1991 MITSUBISHI 3000GT clock

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
dir J
bag module, clock spring, interconnecting wiring. Other SRS-related comp\
onents (that may have to be
(*).
The Supplemental Restraint System (SRSI-related components are shown in the following MASTER TABLE
OF CONTENTS. Be sure to carefully read and understand the WARNING below \
before proceeding.
Group number
22.23
32
36
42
52A
Group nameSRS-related components
FUELCRUISE CONTROL SYSTEM/ P.13-185
MANUALTRANSAXLE.TRANSAXLE CONTROLAUTOMATIC TRANSAXLE
POWER PLANT MOUNTRIGHT MEMBER, LEFT MEMBER AND CROSSMEMBERP.32-6
ELECTRONIC CONTROLSUSPENSION’STEERING ANGULAR VELOCITY SENSORP.33B-19
PARKING BRAKESPARKING BRAKE LEVER AND PARKiNG BRAKE CABLE/ P.36~5I
STEERING/POWER STEERING GEAR BOX/ P.37A-17
/STEERING WHEEL AND SHAFTj P.37A-13
BODY
INTERIOR
FENDER
FLOOR CONSOLE/ P.52A-11
FRONT SEAT
INSTRUMENT PANEL
P52A-18
P.52A-8
CHASSIS ELECTRICAL
SEAT BELT
COLUMN SWITCH
HORN SWITCH
IGNITION SWITCH
P.52A-25
P.54-73
P.54-78
1 P.54-6
RADIO REMOTE-CONTROL/ P.54.110
HEATER, AIR CONDITIONERAIR-CONDITIONER CONTROL PANELAND VENTILATIONAIR-CONDITIONER CONTROL UNITP.55-56
/DAMPER CONTROL MOTOR ASSEMBLYI
/HEATER CONTROL ASSEMBLY1 P.55-18I
HEATER UNIT.1 P.55-22
WARNING!
VENTILATORS (INSTRUMENT PANEL)P.55-36
(1) Improper service or maintenance of any component of the SRS, or an\
y SRSrelated component,
can lead to personal injury or death to service personnel (from inadver\
tent firing of the air bag) or
to the driver (from rendering the SRS inoperative).
(260°F) in baking or in
drying after painting, remove the SRS components (air bag module, SRS d\
iagnosis unit, front
perfarmed
only at an authorized MITSUBISHI dealer.
52B
- Supplemental Restraint System (SRS), before beginning any service or m\
aintenance of any
component of the SRS or any SRS-related component.
1 TSB RevisionI

II-12ENGINE - Service Adjustment Procedures-
r
AdJl
bolt
Alternator wllev
haft
Fixing nutOlFOOO8
Alternator pulley
Adjusting bolt
/Crankshaftpulley
Air contionercompressorpulleyw Tension pulleyFlxtng nutOlN007.
Crankshaft pulleyOlN007TENSION ADJUSTMENT OF THE ALTERNATOR DRIVE
BELT
I(1) Remove front under cover panel ’
aero> (Refer to GROUP 51 - Aero Parts.).\\
3 ’
(2) Remove under covers (front L.H., side L.H.).
(3) Loosen tension pulley fixing nut.
(4) Adjust belt deflection with adjusting bolt.
(5) Tighten fixing bolt.
(6) Run the engine one time or more.
(7) Check the belt tension. Readjust, if necessary.
(8) Install under covers.
DEFLECTION ADJUSTMENT OF THE ALTERNATOR AND
AIR CONDITIONER COMPRESSOR DRIVE BELT with air conditioner>
(1) Use straight handle box wrench to loosen tension pulley
fixing nut.
(2) Adjust belt deflection with adjusting bolt.
(3) Use straight handle box wrench to tighten fixing nut.
(4) Run the engine one time or more.
(5) Check the belt deflection. Readjust, if necessary.
DEFLECTION ADJUSTMENT OF POWER STEERING PUMP
DRIVE BELT(1) Insert an extension bar (insertion depth 12.7 mm), etc. into
the opening at the end of the tension pulley bracket.
(2) Loosen the tension pulley fixing bolts in the order of B and
(3)
iove the extension bar installed to the tension pulley in the‘LJdirection of arrow to adjust the belt tension.
(4) Tighten the tension pulley fixing bolts in the order of A and
8.Tightening torque: 35
- 50 Nm (25 - 36 ftlbs,)(5) Give the crankshaft two turns in normal direction (clock-
wise) to run in the belt.
(6) Check the belt deflection. Readjust, if necessary.
1 TSB Revision

ENGINE - Service Adiustment ProceduresII-13
I_ ianltion tlminaI!H Connector for Igdpstment 6rown)
4tll II -7FUO9371IGNITION TIMING ADJUSTMENTMllFLAF
(1) The vehicle should be prepared as follows before the
inspection and adjustment.
lEngine coolant temperature: 80 - 95°C (176 - 205°F)
l Lights, electric cooling fan and accessories: OFF
l Transaxle: neutral
(P for A/T)l Steering wheel: neutral position
(2) Insert a paper clip to the connector, and connect a
tachometer to the paper clip.
NOTEDo not use the Multi-use tester.
If tested with the Multi-use tester connected to the
diagnosis connector, the ignition timing will not be the basic
timing but be ordinary timing.
(3) Set the timing light.
(4) Start the engine and run at idle.
(5) Check curb idle speed.
Curb idle speed: 700
f 100 rpm
NOTEThe engine speed indicated is a third of actual speed. In
other words, the reading of the tachometer times 3 is actual
speed.
(6) Turn OFF the ignition switch.
(7) Using a jumper wire, ground the ignition timing adjusting
terminal.
NOTEGrounding this terminal sets the engine to the basic ignition
timing.
\(8) Start the engine and run at idle.
(9) Check basic ignition timing.
Basic ignition timing: 5” BTDC
k 2”
(10)lf not within the standard value range, loosen the crank
angle sensor mounting nut and adjust by turning the crank
angle sensor. Turning it to the counterclockwise retards
timing, and to the clockwise advances it.
(1 l)After adjustment, tighten mounting nut taking care not to
move the crank angle sensor.
(12)Turn OFF the ignition switch.
(13)Disconnect the jumper wire connected at step (7).
(14)Start and run the engine at curb idle speed.
1 TSB Revision

11-28ENGINE - Timing Belt
Tlmlng mark01 N009E
A : :y,y;i;,$yi *&:;.~:;>
Exhaust valveside
*
/’*
120"* -1"
(*
6
7.^^^J‘c;Y
1zv w**
Intake valveside
Front bank
* : Approx. 35” o1 N0, og
Rockercoverslde
Exhaust valveside
Front bank
t~mng markOlNOlO
12. INSTALLATION OF TIMING BELT
(1) Align the timing marks on the respective sprockets.
In case of the camshaft sprockets in the front bank,
I~
proceed as follows:@ Install the crankshaft pulley. Shift the timing mark
on the crankshaft sprocket by three teeth to lower
the piston in No. 1 cylinder slightly from the top
dead center on compression stroke.
CautionTurning the camshaft sprocket with the piston
in No. 1 cylinder located at TDC on compression
stroke may cause the valves to interfere with the
piston.@ Make sure that the timing marks on the camshaft
sprockets for intake and exhaust valves are not
within the range A in the illustration at left.
If the timing mark is within range A, turn the
camshaft sprocket to move the timing mark to the
area closest to the range A.
CautionIn range A, the cam lobe on the camshaft lifts
the valve through the rocker arm and the
camshaft sprocket is apt to rotate by reaction
force of the valve spring. Therefore, be careful
not to have the finger pinched between the
sprockets.@ Turn the camshaft sprocket for either the intake or
exhaust valve to locate the timing mark as shown in
\the illustration at left. Then turn the other crankshaft
to locate the timing mark-as shown in the illustration
at left.
CautionIf the intake and exhaust valves of the same
cylinder lift simultaneously, interference with
each other may result. Therefore, turn the intake
valve camshaft sprocket and the exhaust valve
camshaft alternately.@ Turn the camshaft sprocket clockwise to align the
timing marks.
If the camshaft sprocket has been turned excessive-
ly, turn it counterclockwise to align the timing
marks.
TSB Revision
.@ Align the timing mark of the crankshaft sprocket.
NOTEShift the timing mark of the crankshaft sprocket one
teeth in counterclockwise direction to facilitate belt
installation.

ENGINE - Timing Belt11-29
OlN004t
& Pin hole
nilnq
8(2) Using paper clips, install the timing belt in the following
order with care not to allow the belt to slack.@ Exhaust camshaft sprocket (front bank side)
+ @
Intake camshaft sprocket (front bank side)
-+ @Waterpump pulley
+ @ Intake camshaft sprocket (rear bank
side)
+ @ Exhaust camshaft sprocket + @ Idler pulley
-+ @ Crankshaft sprocket + @ Tensioner pulley
NOTESince the camshaft sprockets turn easily, secure them
with box wrenches to install the timing belt.
Caution1. Be careful, the camshaft is turned by the reac-
tion of valve spring.
2.If the timing belt is reused, install it so that thearrow marks made at removal are in the direc-
tion of rotation.
(3) Turn the tensioner pulley so that its pin holes are
located above the center bolt. Then, press the tensioner
pulley against the timing belt and, at the same time,
temporarily tighten the center bolt.
(4) Check that the timing marks on all sprockets are aligned
properly.
(5) Remove the four clips.
. ADJUSTMENT OF TIMING BELT TENSION
(1) Rotate the crankshaft
114 turn counterclockwise, then
rotate it clockwise until the timing marks are aligned.
(2) Loosen the center bolt on the tensioner pulley. Using
the special tool and torque wrench, apply tensioning
torque to the timing belt and, at the same time, tighten
the center bolt to specification.
Specified torque:
10 Nm (7 ftlbs.)
[Timing belt tensioning torque]
Caution
When tightening the center bolt, make sure that thetensioner pulley is not rotated together.
(3) Remove the set pin from the auto tensioner. At this
time, make sure that the set pin can be easily removed.
(4) Rotate the crankshaft two turns clockwise and leave it
as is for five minutes or more. Then, check again that
the set pin can be easily removed from, and installed to,
the auto tensioner.
NOTEEven if the set pin cannot be easily inserted, the auto
tensioner is normal if its rod protrusion is within
specification.
Standard value (A): 3.8
- 4.5 mm (.I49 - .I77 in.)
If the protrusion is out of specification, repeat steps (1)
to (4).
(5) Check again that timing marks on all sprockets are
aligned properly.
TSB Revision

FUEL
SYSTEM
CONTENTSM13AA- _
CRUISE CONTROL SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . .158SPECIFICATIONS. . . . . . . .._._....................................................155
CRUISE CONTROL SYSTEM*................................................185
SERVICE ADJUSTMENT PROCEDURES............................178
Cruise Control Cables Inspection and Adjustment........178Cruise Control SystemInspection....................................179individual Parts Inspection....................................................181
SPECIAL TOOLS........................................................................159
SPECIFICATIONS....................................................................158
General Specifications........................................................158Service Specifications........................................................158
TROUBLESHOOTING............................................................159
Check Chart............................................................................163Harness and Components Layout....................................176Preliminary Inspection........................................................159Self-diagnosis Checking........................................................172Troubleshooting Quick Reference Chart............................159
ENGINE CONTROL............................................155
ENGINE CONTROL................................................................157
SERVICE ADJUSTMENT PROCEDURES............................156
Accelerator Cable Inspection and Adjustment................156Accelerator Switch Inspection and Adjustment................156
Service Specifications........................................................
155
TROUBLESHOOTING............................................................
155
Accelerator Cable and Accelerator Pedal........................155
FUEL SYSTEM....................................................3
DETONATION SENSOR........................................................154
FUEL FILTER............................................................................
153
FUEL LINE AND VAPOR LINE................................................151
FUEL PUMP AND FUEL GAUGE UNIT ASSEMBLYAND OVERFILL LIMITER (TWO-WAY VALVE)................149
FUEL TANK.................................................................................146
GENERAL INFORMATION
....................................................
3
MPI System Diagram............................................................3
INJECTOR................................................................................141
ON-VEHICLE INSPECTION OF MPI COMPONENTS........36
Active Exhaust Control Unit ............................130Air Conditioner Switch and Power Relay............................82Air Flow Sensor....................................................................54Anti-lock Brake Signal ........................................133Barometric Pressure Sensor................................................60CONTINUED ON NEXT PAGE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP
528 -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

FUEL SYSTEM - Service Adjustment Procedures
(3) Insert a 0.65-mm-thick feeler gauge between the fixed SASand throttle lever.
Terminal @
(sensor output)zensor g&nd)MB991348
1
(4) Loosen the throttle position sensor mounting bolts and turnthe TPS body fully counterclockwise.
(5) In this condition, check that there is continuity across
terminals
@ and @.
(6) Slowly turn the throttle position sensor clockwise until you
find a point at which there is no continuity across terminals
@ and 0. Then, tighten the throttle position sensor
mounting bolt securely.(7) Connect the throttle position sensor connector.
(8) When using the multi-use tester, connect it to the diagnosis
connector.
(9) When not using the multi-use tester, proceed as follows:
@ Disconnect the throttle position sensor connectors andconnect the special tool, Test Harness Set, between
the disconnected connectors.
@ Connect a digital voltmeter between the throttle posi-
tion sensor terminal @ (sensor output) and teminal @
(sensor ground).
(lO)Turn the ignition switch ON (but do not start the engine).
(IlKheck the throttle position sensor output voltage.
When using the multi-use tester, select item No. 14 and
read the throttle position sensor output voltage.
Standard value: 400 - 1,000 mV
(12)lf the voltage is out of specification, check the throttle
position sensor and associated harnesses.
(13)Remove the feeler gauge.
(14)Turn the ignition switch OFF.
TSB Revision
1

FUEL SYSTEM - Service Adjustment Procedures13-35
ADJUSTMENT OF FIXED SASMlJFlDC
NOTE
(1) The fixed SAS has been factory-adjusted. Never attempt tomove it.
(2) Should it be out of proper adjustment, adjust by following
the procedure given below.(I) Sufficiently slacken the accelerator cable.
(2) Loosen the lock nut on the fixed SAS.
(3) Sufficiently loosen the fixed SAS by turning it counterclock-wise to fully close the throttle valve.
(4) Tighten the fixed SAS slowly to find a point at which it
contacts the throttle lever (where the throttle valve starts
opening). From that point, tighten the fixed SAS further 1 l/4
turns.
(5) Holding the fixed SAS to prevent it from turning, tighten thelock nut securely.
(6) Adjust the accelerator cable tension. (Refer to
P.13-156.)(7) Adjust the basic idle speed. (Refer to
P.13-31.)
(8) Adjust the idle position switch and throttle position sensor
(TPS). (Refer to P.13-33.)
1 TSB Revision