1987 MAZDA 626 belt

0 PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
EXTERIOR
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Glass, exterior bright metal and paint for damage
• Wheel lug nuts
88—118 N m (9—12 m-kg, 65—87 ft-lb)
• Tire pressures (Refer to section 12)
• All weatherstrips for damage or detachment
• Operation of bonnet release and lock
• Operation of fuel lid and trunk lid (Back door) opener
• Door operation and alignment
• Headlight aiming
INSTALL following parts:
• Wheel caps or rings (if equipped)
• Outside rear view mirror(s)
UNDER BONNET—ENGINE OFF
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
• Engine oil level
• Power steering fluid level (if equipped)
• Brake and clutch master cylinder fluid level (if equipped)
• Windshield washer reservoir fluid level
• Radiator coolant level and specific gravity
Protection °C (°F) Specific gravity at 20°C (68°F)
-4 (25) 1.028
-16(3) 1.054
-26 (-15) 1.066 -40 (-40) 1.078
• Tightness of water hose clamps (including heater hoses)
• Tightness of battery terminals
• Manual transaxle oil level
• Drive belt tensions (Refer to section 1)
• Accelerator cable and its linkage for free movement
• Headlight cleaner fluid level (if equipped)
CLEAN spark plugs
INTERIOR
INSTALL the following parts:
• Rubber stopper for inside rear view mirror
• Fuse for accessories
CHECK the operations of the following items:
• Seat controls (sliding and reclining) and head rest
• Door locks including childproof door locks (if equipped)
• Seat belts and warning system
• Ignition switch and steering lock
• Inhibitor switch (ATX only)
• All lights including warning and indicator lights
• Sound warning system
• Headlight cleaner (if equipped)
• Horn, wipers and washers (front and rear, if equipped)
• Radio and antenna (if equipped)
• Cigarette lighter and clock
• Remote control outside rear view mirrors (if equipped)
• Power windows (if equipped)
• Heater, defroster and air conditioner at various mode
selection (if equipped)
• Sunroof (if equipped)
ADJUST antenna trimmer on radio (if equipped)
CHECK the following items:
• Presence of spare fuse
• Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
• Operation and fit of windows
• Pedal height and free play of brake and clutch pedal
Pedal height mm (in) free play mm (in)
Clutch pedal 216.5-221.5 (8.52-8.72) 5-13 (0.2-0.51)
Brake pedal 222-227 (8.74-8.94) 4-7 (0.16-0.28)
• Parking brake
5-7 noches/98 N (10 kg, 22lb)
UNDER BONNET—ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
• Operation of idle-up system for air conditioner or power
steering (if equipped)
• Automatic transaxle fluid level
• Operation of dash pot
• Initial ignition timing
• Idle speed
ON HOIST
CHECK the following items:
• Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
• Tires for cuts or bruises
• Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
REMOVE protective cover from brake discs
ROAD TEST"
CHECK the following items:
• Brake operation
• Clutch operation
• Steering control
• Operation of meters and gauge
• Squeaks, rattles or unusual noise
• Engine general performance (including turbo)
• Emergency locking retractors
• Cruise control system (if equipped)
AFTER ROAD TEST
REMOVE seat and floor mat protective covers
CHECK for necessary owner information materials, tools and
spare tire in vehicle
-76G00X-002
0-2

For ECE Leaded gasoline
Chart symbols:
I
A
R
T
O
X
Inspect: Visual examination or functional measurement of a system's operation (performance)
Adjust : Examination resulting in adjustment or replacement
Replace or change
Tighten
Applicable
Not applicable
F8 engine with carbretor, MTX, ATX
FE engine with carbretor, MTX, ATX
FE DOHC engine with fuel injection, 4WS, MTX
RF-CX, RF-N engine with MTX
REMARKS:
Major service interval at 12 months/20,000 km (12,000 Miles), Lubrication service based on distance only 10,000 km (6,000 Miles) not time
After 80,000 km (48,000 Miles) or 48 months, continue to follow the described maintenance items and intervals periodically.
As for * marked items in this maintenance chart, please pay attention to the following points.
*1 Replacement of the timing belt is required at every 100,000 km (60,000 Miles). Failure to repace the timing belt may result in damage to the engine.
*2 If the vehicle is operatie under the following conditions, it is suggested that the engine oil and oil filter be changed more often than at usual recommended intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for a prolonged period in cold temperatures or driving only short distances regulary.
*3. If the vehicle is operated in very dusty or sandy areas, inspect and, if necessary, replace more often than at usual recommended intervals.
*4. This is a full function check of all electrical systems, i.e., all lights, washers (including condition of blades) electrical windows, sunroof, horn, etc....
*5. Replace every two years.
If there has been continuous hard driving, mountain driving, or if the brakes are used extensively or the vehicle is operated in extremely humid climates, the
brake fluid should be changed annually.
>
Z H m >
o m
H >
CD r-m
o m
m O m
(D o> Q. ® a
(Q 0) <0 o
o X m o
m a
o m
c/> o x m a
Emission Control and Related Systems
The ignition and fuel systems are vitally important to the proper operation of the emissions control and related systems, as well as for efficient engine operation.
It is strongly recommended that all servicing related to these systems be done by your Authorized Mazda Dealer.
m a
m z >
z o m
G)

U1
Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x 1000 Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x
1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Battery electrolyte level and specific gravity A A A A O o O O • Electroyte level • Specific gravity 5-8
Drive belts A A A A A O 0 o O • Cracks or damage • Tension

1
A—7
1B—6
1C-7
Engine timing belts Replace every 100,000 Km o o o o — 1A—14 1B—11 1C—11
Engine valve clearance A A A A A o X X o
• Valve clearance: F8 (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE-12-valve, FE (DOHC) IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
1A-10
1C—85
Intake and exhaust manifold nuts and
bolts T T T o o X X
• Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X IN EX
1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X F8, FE 19-30 (1.9-3.1,
14-22)
22-28 (22—2.9, 16-21)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X
RF-CX RF-N 16-23 (1.6-2,3,
12-17)
22-26 (2.2-2.7,
16-20)

1
A—86 1B—68 1C—89
Engine oil *2 R R R R R R R R R o o 0 o
• Oil pan capacity F8, FE: 3.6 liters (3.8 US qt, 3.2 Imp qt) RF-CX, RF-N:
5.0 liters (5.3 US qt, 4.4 Imp qt)
2A—6
2B-6
Oil filter *2 R R R R R R R R o o o o
• Oil filter capacity F8, FE 12-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A—6
2B-6
Fuel filter (R) for carbretor model (R) R (R) R o 0 o o — 4A—37

0 1 00 Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x 1000 Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x 1000
0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Brake lines, Hoses, and connections I I I I O O O O • Proper attachment and connections 11-8
Body condition Inspect annually O O o O -—
Tyres (including spare tyre) Infration pressure adjustment I I I I o O o o • Check the air pressure 12-2
Hinges and cathes A A A A o O o o — —
Underside of vehicle I I I I 0 0 o o — —
Seat belt I I I I o o o o • Opration and looseness 14-101
Road test I I I I o o o o — —
o o o X o o 00

r
For ECE Unleaded gasoline
Chart symbols:
I
A
R
T
O
X
Inspect: Visual examination or functional measurement of a system's operation (performance)
Adjust: Examination resulting in adjustment or replacement
Replace or change
Tighten
Applicable
Not applicable
FE engine with fuel injection, MTX, ATX
FE DOHC engine with fuel injection, 4WS, MTX
FE engine with carburetor, MTX, ATX
RF-CX, RF-N engine with MTX
REMARKS:
Major service interval at 12 months/20,000 km (12,000 Miles), Lubrication service based on distance only 10,000 km (6,000 Miles) not time
After 80,000 km (48,000 Miles) or 48 months, continue to follow the described maintenance items and intervals periodically.
As for * marked items in this maintenance chart, please pay attention to the following points.
*1 Replacement of the timing belt is required at every 100,000 km (60,000 Miles). Failure to repace the timing belt may result in damage to the engine.
*2 If the vehicle is operated under the following conditions, it is suggested that the engine oil and oil filter be changed more often than at usual recommended
intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for a prolonged period in cold temperatures or driving only short distances regulary.
*3. If the vehicle is operated in very dusty or sandy areas, inspect and, if necessary, replace more often than at usual recommended intervals.
*4. This is a full function check of all electrical systems, i.e., all lights, washers (including condition of blades) electrical windows, sunroof, horn, etc....
*5. Replace every two years.
If there has been continuous hard driving, mountain driving, or if the brakes are used extensively or the vehicle is operated in extremely humid climates, the brake fluid
should be changed annually.
Emission Control and Related Systems
The ignition and fuel systems are vitally important to the proper operation of the emissions control and related systems, as well as for efficient engine operation. It is
strongly recommended that all servicing related to these systems be done by your Authorized Mazda Dealer.
>
Z H m z >
o m
H >
DJ r~ m
m o m
c 3 5"
(/> O X m o c i-m
o
m z >
z o m
CD

Interval
Procedure & item
Number of Months or km, whichever corns first
Months

x
1000
Km
Miles x 1000
0.6
6
10
12
20
12
18
30
18
24
40
24
30
50
30
36
60
36
42
70
42
48
80
48
®3 ©4 Service data and inspection point Page
m z >
z o m
H >
00 I-m
m o m
c 3 a to Qt (0 O
A
Battery electrolyte level and specific gravity O o o o Electroyte level Specific gravity 5-8
Drive belts O O o o Cracks or damage Tension

1
A—7
1B-6
1C-7
Engine timing belts Replace Severy 100,000 Km O O o o
Engine valve clearance
Intake and exhaust manifold nuts and bolts
O
O
o o
Valve clearance: FE-8-valve (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE (DOHC)
IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
O IN EX
FE FE DOHC 19-30(1.9-3.1,
14-22)
22-28 (2.2-2.9
16-21)
1A—14 1B—11 1C-11

1
A—10
1C-85
Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)
1A—86
1B—68 CO 0 1 m o
m a
H m
o m
Engine oil O
Oil filter O
O o o
Oil pan capacity FE: 3.6 liters
(3.8 US qt, 3.17 Imp qt) RF-CX, RF-N: 5.0 liters (5.3 US qt, 4.4 Imp qt)
O o o
Oil filter capacity FE 8-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A-6
2B-6
2A-6
2B-6

o Interval Number of Months or km, whichever corns first
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page x 1000
Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Procedure & item Miles
x
1000 0.6 6 12 18 24 30 36 42 48
Exhaust system heat shields (unlead) I I O O O O • Clearance to body, and exhaust
system 4A-97
Body condition visual only Inspect annually o o O O • Inspect annually —
Tyres (including spare tyre) Infration
pressure adjustment I I I I o o o O • Check the air pressure 12-2
Hinges and cathes A A A A o o o O — —
Underside of vehicle I I I I o o o o — —
Seat belt I I I I o o o o • Opration and looseness 14—101
Road test I I I I o o o o — —
•>1 o o o x o -tx

For General
Chart symbols:
I : Inspect: Visual examination and/or functional measurement of a system's operation or performance.
A : Adjust: Examination resuiting in adjustment or replacement.
R : Replace or change
T : Tighten
O : Applicable
X : Not applicable
© 1 : F6, F8 engine with carburetor, MTX, ATX
© 2 : FE engine with carbretor, MTX, ATX
©3 : FE DOHC engine with fuel injection, MTX
® 4 : RF-N engine with MTX
NOTE:
As the result of visual examination or functional measurement of a system's operation(performance), correct, clean or replace as required.
REMARKS:
After 80,000 km (48,000 Miles) or 48 months, continue to follow the described maintenance items and intervals periodically.
As for * marked items in this maintenance chart, please pay attention to the following points.
*1. If the vehicle is operated under the following conditions, it is suggested that the engine oil and oil filter be changed more often than at usual recommended
intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for a prolonged period in cold temperatures or driving only short distances regularly.
"2. Replacement of the timing belt is required at every 100,000 km (60,000 Miles). Failure to repace the timing belt may result in damage to the engine.
*3 If the vehicle is operated in very dusty or sandy areas, inspect and, if necessary, replace more often than at usual recommended intervals.
*4 Adjust or inspect alternator and water pump drive belt, and power steering and air conditioner drive belt, vacuum pump belt, super charger belt if equipped.
*5 Replace every two years.
If there has been continuous hard driving, mountain driving, or if the brakes are used extensively or the vehicle is operated in extremely humid climates, the
brake fluid should be changed annually.
*6. Only F6 carbretor for Singapore (MTX Model)
Emission Control and Related Systems
The ignition and fuel systems are vitally important to the proper operation of the emissions control and related systems, as well as for efficient engine operation. It i
strongly recommended that all servicing related to these systems be done by your Authorized Mazda Dealer.
o CJ1