CONTROL - Evaporative Emission Control System
PURGE CONTROL SYSTEM INSPECTION M17IBBQ
Canister
Purge control
valve\
PI IrnQ rnntrnlI.1 I
kXffo~~~~r~~ ’ I I-J
relay
Barometric pressure sensor
Intake air temperature sensor
Engine coolant temperature sensor
II1 I IAir flow sensor
Engine control unit
6EM0215(1) Disconnect the purge air hose from the air intake hose, and
plug the air intake hose. Then, connect the hand vacuum
pump to the purge air hose.
(2) Under the engine conditions shown below, check by
applying vacuum from a hand vacuum pump.
When engine is cold
-engine coolant temperature:
60°C (140°F) or less
Engine operating
conditionApplying vacuumResult
Idling
375 mmHgVacuum is maintained
3,000 rpm(14.8 in.Hg)When engine is hot
-engine coolant temperature:
70°C (158°F) or higher
Engine operating
condition
Idling
3,000 rpm within
three minutes after
starting engine
3,000 rpm after
three minutes
have elapsedafter startingengine
Applying vacuum
375
mmHg(14.8 in.Hg)
Try applyingvacuum
375
mmHg(14.8 in.Hg)
Result
Vacuum is marntained
Vacuum leaks
Vacuum WIII be main-tained momentarily, after
which it will leak.
NOTEThe vacuum WIII leak con-
tinuously if the altitude
is 2,200 m
(7,200 ft.) orhrgher. or the Intake arrtemperature is 50°C(122°F) or higher.
1 TSB Revision

17-10EMISSION CONTROL - Evaporative Emission Control System
I-6EM13i(4) Apply a vacuum and check for airtightness when voltage
applied directly to the purge control solenoid valve and
when the voltage is discontinued.
Battery voltageResultNon-Turbo When applied
Vacuum leaks
When discontinuedVacuum is maintained
TurboWhen applied
When discontinued
Vacuum is maintained
Vacuum leaks
(5) Measure the resistance between the terminals of the
solenoid valve.
Standard value: 36
- 44 R [at 20°C (68”F)]
AIR FLOW SENSOR, ENGINE COOLANT TEMPER-ATURE SENSOR AND INTAKE AIR TEMPERA-
TURE SENSORM17lBGFTo inspect these parts, refer to GROUP 13
- MPI System
Components.
AIR CONDITIONER SWITCHMl7IBHF
To inspect the air conditioner switch, refer to GROUP 55
- Air
Conditioner Switch.
OVERFILL LIMITER (TWO-WAY VALVE)M17IBEFTo inspect the overfill limiter (two-way valve), refer to GROUP
13
- Fuel Tank.
CANISTERM17lBIFTo inspect the canister, refer to GROUP 13
- Fuel Line and
Vapor Line.
FUEL FILLER CAP INSPECTIONM17IBJBCheck the gasket of the fuel filler cap, and the filler cap itself,
for damage or deformation; replace the cap if necessary.
TSB Revision

EMISSION CONTROL -Exhaust Gas Recirculation (EGR) System17-11
EXHAUST GAS RECIRCULATION (EGR) SYSTEMrm?MA- -COMPONENTS LOCATION
L
,
i
-
\\
(%vTT
I
4/ -I---Id/- -3Th
--02
I
1-a\\
IJ-l f--An7FUlOl
NameSymbol
~ EGR control solenoidvalve1 :
EGR temperature sensor ~
EGR valve
7EM014f
1TSB Revision

EMISSION CONTROL - Exhaust Gas Recirculation IEGR) Svstem17-13
GM159
QQQQQQ7FMnn4EGR VALVE - Non Turbo, Turbo>
M17lCKJ
INSPECTION(1) Remove the EGR valve and check it for sticking, deposit of
carbon, etc.
If such condition exists, clean with adequate solvent to
ensure tight valve seat contact.
(2) Connect a hand vacuum pump to the EGR valve.
(3) Apply a vacuum of 500 mmHg (19.8 in.Hg.) and check
airtightness.
(4) Blow in air from one passage of the EGR to check condition
as follows.
INSTALLATIONInstall a new gasket and EGR valve, tighten bolts to specified
torque.
Specified tightening torque: 19
.Nm (13 ft.lbs.)
EGR TEMPERATURE SENSOR M17lCYC
INSPECTION(1) Remove the EGR temperature sensor.
(2) Place the EGR temperature sensor in water, and then
measure the resistance value between terminals 1 and 2
while increasing the water’s temperature.
Replace the EGR temperature sensor if there is a significant
deviation from the standard value.
INSTALLATIONInstall the EGR temperature sensor tighten to specified torque.
Specified tightening torque: 11 Nm (8
ftlbs.)
EGR CONTROL SOLENOID VALVE Non Turbo, Turbo>MlllCRE
INSPECTION
NOTEWhen disconnecting the vacuum hose, make an identification
mark on it so that it can be reconnected to the original position.
(1) Disconnect the vacuum hose (yellow and green stripe) from
the solenoid valve.
(2) Disconnect the harness connector.
(3) Connect a hand vacuum pump to the nipple to which the
green-striped vacuum hose was connected.
1 TSB RevisionI

22-1
iv,MANUAL ~
TRANSAXLE
~
I
CONTENTSM22AA. -
MANUAL TRANSAXLE . . . . . . . . . . . .._...48INPUT SHAFT ASSEMBLY_..________.............: . . . . . . . . . . . . . . . . . . . . . . . . . .30
GENERAL INFORMATION....................................................48
SERVICE ADJUSTMENT PROCEDURES
............................51
Drive Shaft OilSealsReplacement....................................
52Speedometer Cable Replacement....................................
53Transfer Oil Seal Replacement............................................53Transmission Oil Level Inspection....................................51Transmission Oil Replacement............................................51
SHIFT LEVER ASSEMBLY....................................................
53
SPECIAL TOOLS........................................................................50
SPECIFICATIONS
....................................................................49
General Specifications........................................................49Lubricants............................................................................49
TRANSAXLE ASSEMBLY....................................................56,60
TRANSAXLE CONTROL*........................................................54
TRANSFER ASSEMBLY
........................................................59
MANUAL TRANSAXLE ....................2
CLUTCH HOUSING ASSEMBLY............................................46
DIFFERENTIAL ASSEMBLY
....................................................43
5TH SPEED SYNCHRONIZER ASSEMBLY
........................28
GENERAL INFORMATION
....................................................2INTERMEDIATE GEAR ASSEMBLY
....................................
OUTPUT SHAFT ASSEMBLY................................................
SERVICE ADJUSTMENT PROCEDURES............................
Drive Shaft Oil Seals Replacement....................................Speedometer CableReplacement....................................Transmission Oil Level Inspection....................................Transmisston Oil Replacement............................................
SHIFT LEVER ASSEMBLY....................................................
SHIFT RAILS AND FORKS....................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................
Lubricants............................................................................
Sealants and Adhesives........................................................Service Specifications........................................................
Snap Ring (for Adjustment) and Spacer............................
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................
TRANSAXLE ASSEMBLY _____...._........__....................................
TRANSAXLE CONTROL*. . ..________.___.._ ..__._.__.__...............
36
41
9
10
9
9
9
13
42
6
3z
63
3
45
14
11TROUBLESHOOTING
___.._______._____.......,..................................8
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the
SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

23-1
AUTOMATIC
TRANSAXLE
CONTENTSMZJAA- _
ANNULUS GEAR AND TRANSFER DRIVE GEARTransmission Fluid Level Inspection................................46SET................................................................................................
102Transmission Fluid Replacement........................................
46
DIFFERENTIAL........................................................................104SPECIAL TOOLS........................................................................
16
:......................................... 12IEND CLUTCH ASSEMBLY....................................................99SPECIFICATIONS..........................
FRONT CLUTCH ASSEMBLY................................................95
GENERAL INFORMATlON....................................................2
KICKDOWN SERVO................................................................
107
LOW-REVERSE BRAKE............................................................
107
OIL PUMP....................................................................................93
PLANETARY GEAR................................................................
100
REAR CLUTCH ASSEMBLY....................................................97
SELECTOR LEVER ASSEMBLY............................................58
SERVICE ADJUSTMENT PROCEDURES............................46
Accelerator Switch
Inspection and Adjustment................
50Drive Shaft Oil Seals Replacement....................................
52Inhibitor Switch and Control Cable Adjustment................
52Key Interlock Mechanism Check........................................50KickdownServo Adjustment................................................
47Line Pressure Adjustment....................................................
48Reducing Pressure Adjustment........................................
49Selector Lever Operation Check........................................
50Shift Lock Mechanism Check............................................51Speedometer Cable Replacement....................................53
General Specifications........................................................12Lubricants............................................................................15Service Specifications........................................................12Spacer and Snap Ring........................................................13Valve Body Spring Identification Chart............................13
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................106
TRANSAXLE ASSEMBLY........................................................62
TRANSAXLE CONTROL*........................................................54
TRANSAXLE OIL COOLER, HOSES, TUBES
....................66
TRANSFER SHAFT....................................................................92
TROUBLESHOOTING............................................................
19
A/T Safety-lock System Troubleshooting........................44Converter Stall Test............................................................
43
Diagnosis and Test
................................................................
22
Element in Use at Each Position of Selector Lever........31Inspection
of ControlSystem............................................
28Inspection of Electronic Control System Components....32Oil Pressure Tests................................................................
39ShiftPatterns....................................................................
31,42Troubleshooting Guide........................................................
20
VALVE BODY. . . .._._.................................................................... 108
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3668GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
(3) MlTSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
ISRS or any SRS-related component.

AUTOMATIC TRANSAXLE - Troubleshootincl23-19Based upon use of the troubleshooting
Checks should be made of fluid levels and
the condition of the ATF, as well as the
condition of the manual control cables;
adjustments should then be made if found
to be necessary.
If a presumption has been made that there
is an abnormal condition somewhere in
the electronic-control system, check the
fault code, in order to determine the
probable location of the problem, by using
a multi-use tester or voltmeter.
I
When the abnormal system is discovered,
check each element (sensors, etc.) one by
one, and make repairs as necessary.
IWhen the abnormal condition is presumed
to be in the oil-pressure-control system
When the result of the oil-pressure test
does not satisfy the specified pressure,
check each system at places related to the
valve body, check the oil-pressure pas-
sages for leakage, etc.
I
If the problem isunusually dirty ATF,
abnormal noises, oil leakage, or slippage of
the clutch or brakes, or an abnormal
condition of the transaxle itself, disassem-
ble and repair the transaxle.
TROUBLESHOOTINGM23EEAYFunctional malfunctions of the ELC4A/T can lead to other
problems, such as those described below:(I
) Improper maintenance and/or adjustments
(2) Malfunctions of the electronic control functions
(3) Malfunctions of mechanical functions
(4) Malfunctions of hydraulic control functions
(5) Malfunctions of engine performance
etc.
In order to properly determine (“Troubleshoot”) the source of
these malfunctions, it is first essential to methodically question
the user concerning the details of the problem, such as the
condition of the problem, the situation at the time the problem
occurred, and any other relevant information, all in as much
detail as possible. The user should also be asked whether or
not the problem has occurred more than once, and under what
conditions.
Subsequently, certain tests should be conducted in a certain
order, as described at the left.
TSB Revision