1991 MITSUBISHI 3000GT sensor

i
LJ
AUTOMATIC TRANSAXLE - Transaxle Assembly
DISASSEMBLY AND REASSEMBLY23-65
M23LEAN
11
Z:4.
::
;:9.10.11.
12.
13.
14.
15.
16.8
%&,kd!~~ / I!- 1A8 ii9
-114Torque converter~.I~I~~~ assembly
Thrust washer
#IFront clutch assembly
Thrust race #3
Thrust bearing #4Thrust washer #2Rear clutch assemblyThrust bearing #5Rear clutch hubThrust race #6Thrust bearing #7Kickdown bandKickdown drumSnap ring
17.Center support18.Wave spring19.Return spring
20.Pressure plate21.Brake disc
22.Brake plate
23.Reaction plate
24. Reverse sun gear
25. Thrust bearing #8
26. Thrust race #927. Forward sun gear
28. Planetary carrier asseml
29.Thrust bearing #I030.Output flange
31. Oil level gauge
32. Oil filler tube33.Snap ring34. Kickdown servo switch35.Snap ring26
25
24
TFA040936.
Kickdown servo piston37.Spring
38.Anchor rod39.Detent assembly
40. Manual control shaft
41. Parking roller support
42.Oilpan43.Gasket44. Oil temperature sensor45.Oil screen46. Valve body assembly
47. Manual control lever
48.Inhibitor switch
49. End clutch shaft
50.Bearing retainer51.Thrust bearing #I1
52. End clutch hub53.Thrust washer
54. End clutch assembly
55.O-ring56. End clutch cover57.Pulse generator
58:Lock bolt
59.Idler shaft
60.Idlergear
61.Spacer
62.Gasket
TSB Revision

23-68
AUTOMATIC TRANSAXLE - Transaxle Assembl,y
(8) Remove the oil pan, magnet, and gasket.
(9) Remove the oil screen.
(10)Remove the ten valve body mounting bolts.
(11 IRemove the oil temperature sensor holder and remove the
oil temperature sensor harness from the clamp.
(12)Press the solenoid valve harness grommet claw to push the
grommet into the case; then, remove the valve body
assembly.
(13)Pull off the oil temperature sensor.
(14)Remove the parking roller support.
TSB RevisionI

AUTOMATIC TRANSAXLE - Transaxle Assembly23-89
(58)lnstall the detent assembly.
(59)Fit a new O-ring to the manual control shaft assembly, apply’ATF, and insert it into the transaxle case.
(6O)Align the groove in manual control shaft with the set screw
hole and install the set screw.~(61)Mount the parking roller support.
(62)lnstall the oil temperature sensor into the case.
(63)Fit the O-ring into the O-ring groove in the top surface of
valve body assembly.I
TSB Revision

AUTOMATIC TRANSAXLE - Transaxle Assembly
.AInhibitor switch
(64)Replace the solenoid valve harness grommet O-ring with a
new one.
(65)Pass the solenoid valve connector into the hole in transaxle
case from the inside.
(66)Press the solenoid valve harness grommet into the case
hole.(67)Fitting the detent plate pin into the groove in manual valve,
temporarily secure the valve body. Then, install the oil
temperature sensor and holder and tighten bolts to speci-
fication.
Bolt A = 18 mm
(.71 in.)
Bolt B = 25 mm
(.98 in.)
Bolt C = 40 mm (1.57 in.)
Caution
Secure the solenoid valve and oil temperature sensor
harnesses as shown.
(68)lnstaII the oil screen.
c(69)Mount the magnet to oil pan and install the oil pan
(70)lnstall the inhibitor switch and manual control lever.
(71
)Install the speedometer gear assembly.
TSB Revision

26-6FRONT AXLE - Hub and Knuckle
HUB AND KNUCKLE
REMOVAL AND INSTALLATION
M261A- -
90
- 105 Nm
7 - 76 fubs.
T\
60-72Nm2001260 Nm
43 - 52 ft.‘bs.145 - 188 ftlbs.b
Ibs.UN002929Nm
200
- 260 Nm145- 188 ftlbs.llFO026
Removal steps
4*1. Front speed sensor connection
l *2. Cotter pin4* l +3. Drive shaft nut4*4. Caliper assembly5.Brake disc6. Front hub unit bearing7.Dust shield4*8. Lower arm ball joint connection
4*4*
4*
9.Cotterpin10. Tie rod end connection
11. Drive shaft
12. Front strut mounting bolt
13. Hub and knuckle14.Hub
NOTE*: Anti-lock braking system
TSB Revision1

FRONT AXLE - Hub and Knuckle26-7MB990998-01MB990635-01
II
I1 lA0286 1
SERVICE POINTS OF REMOVALM2618AH
1. DISCONNECTION OF FRONT SPEED SENSORRemove the mounting bolts which hold the speed sensor
bracket to the knuckle, and then remove the speed sensor.
Caution
Be careful when handling the pole piece at the tip of the
speed sensor and the toothed edge of the rotor so asnot to damage them by striking against other parts.
3. REMOVAL OF DRIVE SHAFT NUT
Loosen the drive shaft nut while the vehicle is on the floor
with the brakes applied.
Caution
Do not apply vehicle load to the wheel bearing loosingthe drive shaft nut. If, however, vehicle load must be
applied to the bearing in moving the vehicle, temporari-
ly secure the wheel bearing by using the special tools,
MB990998-01, etc.
4. REMOVAL OF CALIPER ASSEMBLY
Remove the caliper assembly and suspend it with wires.
8. DISCONNECTION OF LOWER ARM BALL JOINT
Using the special tool, disconnect the lower arm ball joint
from the knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
IO. DISCONNECTION OF TIE ROD ENDUsing the special tool, disconnect the tie rod end from the
knuckle.
Caution
1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
11. REMOVAL OF DRIVE SHAFTUse the special tool to push out the drive shaft from the
front hub.
14. REMOVAL OF HUBIn the case of AWD-vehicles with A.B.S., take care not to
damage the rotor for A.B.S. installed to the B.J. outer race
when removing the hub.
TSB Revision

27-4
REAR AXLE - Rear Axle Hub
REAR AXLE HUB
REMOVAL AND INSTALLATION
M27MA- -
50-60Nm36 - 43 ftlbs.
200-260Nm145-188ftibs.Removal steps
4*4*1. Rear speed sensor 2. Calioer assemblv3.Brakedisc4. Hubcap
l *5. Wheel bearing nut4’6. Tongued washer7. Rear hub assembly4*8. Rear rotor 9. Rear hub unit bearing
Caution
Rear hub unit bearing cannot be disassembled.
llN0018
Pole p&e14NOlO-7
SERVICE POINTS OF REMOVALM27MBAC
1.REMOVAL OF REAR SPEED SENSOR
Caution
Be careful when handling the pole piece at the tip of thespeed sensor and the toothed edge of the rotor so as
not to damage them by striking against other parts.
2. REMOVAL OF CALIPER ASSEMBLY
Remove the caliper assembly and suspend it with a piece of
wire.
8. REMOVAL OF REAR ROTOR
CautionCare must be taken not to scratch or scar the rotor’s
toothed surface, and not to drop it.
If the rotor’s toothed surface is chipped or the rotor is
deformed, it might not be able to accurately sense the
wheel rotation speed and the system as a result mightnot perform normally.
14NOO99ITSB Revision

I’REAR AXLE
- Axle Shaft
AXLE SHAFT
REMOVAL AND INSTALLATION27-15M27HA- -
i
/
i55-65 Nm
QO - 47 ftlbs.
Iq y 6
50-60Nm
36-4?R.‘bs-
12 Nm9 ft.lbs.
/
190 Nm137 ft.lbs.
260 - 300 Nm188-217ftlbs.
Removal steps
l *1. Rear speed sensora*2. Brake caliper assembly
3. Brake disc
4. Drive shaft mounting nut
+I) l *5. Self-locking nut
6. Washer
7. Companion flange
l *8. Axle shaft assembly+* l +9. Rear rotor

+* l + 10. Outer bearinga* l a 11. Dust shieldl a 12. Dust shield13. Axle shaftl * ** 14. Oil seall * I)+ 15. Inner bearing
/llN0021
llA0325 IllA026~
SERVICE POINTS OF REMOVALM27HBAQ
1.REMOVAL OF REAR SPEED SENSOR
Caution
Be cautious to ensure that the tip of the pole piece doesnot come in contact with other parts when removing
the speed sensor.2. REMOVAL OF BRAKE CALIPER ASSEMBLY
Remove the brake caliper assembly and suspend it with apiece of wire.
1 TSB Revision