1987 MAZDA 626 air condition

IDLE-UP SYSTEM 4B
IDLE-UP SYSTEM
Dynamic chamber
To engine i
lN
Water thermo |ntake air sensor thermo
sensor
E/L control unit
-D
Solenoid A
From air ^^ flow meter ~
Engine
control
unit
Atmospheric pressure sensor
HI
f
"Solenoid B
UJ m
Solenoid C
u
Adjusting screw
| A/C
H-!
relay
IGN switch
-©n
To engine
control
unit
Magnetic clutch
fftf
tr Main relay
r © ©
P/S pressure switch
76G04B-043
Air Valve
This valve is constructed so that the gate valve is opened and closed by means of a bimetal strip and
heat coil. It acts as a fast idle mechanism by opening the gate valve to increase intake air by bypass-
ing the throttle valve while engine is cold, therefore engine speed is increased to shorten the warm
up period.
Air Bypass Solenoid Valve
This valve incorporates three solenoid valves. They operate according to the signal from the engine
control unit or A/C switch in order to achieve idling stability and the optimum idle speed.
The operating conditions of each solenoid valve are as shown below.
Solenoid valve Operating condition

A A/C operated
B Intake air temp, above 55°C (131 °F)
or
vehicle
at
above 1,000
m
(3,280
ft)

C P/S operated, E/L applied, intake
air
temp, above 55°C (131 °F), pressure regulator solenoid ON
or
vehicle
at
above 1,900
m
(6,232
ft)
4B-35

IDLE-UP SYSTEM 4B
TROUBLESHOOTING
Check the condition of the wiring harness and connectors before checking the sensors or switch.
Possible
cause
\ Page
Symptom
Air valve
Air bypass solenoid valve Engine control unit
terminal
Possible
cause
\ Page
Symptom
Air valve
Idle-up singal Adjustment
Engine control unit
terminal
Possible
cause
\ Page
Symptom
Air valve
Idle-up singal Adjustment
1S 20
Possible
cause
\ Page
Symptom 4B—38 4B—39 4B—40 4B—89 4B—90
Engine
stalls
While warming up
1 2 3 4 5
Engine
stalls After warming up
1 2 3 4

Rough Idle
While warming up
1 2 3 4 5
Rough Idle After warming up
1 2 3 4

High idle speed after warming up
1 2 3 4 5

Runs rough on deceleration
1 2 3 4

Afterburn in exhaust system
1 2 3 4 5

Fails emission test
1 2 3 4 5

76G04B-045
4B-37

FUEL SYSTEM 4B
COMPONENT DESCRIPTIONS
Component Function Remarks
Air flow meter
Detects amount
of
intake
air;

sends signal
to
engine control unit Intake
air
thermo sensor and fuel pump
switch
are
integrated

Atmospheric pressure sensor
Detects atmospheric pressure; sends sig-nal
to
engine control unit

Circuit opening relay
Voltage
for
fuel pump while engine running

Clutch switch
Detects in-gear condition; sends signal
to
engine control unit Switch
ON
when clutch pedal released

Engine control unit
Detects signals from input sensors and switches; controls injector operation

Fuel filter
Filters particles from fuel

Fuel pump
Provides fuel
to
injectors • Operates while engine running
• Installed
in
fuel tank

Idle switch
Detects when throttle valve fully closed;
sends signal
to
engine control unit
Installed
in
throttle sensor

Ignition coil (-) terminal
Detects engine speed; sends signal
to
engine control unit

Ignition switch (ST position)
Sends engine cranking signal
to
engine control unit

Inhibitor switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON in "N" or "P"
range

Injector
Injects fuel into intake port • Controlled
by
signals from engine control unit • High-ohmic injector

Intake air thermo sensor
Detects intake
air
temperature;
sends signal
to
engine control unit Installed
in air
flow meter

Main relay
Supplies electric current
to
injectors and engine control unit

Neutral switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON
in-gear

Oxygen sensor
Detects Oxygen concentration; sends sig-nal
to
engine control unit
Zirconia ceramic and platinum coating

Pressure regulator
Adjusts fuel pressure supplied
to
injectors

Pulsation damper
Absorbs fuel pulsation

Throttle sensor
Detects throttle valve opening angle; sends signal
to
engine control unit
Integrated idle switch

Water thermo sensor
Detects coolant temperature;
sends signal
to
engine control unit

Water thermo switch
Detects radiator coolant temperature; sends signal
to
engine control unit ON: above 17°C (63°F)

76G04B-058
4B—43

FUEL SYSTEM 4B
PRESSURE REGULATOR CONTROL SYSTEM
Water thermo sensor
*
Fuel
(To fuel tank)
76G04B-072
To prevent percolation of the fuel during idle after the engine is restarted, vacuum is cut to the pres-
sure regulator, increasing the fuel pressure.
Specified time: Approx. 120 sec.
Operating condition: Coolant temperature — above 70°C (158°F)
Intake air temperature — above 10°C (50°F)
4B—53

FUEL SYSTEM 4B
TROUBLESHOOTING
Check the condition of the wiring harness and connections before checking the sensors or switches
below.
Note
Make the system inspection first. If no problem is found, continue with the next system
inspection of the Troubleshooting Guide. (Refer to pages 4B—7 and 8.)
Possible \ cause
\ Page
Solenoid valve (Pres-sure regula-tor control)
Water thermo
sensor Intake air
thermo sensor
Engine con-trol unit terminal
2K
System inspection
Symptom 4B—56 4B—97 4B—94 4B—89 4B—55
Engine stalls or rough after hot starting 2 3
A
5 1
76G04B-074
System Inspection
1. Connect the SST to the engine. (Refer to page
4B—47.)
2. Start the engine.
76G04B-075
3. Warm up the engine to normal operating temper-
ature and stop the engine.
Warning
Be careful when disconnecting the water ther-
mo sensor connector because the surround-
ing area is very hot.
4. Lift the air cleaner upper cover assembly.
5. Heat the intake air thermo sensor to above 10°C
(50 °F).
76G04B-076
4B—55

AIR INJECTION SYSTEM 4B
TROUBLESHOOTING
Check the condition of the wiring harness and connectors before checking the sensors or switch.
Note
Make the system inspection first. If no problem is found, continue with the next system
inspection of the Troubleshooting Guide. (Refer to pages 4B—7 and 8.)
Possible cause Air control valve Reed valve System inspection
Page 4B—69 4B—70 4B—69
Checking order 2 3 1
76G04B-097
System Inspection
1. Warm up the engine and run it at idle.
2. Lift up the air cleaner upper case.
3. Check that air is sucked into the air passage.
4. Increase the engine speed to 2,500 rpm and
check that no air is sucked into the passage.
Air Control Valve
Inspection
1. Remove the air control valve.
4B-69

4B EGR SYSTEM
TROUBLESHOOTING
Check the condition of the wiring harness and connectors before checking the sensors or switches below.
Note
Make the system inspection first. If no problem is found, continue with the next system
inspection of the Troubleshooting Guide. (Refer to pages 4B—7 and 8.)
Possible cause
Solenoid
valve (EGR)
EGR modula-tor valve
EGR con-trol valve
Water
thermo sensor
Water
thermo switch
Engine control unit
terminal
System in-spection
2N
Page 4B—72 4B—73 4B—73 4B—97 4B—97 4B—90 4B—72
Checking order 3 2 4 6 5 7 1
76G04B-103
86U04A-130
System Inspection
1. Start the engine.
2. Accelerate the engine and verify that the di-
aphragm of the EGR control valve does not move
while the engine is still cold.
3. Warm up the engine to normal operating temper-
ature and run it at idle.
Warning
Be careful when checking the EGR control
valve because the surrounding area is very
hot.
4. Accelerate the engine and check that the di-
aphragm of the EGR control valve moves upward.
Solenoid Valve (EGR)
1. Disconnect the vacuum hose from the solenoid
valve and vacuum pipe.
2. Blow through the solenoid valve from vacuum hose
A.
3. Check that air flows from port B.
86U04A-131
4B-72

4B CONTROL SYSTEM
RELATIONSHIP CHART
Input Devices and Output Devices
BRAKE LIGHT SWITCH O X X X X X X X X X
ELECTRICAL LOAD CONTROL UNIT X X X X X X X X O X
P/S PRESSURE SWITCH* X X X X X X X X O X
A/C SWITCH O X X X X O O X X O
IGNITION SWITCH
(STA

POSITION) O O X O X X X X O O
INHIBITOR SWITCH o X X X O X X X X O
NEUTRAL
AND
CLUTCH SWITCH o X X X X X X X X O
OXYGEN SENSOR o X X X X X X X X X
WATER THERMO SWITCH (RADIATOR) o X X X O X X X X X
ATMOSPHERIC PRESSURE SENSOR o X X X X O X O O X
INTAKE
AIR
THERMO SENSOR o X X O X X X O O X
WATER THERMO SENSOR o X X O O O X X o X
IDLE SWITCH o o X O X X X X o X
THROTTLE SENSOR o O X X O X X X X O
AIR FLOW METER o X X X X O X X X X
IGNITION COIL o O X O O O X X o O

INPUT
DEVICES
OUTPUT
DEVICES
FUEL
INJECTION
AMOUNT FUEL
INJECTION

TIMING
PRESSURE
REGULATOR
EGR
PURGE
IDLE-UP
(A)*
IDLE-UP
(B)

IDLE-UP

(C)

rr

INPUT
DEVICES
OUTPUT
DEVICES
INJECTOR
AIR

VALVE
SOLENOID
VALVE
AIR

BYPASS
SOLENOID
VALVE
AIR

CONDITIONEI

76G04B-108
4B-84