1987 MAZDA 626 air condition

4A CONTROL SYSTEM
Terminal (Wire color) Connected to Condition Voltage

C (BL) Rear defroster switch Rear defroster switch
ON
Below 1,5V C (BL) Rear defroster switch
Rear defroster switch OFF Battery voltage
D
(LG) A/C switch A/C operated Below 1,5V D
(LG) A/C switch
A/C not operated Battery voltage
E (LY) Solenoid valve (Main
air
bleed control) Intake manifold vacuum more than 300 mmHg (11.8 inHg), and radiator coolant temperature above 17°C (63 °F)
Battery voltage E (LY) Solenoid valve (Main
air
bleed control)
Others Below 1,5V
F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature below 17°C (63°F) Below 1,5V F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
G (YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
J (BW) Ignition switch Ignition switch
ON
Battery voltage
K (GO) Solenoid valve (Choke opener) Radiator temperature below 17°C (63°F)
or
during cranking and
27
sec. after engine starts Below 1,5V K (GO) Solenoid valve (Choke opener)
Others Battery voltage
L (LsB) Idle switch Idling Battery voltage L (LsB) Idle switch
Accelerator pedal depressed Below 1,5V
M
(GL)
Air bypass solenoid valve Idle switch OFF and engine speed above approx. 2,100 rpm Below 1,5V M
(GL)
Air bypass solenoid valve
Others Battery voltage
0
(BY)
Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 0
(BY)
Ignition switch
(START position) Cranking Battery voltage
P
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx.
2,300
rpm

Below 1,5V P
(LW) Solenoid valve (A/C)
Others Battery voltage
Q (YW) Idle-up solenoid valve Headlight switch ON, rear defroster switch ON,
fan
speed control switch
is
3rd
or
4th position, A/C oper-ated,
or
engine coolant temperature below 72°C (162°F)
Below 1,5V Q (YW) Idle-up solenoid valve
Others Battery voltage
R
(LB)
Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1,5V R
(LB)
Fan speed control switch
Fan speed control switch OFF Battery voltage

76G04A-171

f ° O M K I G E C
R P N L J H F D B

4A-88

CONTROL SYSTEM 4 A
FE and F8 Engine — ATX (General)
Terminal (Wire color) Connected to Condition Voltage

1A
(BW)
Ignition switch Ignition switch
ON
Battery voltage
1B (GR) Solenoid valve (Main
air
bleed control) Others Battery voltage 1B (GR) Solenoid valve (Main
air
bleed control) Radiator coolant temperature below 17°C (63°F)
or
intake manifold vacuum more than 200 mmHg (7.9 inHg)
Below 1,5V
1C
— — —

1D
— — —

1E
— — —

1F
— --

1G
-—

1H
(LW) Solenoid valve (A/C) A/C operated Below 1,5V 1H
(LW) Solenoid valve (A/C)
Others Battery voltage
11
(LW) Idle-up solenoid valve Inhibitor switch OFF and, headlight switch ON, rear defroster switch ON, fan speed control switch
is 3rd
or 4th position, A/C operated,
or
engine coolant tem-perature below 72°C (162°F)
Below 1,5V 11
(LW) Idle-up solenoid valve
Others Battery voltage
1J
(B)
Ground
—
Below 1.5V
2A (YL) Ignition coil Ignition switch
ON or
engine running Battery voltage
2B (LB) Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1.5V 2B (LB) Fan speed control switch
Fan speed control switch OFF Battery voltage
2C
(BL)
Rear defroster switch Rear defroster switch
ON
Below 1,5V 2C
(BL)
Rear defroster switch
Rear defroster switch OFF Battery voltage
2D
(LG) A/C switch A/C operated Below 1,5V 2D
(LG) A/C switch
A/C not operated Battery voltage
2E
(RG)
Headlight switch Headlight switch
ON
Below 1,5V 2E
(RG)
Headlight switch
Headlight switch OFF Battery voltage
2F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1.5V 2F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
2G
— — —

2H
(L)
Water thermo switch
(Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V 2H
(L)
Water thermo switch
(Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
21 (LB)
Vacuum switch Vacuum less than 200 mmHg (7.9 inHg) Below 1.5V 21 (LB)
Vacuum switch
Vacuum more than 200 mmHg (7.9 inHg) Battery voltage
2J
(RL)
OD release solenoid Engine coolant temperature below 72°C (162°F) Below 1,5V 2J
(RL)
OD release solenoid
Engine coolant temperature above 72°C (162°F) Battery voltage

4A-89

4A CONTROL SYSTEM
Terminal
(Wire color) Connected to Condition Voltage

2K
— — —

2L
(BR) Inhibitor switch "P"
or "N"
range Below 1,5V 2L
(BR) Inhibitor switch
Others Battery voltage
2M
(BY)
Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 2M
(BY)
Ignition switch
(START position) Cranking Battery voltage
2N
— — —
76G04A-172
(2M X
2
X
2F 2C

X 2L
2J 2H 2F 2D 2B

fll X >< X

1J 1H
>< X
1B

FE and F8 Engine — MTX (General)
Terminal (Wire color) Connected to Condition Voltage

A
(W)
Headlight switch Headlight switch
ON
Below 1,5V A
(W)
Headlight switch
Headlight switch OFF Battery voltage
B
(B)
Ground
—
Below 1,5V
C
(BL) Rear defroster switch Rear defroster switch
ON
Below 1,5V C
(BL) Rear defroster switch
Rear defroster switch OFF Battery voltage
D
(LG) A/C switch A/C operated Below 1.5V D
(LG) A/C switch
A/C not operated Battery voltage
E
(LB) Solenoid valve (Main
air

bleed control)
Intake manifold vacuum more than 300 mmHg (11.8 inHg), and radiator coolant temperature above 17°C (63 °F)
Battery voltage E
(LB) Solenoid valve (Main
air

bleed control)
Others Below 1.5V
F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1,5V F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
G (YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
I
— — —

J
(BW)
Ignition switch Ignition switch
ON
Battery voltage
K
— —

L
— — —

M
— — —

N
— —
4A-90

CONTROL SYSTEM 4 A
Terminal (Wire color) Connected to Condition Voltage

0 (BY)
Ignition switch*
(START position) Ignition switch
ON
Below 1.5V 0 (BY)
Ignition switch*
(START position) Cranking Battery voltage
P
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx.
2,300
rpm
Below 1,5V
Others Battery voltage
Q (YW) Idle-up solenoid valve Headlight switch ON, rear defroster switch ON,
fan
speed control switch
is
3rd
or
4th position, A/C oper-ated,
or
engine coolant temperature below 72°C (162°F)
Below 1,5V
Others Battery voltage
R
(LB)
Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1,5V R
(LB) Fan speed control switch OFF Battery voltage
*
Not
used
76G04A-173

{
Q
0
><
K
X
G E C A
^

R P
R X
J H F D B

FE 8Valve — Unleaded Fuel
Terminal (Wire color) Connected to Condition Voltage

A
(L)
Coast enrichment solenoid valve Engine speed approx. 1,500—2,300 rpm and idle switch
ON

Below 1,5V A
(L)
Coast enrichment solenoid valve
Others Battery voltage
B
(B)
Ground
—
Below 1,5V
C (LB)
Air bypass solenoid valve Engine speed above approx. 3,500 rpm and idle
switch
ON

Below 1,5V C (LB)
Air bypass solenoid valve
Others Battery voltage
D
(YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
E
— — —

F
(BW)
Ignition switch Ignition switch
ON
Battery voltage
G (YW) Slow fuel cut solenoid valve Engine speed above approx. 2,300 rpm and idle
switch
ON

Battery voltage G (YW) Slow fuel cut solenoid valve
Others Below 1.5V
H
(LW) A/C switch A/C operated and engine speed above approx.
1,500 rpm
Battery voltage H
(LW) A/C switch
A/C not operated
or
engine speed below approx.
1,500 rpm
Below 1,5V

4A—91

TROUBLESHOOTING GUIDE 4B
TROUBLESHOOTING GUIDE
This troubleshooting guide shows the malfunction numbers and the symptoms of various failures.
Perform troubleshooting as described below.
Possible cause
Symptom
Input sensors and switches
o> Q.
C
0
Jh c 01
4B-14
a> 4)
E
o
4B-1S
o in c « m o E k_ 0) c.
0 <0 £
4B-16
o CO c a> 0) o E
a>
.x
co
4B-17
o 10 c a) co
4B-18
o in c a> (0
o> o> a>
a) £ a VI o E
4B-19
0 <0 c a> 0) c a> 01
S? o
4B-20
E a> in (0
o 10 A •o 0) 0> u.
4B-21
Output solenoid valves
o «
3 O) 0)
0) 0) 01
0> > 10 >
•o o c V o tt)
4B-22
0)
OI

0> > CO >

TJ
O c 0> o CO
4B-23
oc O u
o> > 75 >
•o o c a> o 05
4B-23
0 a. 3 1
2
0) > (0 >
"D O
o 0> in in a a >. £
4B-23
ffl a 3 • a>
2
a> > 10 >
"O o c a> o
CO Q. >. JO
4B-24
Fault Indicated by SST
Code No. 01 08 09 10 12 14 15 17 25 26 28 34 35
Hard start or won't start
(Cranks OK)
Engine stalls
Rough
idle
While warming up
After warming up
While warming up
After warming up
High idle speed after
warming up
TROUBLESHOOTING PROCEDURE
Note
Step 1 under symptom is to quickly determine what system or unit may be at fault by use of the SST. (Self-Diagnosis Checker 49 H018 9A1)
1st:
Check input sensors and output solenoid valves with the
SST.
(Refer
to
page 4B—10.)

2nd:
Check other switches with the
SST.
(Refer
to
page 4B—26.)

3rd:
Check the following items:

11
Poor acceleration, hesita-
tion or lack of power
Runs rough on deceleration
Afterburn in exhaust system
Poor fuel consumption
Engine stalls or rough after hot starting
Electrical system
1) Battery condition
2) Fuses

Fuel system
1) Fuel level 2) Fuel leakage
3) Fuel filter 4) Idle speed

Engine
1) Compression 2) Overheating

Ignition system

1) Ignition spark 2) Ignition timing

Intake air system
1)
Air
cleaner element 2) Vacuum
or air
leakage 3) Vacuum hose routing
4) Accelerator cable

Others
1) Clutch slippage 2) Brake dragging

Fails emission test 4th:
Check Fuel and Emission Control Systems. (Refer
to
page 4B—8.)

76G04B-003
4B—7

IDLE ADJUSTMENT 4B
76G04B-034
76G04B-035
Idle mixture
Automatic
Control
Function
Engine Control Unit

IDLE
ADJUSTMENT
IDLE SPEED
Preparation
1) Check the condition of the engine (plugs, leaks in
hoses, etc.).
2) Make sure all accessories are OFF.
3) Warm up the engine and run it for three minutes
at 2,500—3,000 rpm in neutral.
4) Check the initial ignition timing and adjust if
necessary.
Inspection and Adjustment
Caution
Disconnect the air bypass solenoid connec-
tor when checking and adjusting the idle
speed.
1. Check that the idle speed is within specification.
Specification:
MTX—800 +58 rpm
ATX—900 +58 rpm (P range)
2. If the idle speed is not within specification, remove
the blind cap from the throttle body and adjust it
by turning the air adjust screw.
IDLE MIXTURE
Because an automatic compensation function
for air/fuel mixture is built into the engine con-
trol unit, it is not necessary to check and adjust
the idle mixture.
86U04A-049
4B-29

4B INTAKE AIR SYSTEM
69G04A-059
86U04A-053
79G04D-084
PARTS INSPECTION
Air Cleaner Element
1. Check the condition of the air cleaner element.
2. Replace, if necessary.
Caution
Do not use the compressed air to clean the
air cleaner element.
Accelerator Cable
1. Inspect the deflection of the cable. If the deflec-
tion is not within 1—3 mm (0.04—0.12 in.), ad-
just by turning nuts A.
2. Depress the accelerator pedal to the floor and con-
firm that the throttle valve is fully opened. Adjust
by turning bolt B if necessary.
Throttle Body
Caution
a) The throttle adjust screw is preset and
sealed.
Do not attempt to adjust it.
If there is a malfunction of the throttle ad-
just screw, lever, or throttle valve, replace
the throttle body as an assembly.
b) Do not remove the thin sealing coating from
the throttle valve or bore.
79G04D-085
4B-32

INTAKE AIR SYSTEM 4B
76G04B-039
D C B E\\ I I A
p 'V > "
F G
76G04B-040
76G04B-041
1. Check that the throttle valve moves smoothly when
the throttle lever is moved from fully closed to fully
open.
2. Warm up the engine and run at idle.
3. Check the vacuum generated at each port as
shown in the following table.

~ —Condition
Port (Connected to) ——____ Idle Other
A (solenoid valve, EGR) No Yes
B (distributor, advance) No Yes
C (EGR modulator valve) No Yes
D (water thermo valve) No Yes
E (vacuum switch valve
&
charcoal canister) Yes
F (distributor, retard
& air
control valve) Yes
G (distributor, advance) Yes

4. If vacuum is not obtained as in the table, clean the
necessary port.
Dynamic Chamber
1. Visually check the dynamic chamber for damage.
2. Replace, if necessary.
Intake Manifold
1. Visually check the intake manifold for damage.
2. Replace, if necessary.
76G04B-042
4B—33