1987 MAZDA 626 coolant

4B CONTROL SYSTEM
A:
56G04B-038
j Water thermo
sensor
86U04A-202
86U04A-203
Inspection of Resistance
1. Disconnect the connector from the sensor.
2. Check resistance between the terminals as shown
in the table.
3. Open the throttle valve fully and check resistances
between terminals.
Terminal Closed Fully open
A « B Approx. 500 Q Approx. 4.5 kQ
B «- C 4-6 kQ
4.If not correct, replace the throttle sensor.
WATER THERMO SENSOR
Inspection
1. Remove the water thermo sensor from the cylin-
der head.
2. Place the sensor in water with a thermometer and
heat the water gradually.
3. Check resistance of the sensor with an ohmmeter.
Coolant Resistance
-20°C ( -4°F) 14.5-17.8 kQ
20°C ( 68°F) 2.2-2.7 kfi
40°C (104°R 1.0—1.3 kfi
60°C (140°F) 500—640 n
80°C (176°F) 280-350 Q
4. If not correct, replace the water thermo sensor.
WATER THERMO SWITCH
Inspection
1. Remove the switch from the radiator.
2. Place the switch in water with a thermometer, and
heat the water gradually.
3. Check for continuity of the switch with an
ohmmeter.
Coolant temp. Continuity
More than approx. 17°C (63°F) Yes
Less than approx. 17°C (63°F) No
76G04B-132 4. If not correct, replace the water thermo switch.
4B—97

4C TROUBLESHOOTING WITH SST
Is there continuity between air flow sensor and
engine control unit?
Air flow sensor Engine control unit
D (RB wire) 2E
E (RW wire) 2B
NO
YES
Is there 12V at terminal B of air flow sensor connector? (Refer to page 4C—103)
YES
Is there continuity between terminal F of air flow sensor and ground? (Refer to page 4C-103)
YES
NO
NO
PC: Open circuit in wiring harness
PC: Open or short circuit in wiring harness from terminal B to control relay
PC: Open circuit in wiring harness
PC: • Engine control unit malfunction • Short circuit in wiring from terminal D of air flow sensor to engine control unit
76G04C-022
Code No. 09 (Water thermo sensor)
Are there poor connections in water thermo sensor circuit?
NO
Is there continuity between water thermo sensor and engine control unit?
YES
Is resistance of the water thermo sensor OK? Resistance:
YES
Water thermo sensor Enaine control unit
A (YB wire) 21
B (LgY wire) 2C
NO
Coolant temp Resistance
-20°C ( —4°F) 14.5-17.8 kfl
20°C ( 68°F) 2.2- 2.7 kfi
40°C {104°F) 1.0- 1.3 kfi
60°C (140°F) 500-640 fi
80°C (176°F) 280-350 fi
NO
YES
Is same Code No. present after performing after-repair procedure? (Refer to page 4C—12)
YES
Are engine control unit 21 and 2C terminal voltages OK? (Refer to page 4C—98)
YES
NO
NO
PC: Possible Cause
Repair or replace connector
PC: Open circuit in wiring harness from water thermo sensor to engine control unit
Replace water thermo sensor
Water thermo sensor and circuit OK
PC: Short circuit in wiring harness
PC: Engine control unit malfunction
76G04C-023
4C—18

INTAKE AIR SYSTEM 4C
76G04C-054
76G04C-055
76G04C-056
Removal Note
Water hose
Before disconnecting the water hose, drain two liters
of engine coolant.
Delivery pipe assembly.
1. Separate the fuel return pipe from the delivery pipe
assembly.
2. Remove the delivery pipe assembly and the fuel
return pipe.
PARTS INSPECTION
Air Cleaner Element
1. Check the condition of the air cleaner element.
2. Blow out the dust with compressed air, if
necessary.
Caution
a) The air cleaner must be replaced at the in-
tervals outlined in the maintenance
schedule.
b) Never drive the vehicle without the air
cleaner element, otherwise, damage to the
air flow sensor (hot wire) will occur.
c) Never use an oil permeated air cleaner ele-
ment, otherwise, contamination of the hot
wire will occur.
4C—33

4C INTAKE AIR SYSTEM
Installation Note
Water hose spring clamps
Face the clamp end as shown in the figure.
Gasket
Use new gaskets at the intake manifold, dynamic
chamber, and throttle body.
86U04A-056
• . v 1
Engine 1 Ml' ' •-
hanger ^ •
• i::£?^Solenoid valve bracket
Air cleaner. r^I. ^jUvW;
Th V
Ground harnesses
Make sure that the ground harnesses are tightened
securely at the following positions.
(1) Air cleaner upper case
(2) Solenoid valve braket
(3) Engine hanger
76G04C-062
Solenoid valve connectors
Connect the solenoid valve connectors at the posi-
tions shown in the figure.
76G04C-063
Inspection after installation
1. After completing installation, fill up the engine with
the specified engine coolant.
2. Warm up the engine and run it at idle.
3. Check for any vacuum, coolant, or fuel leaks.
76G04C-064
4C-38

4C ISC SYSTEM

IDLE
SPEED CONTROL
(ISC)
SYSTEM
Air valve BAC valve (ISC valve + air valve)
ISC valve
Air passage
c=£> Coolant passage
Idle switch
Large
Bypass air
amount
Small
Characteristics of air valve
Low 50°C (122°F) High
Coolant temperature
76G04C-077
To improve idle smoothness, the ISC system controls the intake air amount by regulating the bypass
air amount that passes through the throttle body.
This system consists of the BAC valve and the control system.
The BAC valve consists of the air valve which functions only when the engine is cold (below 50°C
(122°F)) and the ISC valve which works throughout the entire engine speed range.
4C-44

ISC SYSTEM 4C
COMPONENT DESCRIPTION
Component Function Remark
A/C switch Detects air conditioner operation; sends
signal to engine control unit Switch ON when air conditioner
operating
Air valve When cold, supplies bypass air into dy-namic chamber • Engine speed increased to shorten warm-up period • Thermo wax type
• Installed in BAC valve
Clutch switch Detects in-gear condition; sends signal to engine control unit Switch ON when clutch pedal released
E/L control unit Detects that E/L is being applied; sends
signal to engine control unit
Engine control unit Detects signals from input sensors and switches; controls solenoid valve (Idle speed control)
Idle switch Detects when throttle valve fully closed;
sends signal to engine control unit
Installed on throttle body
Ne signal pick-up Detects crank angle at 180° intervals; sends signal to engine control unit Installed in distributor
Neutral switch Detects in-gear condition; sends signal to engine control unit
Switch ON when in gear
P/S pressure switch Detects P/S operation; sends signal to engine control unit Switch ON when steering wheel turned right or left
Solenoid valve (Idle speed control) Controls bypass air amount • Controlled by duty signal from engine control unit • Installed in BAC valve
• Operates idle-up
Test connector For initial idle speed adjustment • Gerrn, 1-pin
• Idle speed feedback control cancelled when connector grounded
Water thermo sensor Detects coolant temperature; sends
signal to engine control unit
76G04C-078
4C—45

4C FUEL SYSTEM
COMPONENT DESCRIPTION
Component Function Remark
Air flow sensor Detects amount of intake air;
sends signal to engine control unit
Clutch switch Detects in-gear condition; sends signal to engine control unit Switch ON when clutch pedal released
Engine control unit Detects signals from input sensors and switches; controls injector and fuel pump operations
Fuel filter Filters fuel
Fuel pump Provides fuel to injectors • Operates while engine running
• Installed in fuel tank
Fuel pump control unit (4WS) Monitors fuel level in left section; controls transfer pump operation
G signal pick-up Detects No.1 cylinder TDC; sends signal to engine control unit Installed in distributor
Idle switch Detects when throttle valve fully closed; sends signal to engine control unit Installed on throttle body
Ignition switch (ST position) Sends engine cranking signal to engine control unit
Injector Injects fuel into intake port • Controlled by signals from engine control unit • High-ohmic injector
Intake air thermo sensor Detects intake air temperature; send signal to engine control unit
Control relay Supplies electric current to injectors fuel pump and engine control unit
Ne signal pick-up Detects crank angle at 180° intervals; sends signal to engine control unit Installed in distributor
Neutral switch Detects in-gear condition; sends signal to engine control unit
Switch ON when in gear
Oxygen sensor (Unleaded fuel) Detects oxygen concentration; sends signal to engine control unit
• Zirconia ceramic and platinum coating • Integrated heater coil
Pressure regulator Adjusts fuel pressure supplied to injectors
Pulsation damper Absorbs fuel pulsation
Throttle sensor Detects throttle valve opening angle;
sends signal to engine control unit
Installed on throttle body
Transfer pump (4WS) Pumps fuel from the left to the right side Controlled by fuel pump control unit
Transfer pump switch (4WS) Detects fuel level in left section;
sends signal to control unit
Water thermo sensor Detects coolant temperature; sends signal to engine control unit
Water thermo switch (Unleaded fuel) Detects radiator coolant temperature; sends signal to engine control unit ON: above 17°C (63°F)
76G04C-088
4C-50

4C PRC SYSTEM
PRESSURE REGULATOR CONTROL
(PRC)
SYSTEM
Distributor (Ne signal)
I Fuel
(To fuel tank)
76G04C-128
To prevent percolation of the fuel during idle after the engine is restarted, vacuum is cut to the pres-
sure regulator, increasing the fuel pressure.
Specified time: Approx. 120 sec.
Operating condition: Coolant temperature — above 70°C (158°F)
Intake air temperature — above 30°C (86°F)....Unleaded fuel
above 50°C (122°F)....Leaded fuel
4C-68