1987 MAZDA 626 oil

7 A ASSEMBLY
86U07A-106
86U07A-107
86U07A-108
8. Install the new breather.
9. Install the new change rod oil seal.
10. Install the change rod ©, the boot the spring

(3),
the reverse gate @, and selector ©, as shown.
11. Install the new roll pin.
12. Install the change arm.
Tightening torque: 12—14 N-m
(120—140 cm-kg, 104—122 in-lb)
13. Install the guide plate.
Tightening torque:
©8—11 N-m
(80—115 cm-kg, 69—100 in-lb)
(1)22—33 N-m
(2.25—3.35 m-kg, 16—25 ft-lb)
14. Install reverse lever, and reverse lever shaft.
15. Install the new roll pin.
16. Install the speedometer driven gear assembly.
86U07A-109
7A-42

INSTALLATION 7A
14. Install the clutch release cylinder.
Tightening torque: 19—26 N-m
(1.9—2.6 m-kg, 14—19 ft-lb)
76G07A-060
15. Install the gusset plates.
Tightening torque: 37—52 N-m
(3.8—5.3 m-kg, 27—38 ft-lb)
76G07A-061
16. Replace the clips at the end of the driveshafts and
joint shaft with new ones.
17. Install the joint shaft and right driveshaft as follows:
(1) Install and tighten the reamer bolts (A); then in-
stall and tighten the standard bolts (§).
Tightening torque:
® :7—10 N-m
(70—100 cm-kg, 43—61 in-lb)
(B) :42—62 Nm
(4.3—6.3 m-kg, 31—46 ft-lb)
76G07A-062
(2) Remove the SST and insert the shaft into the
transaxle.
(3) Pull the front hub outward and connect the
driveshaft to the joint shaft.
(4) Push the joint at the differential side to secure-
ly connect the driveshaft to the joint shaft.
Note
a) After installation, pull the front hub outward
to confirm that the driveshaft doesn't come
out.
b)Do not damage the oil seal.
86U07A-219
7A-55

7A INSTALLATION
76G07A-063
76G07A-064
18. Install the left driveshaft as follows:
(1) Pull the front hub outward and insert the
driveshaft into the transaxle.
(2) Push the joint at the differential side to connect
the driveshaft to the differential side gear.
Note
a) Do not damage the oil seal.
b) After installation, pull the front hub outward
to confirm that the driveshaft doesn't come
out.
19. Install the lower arm ball joints to the knuckles and
tighten the bolts and nuts.
Tightening torque: 43—54 N-m
(4.4—5.5 m-kg, 32—40 ft-lb)
20. Install the under cover, (except DOHC)
Note
Before installation, fill the notches with sili-
con as shown in the figure.
Tightening torque: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
21. Install the stabilizer bar control links as follows.
(1) Install the stabilizer bar control link.
(2) Adjust protrusion to 20.1 mm (0.79 in)
(3) Tighten bolt to specified torque.
Tightening torque: 16—23 N-m
(1.6—2.3 m-kg , 12—17 ft-lb)
76G07A-065
76G07A-066
22. Install the tie-rod ends and new cotter pine.
Tightening torque: 29—44 N-m
(3.0—4.5 m-kg, 22—33 ft-lb)
23. Install the splash shields.
Tightening torque: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
24. Install the front wheels.
Tightening torque: 88—118 N-m
(9.0—12.0 m-kg, 65—87 ft-lb)
—56

INSTALLATION 7A
25. Install the grounds to the transaxle case.
Tightening torque:
8—11 N-m (80—115 cm-kg, 69—100 in-lb)
26. Connect the speedometer cable.
76G07A-067
76G07A-068
76G07A-069
76G07A-070
27. Install the intercooler pipe and hose. (RF-CX)
Tightening torque:
19—26 Nm (1.9—2.6 m-kg, 14—19 ft-lb)
28. Install the brake vacuum pipe. (RF-CX)
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
29. Connect the brake vacuum hose. (RF-CX)
30. Install the air cleaner assembly and connect the
air flow meter connector.
Tightening torque:
16—27 Nm (1.6—2.8 m-kg, 12—20 ft-lb)
31. Connect the distributor lead.
32. Connect the main fuse block.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
33. Install the battery carrier and battery.
34. Add the correct quantity of the specified transaxle
oil.
Specified
Type
A.T.F.: DEXRON II
Above 0°F:
API: GL-4 or GL-5
SAE 80W-90 or SAE 90
Capacity:
3.35 liters (3.6 US qt, 3.0 Imp qt)
7A-57

7B
AUTOMATIC TRANSAXLE
(Electronically Controlled and 4-Speed)
OUTLINE 7B— 2
SPECIFICATIONS 7B— 2
COMPONENT LOCATION 7B— 3
STRUCTURAL VIEW 7B— 5
OPERATION OF COMPONENTS 7B— 6
FLUID PASSAGE LOCATION 7B— 9
TROUBLESHOOTING (G4A-EL) 7B— 12
GENERAL NOTE 7B— 12
STEP 1
(WARNING CODE RETRIEVAL) 7B— 15
STEP 2
(PRELIMINARY INSPECTION) 7B— 22
STEP 3 (SIGNAL INSPECTION) 7B— 24
STEP 4 (STALL TEST) 7B— 27
STEP 5 (TIME LAG TEST) 7B— 30
STEP 6 (OIL PRESSURE TEST) 7B— 31
STEP 7 (ROAD TEST) 7B— 34
TROUBLESHOOTING (G4A-HL) 7B— 41
GENERAL NOTE 7B— 41
STEP 1
(PRELIMINARY INSPECTION) 7B— 44
STEP 2 (ELECTRICAL
SYSTEM INSPECTION) 7B— 47
STEP 3 (STALL TEST) 7B— 49
STEP 4 (TIME LAG TEST) 7B- 52
STEP 5 (ROAD TEST) 7B— 53
STEP 6 (OIL PRESSURE TEST) 7B— 58
ELECTRICAL SYSTEM
COMPONENTS 7B— 63
MODE SWITCH (G4A-EL) 7B— 63
HOLD SWITCH (G4A-EL) 7B— 63
OD OFF SWITCH (G4A-HL) 7B— 64
INHIBITOR SWITCH 7B- 65
WATER TEMPERATURE SWITCH 7B— 66
FLUID TEMPERATURE SWITCH
(G4A-EL) 7B— 66
BRAKE LIGHT SWITCH
(G4A-EL) 7B— 66
KICK-DOWN SWITCH (G4A-HL) 7B— 67
PULSE GENERATOR (G4A-EL) 7B- 68
VEHICLE SPEED SENSOR
(G4A-EL) 7B— 68
CRUISE CONTROL SWITCH
(CRUISE CONTROL UNIT) 7B— 68
IDLE SWITCH AND THROTTLE
SENSOR (G4A-EL) 7B— 68
OD RELEASE SOLENOID
VALVE (G4A-HL) 7B— 68
SOLENOID VALVES (G4A-EL) 7B— 69
NO LOAD SIGNAL (G4A-EL) 7B— 69
MODE, AND HOLD INDICATOR
LIGHT (G4A-EL) 7B— 69
OD OFF INDICATOR LIGHT
(G4A-HL) 7B— 69
EC-AT CONTROL UNIT
(G4A-EL) 7B— 69
ON-VEHICLE MAINTENANCE 7B— 71
AUTOMATIC TRANSAXLE
FLUID (ATF) 7B— 71
SELECTOR LEVER 7B— 72
THROTTLE CABLE 7B— 73
CONTROL VALVE BODY 7B— 77
OIL STRAINER 7B— 79
ADJUSTMENT OF 2-4 BRAKE
BAND 78— 80
REPLACEMENT OF
DRIVESHAFT OIL SEAL 7B— 80
OIL COOLER 7B— 81
GOVERNOR (G4A-HL) 7B— 82
REMOVAL 7B— 83
PRECAUTION 7B— 83
DISASSEMBLY 7B— 88
DISASSEMBLY-STEP 1 7B— 88
DISASSEMBLY-STEP 2 7B— 94
DISASSEMBLY-STEP 3 7B— 99
DISASSEMBLY-STEP 4 7B—103
INSPECTION AND REPAIR 7B—107
PRECAUTION 7B—107
TORQUE CONVERTER 7B—107
OIL PUMP 7B—108
CLUTCH ASSEMBLY 7B—113
SMALL SUN GEAR AND
ONE-WAY CLUTCH 7B—122
ONE-WAY CLUTCH AND
CARRIER HUB ASSEMBLY 7B-126
3-4 CLUTCH 7B—128
2-3 ACCUMULATOR 7B—132
GOVERNOR ASSEMBLY
(G4A-HL) 7B-133
LOW AND REVERSE BRAKE 7B—134
2-4 BRAKE BAND 7B—135
BAND SERVO 7B—135
OTHER INSPECTION 7B—135
CONTROL VALVE BODY
(G4A-EL) 7B-136
CONTROL VALVE BODY
(G4A-HL) 7B-155
DIFFERENTIAL 7B—177
OUTPUT GEAR 7B—181
IDLE GEAR 7B—182
BEARING COVER ASSEMBLY 7B—185
BEARING HOUSING 7B—186
ASSEMBLY 7B-187
PRECATION 7B—187
ASSEMBLY-STEP 1 7B—187
ASSEMBLY-STEP 2 7B—197
ASSEMBLY-STEP 3 7B—202
ASSEMBLY-STEP 4 7B—208
INSTALLATION 7B—215
TORQUE SPECIFICATIONS 7B—215
HYDRAULIC CIRCUIT (G4A-EL) 7B—221
HYDRAULIC CIRCUIT (G4A-HL) 7B—239
76G07B-001

OUTLINE 7B
STRUCTUAL VIEW
76G07B-005
1. Coasting clutch 7. Low and reverse brake
2. Forward clutch 8. Output gear
3. Reverse clutch 9. Idle gear
4. Reverse and forward drum 10. Differential
5. 3-4 clutch 11. Parking pawl
6. 2-4 brake band 12. Throttle cable
13. Control body
14. Oil pump
15. Inhibitor switch
16. Pulse generator
17. Fluid temperature switch
7B—5

7B OUTLINE
Transaxle Case
To governor valve
/and 2-3 accumulator
Inlet to control valve body
(governor pressure)
Outlet to torque converter
(Release side)
Outlet to torque converter
(Apply side)
Outlet to 3-4 clutch
To governor valve and 2-3 accumulator^
From governor valve (governor pressure)
To torque converter (Release side)
To torque converter (Apply side)
To 3-4 clutch
From oil pump
(To control valve body)
°Lto coasting clutch
y
To reverse clutch
To forward clutch
To low and reverse brake
To 2-4 brake apply side
CgEfey a —* To 2-4 brake release side
7B—10
76G07B-009

OUTLINE 7B
Transaxle Case
Inlet to control valve body
Outlet coasting clutch
Outlet to reverse clutch
Outlet to forward clutch
Oil Pump
Outlet to oil pump
Outlet for lubrication
Outlet to forward clutch
Inlet to oil pump^
Outlet to reverse clutch
Outlet to coasting clutch
Outlet to control valve body
Inlet for lubrication
Inlet to forward clutch Inlet to coasting clutch
Inlet to reverse clutch
76G07B-010
76G07B-011
7B—11