1991 MITSUBISHI 3000GT height

00-20GENERAL - Special Handling Instructions for AWD Models
14A019fOOPOO38
BalancingmachineOOA0046
Pick-up stand
OOA0024
I
FRONT WHEEL MEASUREMENTS1. Place the front wheels on the brake tester.
2. Perform the brake test.
CautionThe rear wheels should remain on the ground.
3.If the brake dragging force exceeds the specified value, jack
up the vehicle and manually rotate each wheel to check the
rotation condition of each wheel.
NOTEIf the brake dragging force exceeds the specified value, the
cause may be the effect of the viscous coupling’s dragging
force, so jack up the front wheels and check the rotation
condition of the wheels in this state for no effect by the
viscous coupling’s dragging force.
REAR WHEEL MEASUREMENTSAfter placing the rear wheels on the brake tester, follow the
same procedures as for the front wheel measurements.
WHEEL BALANCE
FRONT WHEEL MEASUREMENTS‘d
1. Jack up the rear wheels, and place an axle stand at the
designated part of the side sill.
2. Jack up the front wheels and set a pick-up stand and
balancing machine in place.
Caution
1.Set so that the front and rear of the vehicle are at
the same height.
2. Release the parking brake.
3. Rotate each wheel manually and check to be sure
that there is no dragging.
3. Use the engine to drive the tires, and then make the
measurements.
Caution
1.If an error is indicated in the state of engine drive,
motor drive can be used concurrently.
2. Do not operate the clutch suddenly, or increase or
reduce speed suddenly during the work.
REAR WHEEL MEASUREMENTS1. Jack up the front wheels, and place an axle stand at the
designated part of the side sill.
2. Jack up the rear wheels, and then, after setting a pick-up
stand and balancing machine in place; follow the same
procedure as for front wheel measurements.
\
\L)
TSB RevisionSPECIAL HANDLING INSTRUCTIONS
FOR AWD MODELSMOOUAACBRAKE TEST
‘dIn order to stabilize the viscous coupling’s dragging force, the
brake test should always be conducted after the speedometer
test.

GENERAL - General Data and Specifications
GENERAL DATA AND SPECIFICATIONS
00-21
MOOHA- -
c-i----J---i!--8GENERALSPECIFICATIONS
Vehicle dimensionsmm (in.)
Overall length
1
Overall width2
Overall height3
Wheelbase4
Tread
Front5
Rear6
OverhangFront7
Rear8
Minimum running groundclearance9
Angle of approachdegrees10
Angle of departuredegrees11
Vehicle weightkg (tbs.)
Curb weights
MIT
AI-T
Gross vehicle weight rating
Gross axle weight rating
Front
Rear
Seating capacity
Engine
Model No.
Piston displacementcm” (cu.in.)
3000GT
(Non-Turbo)
4,545(178.9)
1,840(72.4)
1,285(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145(5.7)
12.2”
16.9”
1,455 (3,208)
1,495 (3,296)
1,925 (4,244)
1,100 (2,425)
850 (1.874)
4
6G72-(DOHC)
2,972 (181.4)3000GT SL
(Non-Turbo)
4,545(178.9)
1,840(72.4)
1,285
(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145(5.7)
12.2”
16.9”
1,520 (3,351)
1,560 (3,439)
1,925 (4.244)
1,100 (2,425)
850 (1,874)
4
6G72-(DOHC) -
2,972 (181.4)
+64
OOFO015
3000GT VR-4
(Turbo)
4,545(I 78.9)
1,840
(72.4)
1,285(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145 (5.7)
12.2”
16.9”
1,710 (3.770)1,720 (3,792)“’
-
2,050 (4.519)
1,110 (2,447)940
(2,072)
4
6G72-(DOHC)
2,972 (181.4)
NOTE“I : <4ws>
1 TSB Revision

L’
LENGINE
- Specifications11-5
Items
Standard value
Limit
Cylinder head
Overall height
mm (in.)
132 (5.20)-0.2 (-,008)’
Flatness of gasket surface
mm (in.)Max. 0.03 l.0012)0.2 (.008)
Oversize rework dimension of valveseat hole
mm (in.)
Intake
0.3 f.012) O.S.36.300 - 36.325 (1.4291 - 1.4301)
0.6 l.024) O.S.36.600 - 36.625 (1.4409 - 1.4419)
Exhaust 0.3
l.012) O.S.33.300 - 33.325 (1.31 IO - 1.3120)
0.6 (.024) O.S.33.600 - 33.625 (1.3228 - 1.3238)
Oversize rework dimension of valveseat hole depth
mm (in.)
Intake
0.3 l.012) O.S.7.5 - 7.7 (.295 - ,303)
0.6 t.024) O.S.
7.8 - 8.0 (.307 - ,315)
Exhaust 0.3 t.012) O.S.7.9-8.1 (.311 - ,319)
0.6 (.024) O.S.
8.2 - 8.4 (.323 - .331)
Oversize rework of valve guide hole
(both intake and exhaust)mm (in.)
0.05 f.002) 0,s.13.050- 13.068(.5138-.5145)
0.25 (.OlO) O.S.13.250- 13.268 (.5217- .5224)
0.50 (.020) 0,s.13.500 - 13.518 (.5315 - .5322)
Samshaft
Cam heightmm (in.)
Intake
35.49 (I .3972)34.99 (1.3776)
Exhaust
35.20 (1.3858)
34.70 (1.3661)
Journal O.D.
mm (in.)
26 (1.02)
Bearing oil clearance
mm (in.)0.05 - 0.09 f.0020 - .0035)
Jalve
Valve lengthmm (in.)
Intake
106.3 (4.185)
Exhaust
105.4 (4.150)
Stem O.D.mm (in.)
Intake
6.6 (.260)
Exhaust6.6 i.260)
Face angle
45 - 45.5”Thick;;ss,yf
valve head (Margin)
Intake
1 .o (.039)0.5 (.019)
Exhaust1.5 (.059)1 .o (.039)
Clearance (Valve stem to guide)
mm (in.)
Intake
0.02 - 0.05 (.0008 - .0020)0.10 l.0039)
Exhaust0.05 - 0.09 l.0020 - .0035)0.12 i.0047)
* Limit must be -0.2 mm (--.008 in.) combined with amount of grinding of cylinder block gasket surface.
TSB Revision

11-6ENGINE - Specifications
Items
Valve guide
Lengthmm (in.)
Intake
Exhaust
Service sizemm (in.)Standard value
45.5 (1.791)
50.5 (1.988)
0.05 f.002). 0.25 (.OlO),0.50 f.020) OversizeLimit
Valve seat
Width of seat contactmm (in.)0.9 - 1.3 (.035 - ,051)
Seat angle44 - 44.5”
Valve spring
Free lengthmm (in.)46.9 (1.846)45.9 (1.807)
LoadN (Ibs.)280 (62) at installed height
Installed heightmm (in.)37.9 (1.492)38.9 (1.531)
Squareness1
Less than 2”4”
Cylinder block
Cylinder boremm (in.)
91 .I0
(3.5866)
Out-of-roundness and taper of cylinderLess than 0.02 i.0008)
boremm (in.)
Flatness of gasket surfacemm (in.)
Less than 0.05 t.0020)0.10 (.0039)
Piston0.D mm (in.)
91 .I0 (3.5866)
Clearance (Piston to cylinder)mm (in.)
0.03 - 0.05 (.0012 - .0020)
Ring groove widthmm (in.)
No. 11.2 (.047)
No. 21.5 f.059)
Oil
3.0 (.I 18)
Service sizemm (in.)
0.25 LO1 0),0.50 (.020),0.75 (.030), 1 .oo l.039)Oversize
Piston ring
Side clearancemm (in.)
No. 1
No. 2
End gap
mm (in.)
No. 1
No. 2
Oil ring side railmm (in.)
Service sizemm (in.)
0.03 - 0.07 (.0012 - .0028)
0.02 - 0.06 l.0008 - .0024)
0.30 - 0.45 (.0118 - .0177)
0.45 - 0.60 (.0177 - .0236)
0.20 - 0.60 (.0079 - .0236)
0.25 (.OlO), 0.50 (.020),0.75 (.030), 1 .oo (.039)Oversize
0.1 (.004)
0.1 (.004)
0.8 i.031)
0.8 l.031)
1 .o (.039)
Connecting rod
Bendmm (in.)
Twist
mm (in.)
Big end to thrust clearancemm (in.)
Piston pin press-in load
N (Ibs.)
0.05 i.0020) or less
0.1 (0.004) or less
0.10 - 0.25 (.0039 - .0098)
7,500 - 17,500 (1,686 - 3,934)
0.4 l.016)
1 TSB Revision

11-32ENGINE - Rocker Arm and Camshaft
r
I
/7EN024E
Small wire
8ENOO58
Identification mark(stamped on hexagon section)
7EN0249
Front sideINSPECTION
MllZCAB
CAMSHAFTMeasure cam height (longer diameter of the cam). If it exceeds
the limit, replace the camshaft.
Standard value:
Intake side
35.49 mm (1.3972 in.)
Exhaust side
35.20 mm (1.3858 in.)
Limit:
Intake side
34.99 mm (1.3776 in.)
Exhaust side
34.70 mm (1.3661 in.)SERVICE POINTS OF INSTALLATION
MllZDAK
11. INSTALLATION OF LASH ADJUSTER
(1) Immerse the lash adjuster in clean diesel fuel.
(2) Using a small wire, move the plunger up and down 4 or
5 times while pushing down lightly in the check ball in
order to bleed out the air.
(3) Install the lash adjuster to the cylinder head.
9. INSTALLATION OF CAMSHAFT
(1) Turn the crankshaft to bring No.1 cylinder to the top
dead center.
(2) Check that the rocker arm is installed correctly on the
lash adjuster and valve.
(3) Install the camshaft noting the identification mark
(stamped on the hexagon sectioned).
Identification mark: Intake sideV
Exhaust side C
(4) Install the camshafts with their dowel pins positioned
as shown in the illustration.
Rear side ,
Approx. 100”
Pl
Frontm&k
M
0
/
Cap No
TSB Revision
Identificationmark
7EN03168. 7. 6. 4. 2. INSTALLATION OF BEARING CAPS
(1) Install noting the identification mark and cap No. No.2, 3
and 4 bearing caps bear the front mark. Install these
caps with the mark lined up with the front mark on the
cylinder head.
Identification mark: Intake side
IExhaust side E

COOLING - Thermostat14-11
THERMOSTATMlbGB- -
iREMOVAL AND INSTALLATION
L
Pre-removal and Post-installation
l Draining and Supplying of the
(Refer to GROUP 00
- Maintenance
Removal steps
1. Air hose A +a2. Air intake hose A
3. Air intake hose
4. Connection of radiator lower hose
5. Water inlet fitting
6. Gasketl a 7. Thermostat
OlFOO37
7cooo43l
Fullyclosed j
04N0004
INSPECTIONM14GDALl Check that valve closes tightly at room temperature.
l Check for defects or damage.
l Check for rust or encrustation on valve. Remove if any.
l Immerse thermostat in container of water. Stir to raise
water temperature and check that thermostat opening
valve temperature and the temperature with valve fully
open [valve lift-over
10 mm (39 in.)] are at the standard
value.
Standard value:
Opening valve temperature
Full-open temperature
NOTE76.5%
(‘170°F)
90°C ( 194°F)Measure valve height when fully closed. Calculate lift by
measuring the height when fully open.
-
TSB Revision

CLUTCH - Specifications
SPECIFICATIONSI
GENERAL SPECIFICATIONSMZlCA--i
Type
Facing diameterSingle dry disc type
Single dry disc type
Diaphragmspring strap
SERVICE SPECIFICATIONS
terns
Standard value
Clutch pedal heightmm (in.)
Clutch pedal strokemm (in.)
Amount of clutch pedal return from full pedal stroke
position to where operating sound of interlock switch
is producedmm (in.)
Clutch pedal
clevis pin playmm (in.)
Clutch pedaLfree playmm (in.)
Distance between the clutch pedal and the firewall when
the clutch is disengagedmm (in.)
Specifications
177 - 182 (6.97 - 7.17)
160 (6.29)
IO-15(.394-,591)
I-3 (.04-.12)
6-13(.24-.51)
55 (2.2) or more
Booster push rod to master cylinder piston clearance
0.21 - 0.46 (.0082 - .0181)mm (in.)
Vacuum hose insertion distancemm (in.) 20 - 25 (0.8 - 1 .O)
Limit
Facing rivet sinkmm (in.)0.3 l.012)
Diaphragm spring end height differencemm (in.)0.5 (.020)
1 TSB RevisionI

CLUTCH - Service Adjustment Procedures21-5
Clutch pedal height
08YO41
auto-cruise control
L-l
\ \ 0Cl;tchswitch
\ \08F0010
Clutch pedal stroke
Lock nut
08F005414110052
SERVICE ADJUSTMENT PROCEDURES
CLUTCH PEDAL INSPECTION AND ADJUSTMENTMZlFAAP
1.Measure the clutch pedal height (from the face of the pedal
pad to the firewall).
Standard value: 177
- 182 mm (6.97 - 7.17 in.)
If the clutch pedal height is not within the standard value
range, adjust as follows:
For vehicles without auto-cruise control system, turn and
adjust the bolt so that the pedal height is the standard
value, and then secure by tightening the lock nut to the
specified torque.
Vehicles with auto-cruise control system, disconnect the
clutch switch connector and turn the switch for standard
clutch pedal height. Tighten the lock nut to the specified
torque.
Specified torque: 13 Nm (9
ft.lbs.)
NOTEWhen the pedal height is lower than the standard value,
loosen the bolt or clutch switch, and then turn the push rod
to make the adjustment. After making the adjustment,
tighten the bolt or clutch switch to reach the pedal stopper,
and then lock with the lock nut.
2. Measure the clutch pedal stroke.
Standard value: 160 mm (6.29 in.) or more
If the clutch pedal stroke deviates from the standard value,
turn the push rod to adjust the stroke.
3. Return the clutch pedal gradually from its full-stroke
position to measure amount of the return made by the
pedal
u,ntil the interlock switch makes an operating sound.
Standard value: 10
- 15 mm (.394 - .591 in.)
If the amount of pedal return deviates from the standard
value, adjust it by loosening the lock nut and turning the
interlock switch.
TSB Revision