1987 MAZDA 626 air condition

TUNE-UP PROCEDURE 1 B
76G01A-102
TUNE-UP PROCEDURE
Tune the engine according to the procedures
described below.
Battery
1. Check for corrosion on the terminals, or loose ca-
ble connections.
If necessary, clean the clamps and tighten firmly.
2. Check that the electrolyte level is between the UP-
PER and LOWER marks.
Add distilled water if necessary.
3. Check the specific gravity by using a hydrometer.
If the specific gravity reading is 1.200 or less,
recharge the battery. (Refer to Section 5.)
76G01A-103
Air Cleaner Element
Visually check the air cleaner element for excessive
dirt, damage, or oil. Clean or replace if necessary.
Caution
When cleaning the air cleaner element, blow
dust off from the inside completely first, then
blow from the outside.
76G01B-005
Engine Oil
Check the engine oil level and condition with the oil
level gauge.
Add oil, or change it, if necessary.
4BG01A-010
1B—5

INSTALLATION 1B
76G01A-100
Air Cleaner Assembly
1. Install the air cleaner assembly.
Tightening torque:
16—27
N
m (1.6—2.8 m-kg, 12—20 ft-lb)
2. Connect the air flow sensor connector and air in-
take pipe.
Engine Oil
Add the specified amount and type of engine oil. (Re-
fer to Section 2A.)
Coolant
Close the drain plug, fill the radiator and reservoir tank
with the specified amount and type of coolant. (Re-
fer to Section 3A.)
Check Engine Condition
1. Check for leaks.
2. Perform engine adjustments if necessary.
3. Perform a road test.
4. Recheck the oil and coolant levels.
86U01X-204
1B-81

TUNE-UP PROCEDURE 1C
4BG01 B-006
4BG01B-007
76G01C-237
TUNE-UP PROCEDURE
Turn the engine according to the procedures
described below.
Battery
1. Check for corrosion on the terminals, or loose ca-
ble connections.
If necessary, clean the clamps and tighten firmly.
2. Check the electrolyte level.
If the level is too low, add distilled water to the "UP-
PER LEVEL" mark.
3. Check the specific gravity by using a hydrometer.
If the specific gravity reading is 1.200 or less,
recharge the battery, by referring to Section 5.
Air Cleaner Element
Visually check the air cleaner element for being ex-
cessively dirty, damaged or oil.
Clean or replace it if necessary.
Caution
(Wet type)
Do not clean the air cleaner element with com-
pressed air, replace if necessary.
(Dry type)
When cleaning the air cleaner element, blow
dust off from the inside first, then blow off the
outside.
Engine Oil
Check the engine oil level and condition with the oil
level gauge.
Add oil, or change it, if necessary.
4BG01B-009
1C—5

INSPECTION, ENGINE OIL 2A
86U02X-004
INSPECTION
ENGINE OIL
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temper-
ature and stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil lev-
el and condition.
5. Add or replace oil if necessary.
Note
The distance between the L and F marks on
the level gauge represents 1.0 liter (1.06 US
qt, 0.88 Imp qt).
OIL PRESSURE
1. Remove the oil pressure switch.
69G02A-006
76G02A-005
86U02X-006
2. Screw the SST into the pressure switch installa-
tion hole.
3. Warm up the engine to normal operating tem-
perature.
4. Run the engine at 3,000 rpm, and note the gauge
reading.
Oil pressure:
343—441 kPa
(3.5—4.5 kg/cm2, 50—64 psi)...DOHC 2g4 392 kPa
(3.0—4.0 kg/cm2, 43—57 psi)...SOHC
5. If the pressure is not as specified, check for the
cause, and repair if necessary.
(Refer to Troubleshooting Guide.)
ENGINE OIL
REPLACEMENT
1. Warm up the engine to the normal operating tem-
perature and stop it.
2. Remove the oil filler cap and the oil pan drain plug.
3. Drain the oil into a suitable container.
Warning
Be careful when draining, the oil is very hot.
2A-5

INSPECTION 2B
A
76G02B-006
INSPECTION
ENGINE OIL
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temper-
ature and stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil lev-
el and condition.
5. Add or replace oil if necessary.
Note
The distance between the L and F marks on
the level gauge represents 1.2 liters (1.26 US
qt, 1.05 Imp qt).
OIL PRESSURE
1. Disconnect the oil hose (vacuum pump—cylinder
block).
76G02B-007
2. Set the SST as shown.
3. Remove the vacuum pump drive belt to prevent
heat damage to bearing.
4. Warm up the engine to normal operating tem-
perature.
76G02B-008
5. Run the engine first at 1,000 rpm, then at 3,000
rpm and note the gauge reading.
Standard oil pressure kPa (kg/cm2, psi)

1,000 rpm 147-245 (1.5-2.5, 21-36)
3,000
rpm
343—441 (3.5-4.5, 50—64)

6. If the pressure is not as specified, check for the
cause, and repair if necessary.
(Refer to Troubleshooting Guide.)
76G02B-009
2B—5

TROUBLESHOOTING GUIDE
4A

TROUBLESHOOTING GUIDE
F6 (GENERAL)
The Troubleshooting Guide lists the systems most likely to cause
a
given symptom. After finding the
system(s)
to
check, refer
to
the pages shown
for
detailed guides
for
each system.
\\ POSSIBLE CAUSE
\ PAGE


SYMPTOM
Air

cleaner
(Air
cleaner
element)
intake
air
temperature
control

system
Idle

adjustment
Fuel
system
(Carburetor,
Fuel
pump)

idle-up

control
system
Exhaust
system
Positive
crankcase
ventilation

system
Auto-return
choke
system

\\ POSSIBLE CAUSE
\ PAGE


SYMPTOM 4A—23 4A—60 4A—38 4A—24 4A—68 4A—96 4A—67 4A—40
1 Hard start
or
won't start (Cranks
OK)
1 2

2 Engine stalls During warm
up
3 2 1 4
2 Engine stalls After warm
up
4 2 5 1 3

3 Rough Idle During warm
up
3 2 1 4
3 Rough Idle After warm
up
3 2 5 1 4

4 High idle speed after warm
up
1 3 2

5 Poor acceleration, hesitation, or lack
of
power
1 2 3

6 Runs rough
on
deceleration
1

7 Afterburn
in
exhaust system
1

8 Poor fuel consumption
2 1 4 3

9 Fails emission test
2 1 4 5 3

76G04A-015
The numbers of the list show the priorities
of
inspections from the most possible to that with the lowest
possibility.
These were determined
on
the following basis:
• Ease
of
inspection
•
Most possible system
•
Most Possible point
in
system
TROUBLESHOOTING PROCEDURE:
1st Check the following items:
Electrical system
1) Battery condition
2) Fuses
Ignition system
1) Spark plugs
2) Ignition timing
Fuel system
1) Fuel level
2) Fuel leakage
3) Fuel filter
4) Idle speed
Intake
air
system
1) Vacuum
or air
leakage
2) Vacuum hose routing
3) Accelerator cable
4) Choke cable
2nd Check Fuel and Emission Control Systems
Engine
1) Compression
2) Overheating
Others
1) Clutch slippage
2) Brake dragging
4 A-17

4A TROUBLESHOOTING GUIDE
F6 (SINGAPORE)
The Troubleshooting Guide lists the systems most likely
to
cause
a
given symptom. After finding
the

system(s)
to
check, refer
to the
pages shown
for
detailed guides
for
each system.
POSSIBLE CAUSE
\ PAGE


SYMPTOM
Air

cleaner
(Air
cleaner
element)

Intake

air
temperature
control
system

Idle

adjustment
Fuel
system
(Carburetor,
Fuel
pump)

Air

injection
system
Deceleration
control
system
Positive
crankcase
ventilation
system

Exhaust

system

Idle-up

control
system

POSSIBLE CAUSE
\ PAGE


SYMPTOM 4A-23 4A-60 4 A—38 4A—24 4A-58 4A-45 4A-67 4A-SW 4A—68
1 Hard start
or
won't start (Cranks
OK)
1 2

2 Engine stalls During warm
up
3 2 1 4
2 Engine stalls After warm
up
3 2 4 1

3 Rough idle During warm
up
3 2 1 4
3 Rough idle After warm
up
3 2 4 1

4 High idle speed after warm
up
1 4 3* 2

5 Poor acceleration, hesitation,
or
lack
of
power
1 2 3

6 Runs rouah
on
deceleration
2 1

7 Afterburn
in
exhaust svstem
2 1

8 Poor fuel consumption
2 1 4 3

9 Fails emission test
6 4 5 3 2 1
Only MTX
76G04A-016
The numbers
of
the list show the priorities
of
inspections from the most possible to that with the lowest
possibility.
These were determined
on the
following basis:
• Ease
of
inspection
•
Most possible system
•
Most possible point
in
system
TROUBLESHOOTING PROCEDURE:
1st Check
the
following items:
Electrical system
1) Battery condition
2) Fuses
Ignition system
1) Spark plugs
2) Ignition timing
Fuel system
1) Fuel level
2) Fuel leakage
3) Fuel filter
4) Idle speed
Intake
air
system
1) Vacuum
or air
leakage
2) Vacuum hose routing
3) Accelerator cable
Engine
1) Compression
2) Overheating
Others
1) Clutch slippage
2) Brake dragging
2nd Check
the
Fuel
and
Emission Control Systems
4A—18

TROUBLESHOOTING GUIDE
4A

FE
12
VALVE and
F8
(EXCEPT MIDDLE EAST and GENERAL)
The Troubleshooting Guide lists the systems most likely to cause
a
given symptom. After finding
the

system(s)
to
check, refer
to
the pages shown
for
detailed guides
for
each system.
POSSIBLE CAUSE
\ PAGE
SYMPTOM


Air

cleaner
(Air

cleaner

element)

Intake

air

temperature

control
system

Idle

adjustment
Fuel
system
(Carburetor,
Fuel
pump)
PTC
heater
system

Air

injection
system
Positive
crankcase
ventilation
system
Deceleration
control
system

Idle-up

control
system

Ignition

control
system

POSSIBLE CAUSE
\ PAGE
SYMPTOM

4A-23 4A-60 4A-38 4A-24 4A-42 4A-58 4A-67 4A—45 4A—68 4 A—80
1 Hard start
or
won't start
(Cranks
OK)
1 2

2 Engine stalls During warm
up
5 4 1 6 2 3
2 Engine stalls After warm
up
3 2 4 1

3 Rough idle During warm
up
5 4 1 6 2 3
3 Rough idle After warm
up
3 2 4 1

4 High idle speed after warm
up
1 4 3 2

5 Poor acceleration, hesitation, or lack
of
power
1 4 2 3

6 Runs rough
on
deceleration
2 1

7 Afterburn
in
exhaust system
2 1

8 Poor fuel consumption
3 1 4 2
4
9 Fails emission test
6 2 5 3 1 4

76G04A-017
The numbers of the list show the priorities
of
inspections from the most possible to that with the lowest
possibility.
These were determined
on the
following basis:
• Ease
of
inspection
•
Most possible system
•
Most possible point
in
system
TROUBLESHOOTING PROCEDURE:
1st Check the following items:
Electrical system
1) Battery condition
2) Fuses
Ignition system
1) Spark plugs
2) Ignition timing
Fuel system
1) Fuel level
2) Fuel leakage
3) Fuel filter
4) Idle speed
Intake
air
system
1) Vacuum
or air
leakage
2) Vacuum hose routing
3) Accelerator cable
Engine
1) Compression
2) Overheating
Others
1) Clutch slippage
2) Brake dragging
2nd Check the Fuel
and
Emission Control Systems
4A—19