1991 MITSUBISHI 3000GT wiper fluid

51-2
SPECIFICATIONSEXTERIOR
- Specifications
GENERAL SPECIFICATIONSMSlKB-
-\ IItems
Windshield wiper motorType
Speed control system
Braking system
rpm at load of 1 Nm (0.72
ft.lbs.)Low speed
High speed
Nominal torque
Nm (ft.lbs.)
Rear wiper motor
Motor type
Braking system
rpm at load of 0.6 Nm (0.43
ft.lbs.)Windshield wiper blade
Wiping angle
Driver’s side
Passenger’s side
Wiper blade length
mm (in.)
Driver’s side
Passenger’s side
Tear wiper blade
Wiping angle
Wiper blade lengthmm (in.)
Nindow washer motor and pump
Motor type
Pump type
Power consumption A
Time of continuous usesec.
With washer fluid
Empty operation
Nozzle jet pressure
kPa (psi)
Tank capacity
lit.
(qts.)
3ear window washer motor and pump
Motor type
Pump type
Power consumption A
Time of continuous use
sec.With washer fluid
Empty operation
Nozzle jet pressure
kPa (psi)
Tank capacity
lit. (qts.)Specifications
Ferrite-magnet type
Third brush system
Dynamic brake system
48
_+ 4
70
2 724(17)
Ferrite-magnet type
Dynamic braking system
38
+ 5
89”
91”
525 (20.7)
500 (19.7)87”
k 1.5”
550 (21.7)Direct current ferrite magnet type
Centrifugal type
3.8 or less
Max. 60
Max. 20
120 (17) or more
2.0
(2.1) or more
Direct current ferrite magnet type
Centrifugal type
3.8 or less
Max. 60
Max. 20
120 (17) or more
1.2 (1.3) or more
LJ
L/iTSB Revision

EXTERIOR - Windshield Wiper and Washer
MOVAL AND INSTALLATIONY5lK.JAR
I
‘LJ (
I
\
9Nm7 ft.lbs.
3emoval steps of linkage
I. Wiper blade
I)* 2. Wiper arm
3. Front deck garnish
4. Air inlet garnish
(RH)5. Hole cover
a*6. Wiper motor16FO103
7. Linkage
Removal steps of wiper motor
1. Wiper blade
l *2. Wiper arm
5. Hole cover
*I)6. Wiper motorRemoval steps of washer tank
8. Battery
9. Battery tray
10. Washer tank
11. Washer motor
12. Washer fluid level sensor
Removal of column switch (wiper and washer
switch)
15. Column switch (Refer to GROUP 54
-Column Switch.)
TSB RevisionRemoval steps of washer tube
8. Battery
9. Battery tray
13. Washer nozzle
14. Washer tube

51-34
EXTERIOR - Windshield Wiper and Washer
Connector B
-____1.310027lXN007t
1
dentification mark: AInspection of Wiper Relay (Built-in Column Switch)
(1) Check to ensure that there is continuity between terminals@ and @ and between the terminals @ and
@, and that
there is no continuity between terminals @ and
@.
(2) Connect the positive terminal of the battery to terminal @dand the negative terminal to terminal @ to check that the
battery voltage is available at terminal
@.INSPECTION OF WASHER MOTOR
(I) When the washer motor is inspected, make sure that it is
mounted on the washer tank and that the washer tank is
filled with water.
(2) Connect the battery as shown to check whether water is
pumped out.
INSPECTION OF WASHER FLUID LEVEL
,SENSOR
(1) Connect a circuit tester to the connector of the level sensor
as shown.
(2) Check that when the float is moved down, the circuit is
closed and that when the float is moved up, the circuit is
opened.
Front deck garnish18FO164SERVICE POINT OF INSTALLATION
2. INSTALLATION OF WIPER ARM
(1) The wiper arms, right and left, are different in shape.
Check the identification symbol.
(2) After the wiper blades have been set, install them in
such a way that the ends of the wiper blades will stop at
the specified positions (standard values).
Standard value: (A) 15
tz mm (.6 tf in.)
dTSB Revision