1991 MITSUBISHI 3000GT sensor

32-1
POWER PLANTMOUNT
CONTENTSMZAA- _
ENGINE MOUNTING........................................
3SPECIFICATIONS................................................2
ENGINE ROLL STOPPER
5Service Specifications....................................2....................................
TRANSAXLE MOUNTING................................4RIGHT MEMBER, LEFT MEMBER AND
CROSSMEMBER”................................................6TROUBLESHOOTING........................................2
SPECIAL TOOLSAbnormal Noise....................................................
2
Excessive Engine Wobble or Vibration
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

FRONT SUSPENSION - Strut Assembly33A-5
STRUT ASSEMBLY
IREMOVAL AND INSTALLATION
‘=Il Adjustment of Wheel Alignment
M33lA- *
6
45 Nm
2
33 ft.lbs.4!
AI$
c3liI7 // ;I jI ’II ;/ ~I: /I /j j
1
-r11Ii /’ I--‘-
Removal steps
1. Brake hose tube clamo mountina bolt
2. Brake hose tube clam;-,3. Fr;;tSs;eed sensor clamp mountmg nut
4. Front speed sensor clamp
tABS>5. Strut lower mounting bolt
6. Strut upper mounting bolt
7. ECS connector

8. Cap
9. Strut assembly
1 TSB Revision

33B-1
ELECTRONIC
CONTROL
SUSPENSION
CONTENTSM33AA-B
CIRCUIT DIAGRAM
22SPECIAL TOOLS........................................................................3
................................................................
DAMPING FORCE CHANGEOVERSPECIFICATIONS....................................................................2
ACTUATOR................................................................................20General Specifications.......................................................2
ECS CONTROL UNIT................................................................21Service Specifications.......................................................3
ECS INDICATOR LIGHT............................................................20STEERING ANGULAR VELOCITYa .
ECS SWITCH............................................................................
19
G SENSOR................................................................................
19
POSITION DETECTION SWITCH............................................20
SERVICE ADJUSTMENT PROCEDURES
............................
12
On-Vehicle Inspection........................................................12
SENSOR*....................................................................................-IY
STOP LIGHT SWITCH............................................................20
THROTTLE POSITION SENSOR
............................................20
TROUBLESHOOTING............................................................4
VEHICLE SPEED SENSOR....................................................
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(I)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, aiir bagmodule, clock spring, interconnecting wiring.Other SRS-related components (that may have 1:o be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP
Ei2B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

33B-4ELECTRONIC CONTROL SUSPENSION (ECS) - TroubleshootingTROUBLESHOOTING
M33EAAE
QUICK REFERENCE CHART FOR TROUBLESHOOTING
SymptomsXS
indicator lightdoes not switch
TROUBLESHOOTING HINTS
“1. The G. sensor is a sensor associated with ride control (detecting pitching, bouncing and rough road). If itfails, therefore, ride control stops.
“2. A self diagnostic decision on the steering angular velocity sensor is made by the ECS control unit which
internally detects the voltages of the two sensor output lines connected to the ECS control unit to detectan open circuit in the signal line. When the signal line is short-circuited or when the power line is
open-circuited, however, it cannot be detected. In a situation where anti-roll control only stops, if
self-diagnosis code No. 21 is not on display, a short-circuited sensor output line or open-circuited sensorpower line is suspected.
“3. The vehicle speed sensor is a sensor associated with attitude controls (anti-dive, anti-squat) and steering
stability controls (anti-roll, high speed sensitive controls). If all these controls stop, therefore, trouble in the
sensor is suspected. The vehicle speed sensor is also in use for operation of the speedometer and for theother electronics controlled systems for the engine, automatic transaxle, etc.
“4. The sensor associated with anti-squat control is the throttle position sensor. The sensor is also used for
control of the engine and automatic transaxle. If the sensor fails, therefore, the check engine light in the
combination meter will light, and engine self-diagnosis code No. 14 will be output. In a situation whereanti-squat control only stops, therefore, if the check engine light does not light, defective wiring is
suspected between the ECS control unit and throttle position sensor.
TSB Revision

ELECTRONIC CONTROL SUSPENSION (ECS) - Troubleshooting33B-5
1When diagnosis code No. 11 is output
Disconnect G sensor connector.
No. 1 terminal voltage and continuity
between No. 3 terminal and ground
up to specification?
(Sensor power supply and ground)Standards:
No. 1 terminal5 V
No. 3 terminal
Continuity provided
IYes.-
-1Is continuity provided across the following
areas?
!
BetweenG sensor and ECS control unit
Between No. 1 terminal and No. 54
BetweenNo. 3 terminal and No. 57
,
Replace ECScontrol unit.Correct harness.
LNo
Continuity provided between No. 2) Correct harness.
terminal of G sensor and No. 61
terminal of ECS control unit?
I Yes
4N?Is trouble cleared by replaced G
sensor?bReplace ECS control unit.
I
Yes
EndTSB Revision

33B-6ELECTRONIC CONTROL SUSPENSION (ECS) - Troubleshooting
I I2When diagnosis code No. 21 is output, or when anti-roil control only stops.
Using MUT, check service data onthe steering angular velocity sensor.Check by entering simulated vehicle speed tosimulate anti-roll controls. (Refer to P.33B-16.)
+No
No. 2,3 and 4 terminal voltages up
to specification?Standard: 5 V
Yes
>Is continuity provided across the followingareas?Between steering angular velocity sensorand ECS control unit
Between No. 2 terminal and No.!Between No. 3 terminal and No.
Between No. 4 terminal and No.
Yes
Is trouble cleared by replacing
End
1 TSB RevisionI

ELECTRONIC CONTROL SUSPENSION (ECS) - Troubleshooting33B-7
3When diagnosis code No. 24 is output
1 i
Using MUT, check service data onvehicle speed sensor. Good?
YesjCheck by entering simulated vehicle speed from MUT
late high speed-sensitive control. (Refer to P.338-17.)
NoYesNo
151//Disconnect vehicle speed sensor con-nectar and check harness connector.j Good) /Replace ECS control unit.1
No. 1 terminal voltage and continuity
between No. 2 terminal and ground
up to specification?
(Sensor power supply and ground)Standards:No. 1 terminalBattery voltage
No. 2 terminalContinuity provided
Correct harness (between No. 1 terminal of vehicle
speed sensor and battery and between No. 2 terminal
of vehicle speed sensor and ground).
l-.-l
Yes
JI Nni1Is continuity provided between No. 3
terminal of vehicle speed sensor and
No. 53 terminal of ECS control unit?Correct harness.
1
Yes
Check vehicle speed sensor. (Refer
to P.33B-19.) Good?
No-Replace vehicle speed sensor.
Yes
IReplace ECS control unit.I
Using MUT, check service data onvehicle speed sensor.
No
late high speed-sensitive control. (Refer to P.33B-17.) Good!
Replace ECS control unit.
4t NoI1Is continuity provided between No.109 terminal of combination meter andNo. 53 terminal of ECS control unit?Correct harness.
Yes
Is continuity provided between No.
64 terminal of combination meter
and ground?
No
4
Correct harness.
Yes
Check vehicle speed sensor. (Refer
to P.33B-19.) Good?--+Replace vehicle speed sensor.
Yes
IReplace ECS control unit.I .
TSB Revision

ELECTRONIC CONTROL SUSPENSION (ECS) - Troubleshooting 33B-11
I I7
Anti-squat control only stops.III
L,
I
Using MUT, check service data onthrottle position sensor. Good?
Yes
rCheck by entering simulated vehicle speed from MUT to
simulate anti-squat control. (Refer to P.33B-16.) Good?!
1 Good1 ) Replace ECS control unit. 1
I
1I II
NoDoes check engine light illuminate?>Is continuity provided between No. 2 terminal of throttleposition sensor and No. 59 terminal of ECS controlunityII
Yes
i
Correct harness.
1Check throttle position sensor. (Refer to P.33B-20.) Good?III1
connector and check harness con-nector with ignition switch at ON.
No. 1 terminal voltage and continuityNo
Is
between No. 4 terminal and groundcontinuity provided across the following areas?
up to specification? (Sensor powerthrottle position sensor and engine control unit
No. 1 and 61 terminals
supply and ground)
No. 4 and 72 terminalsStandards:
INo. 1 terminal5 V
YesNo. 4 terminal
Continuity provided
Yes-1 1 Correct harnei:
”
Replace throttle position sensor.TSB Revision