1985 TOYOTA TERCEL torque

o/' \;z\o /
INSPECT BRAKE LINING AND DRUM FOR PROPER
CONTACT
Replace the brake shoe or lathe the brake drum as necess-
4ry.
INSPECT WHEET CYLINDER FOR CORROSION OR
DAMAGE
INSPECT BACKING PLATE FOR WEAR OR DAMAGE
INSTALLATION OF REAR BRAKE
(See page BR-291
1. APPLY LITHIUM SOAP BASE GLYCOL GREASE
TO FOLLOWING PABTS:
(d Two piston cups
(b) Two pistons
2. ASSEMBLE WHEEL CYLINDER
(a) lnstall two new piston cups to each piston, check
that the flanges of the cups are pointed inward.
(b) Install the two pistons and spring into the wheel
cylinder.
(c) Install two new boots.
3. INSTALL WHEEL CYLINDER
Installthe wheelcylinder on the backing plate with the two
bolts.
Torque: 1OO kg-cm (7 ft-lb, 1O N.ml
4. CONNECT BRAKE TUBE TO WHEEL CYLINDER
Using SST, connect the brake tube
ssT 09751 -3601 1
Torque: 155 kg-cm (11 ft-lb, 15 N.ml
4.
5.
Pistoncu'
^cloqO
fl@6alA"
YrlI I Piston
I SPring
Boot

BRAKE SYSTEM - Rear Brake (Wagon 4WD)8R.39
Apply Grease
INSTALLATION OF REAR BRAKE
(See page BR-361
1. APPLY LITHIUM SOAP BASE GLYCOL GREASE
TO FOLLOWING PARTS:
H Two piston cups
(d Two pistons
2. ASSEMBLE WHEEL CYLINDER
(d Install two new piston cups to the pistons.
(d Install the two pistons and spring into the wheel
cylinder. Check that the flanges of the piston are
pointed inward.
(c) Install two new boots.
3. INSTALL WHEEL CYLINDER
Installthe wheelcylinder on the backing plate with the two
bolts.
Torque: lOO kg-cm (7 ft-lb, 1O N.ml
4. CONNECT BRAKE TUBE TO WHEEL CYLINDER
Using SST, connect the brake tube.
ssT 09751 -3601 1
Torque: 155 kg-cm (11 ft-lb, 15 N.ml
5. APPTY HIGH TEMPERATURE GREASE TO
FOLLOWING PARTS:
(a) Backing plate and brake shoe contact points
(b) Anchor plate and brake shoe contact points
(d Strut and adjusting bolt contact points
(d) Strut and brake shoe contact points
Piston cup Piston
'"i'
lKs^*@#@
d@*''*,J."n

BRAKE SYSTEM - Brake Hoses and Tubes
\$-crio
BRAKE HOSES AND TUBES
DISCONNECT AND CONNECT HOSE AND
TUBE
1. DISCONNECT HOSE AND TUBE
(a) Diconnect the clip.
(b) Using a wrench to hold the hose, and SST to hold the
tube, disconnect the tube and hose.
ssT 09751 -3601 1
2. CONNECT HOSE AND TUBE
(a) Connect the hose and tube by hand.
(b) Using a wrench to hold the hose, and SST to hold the
tube, torque the connection.
ssT 09751 -3601 1
Torque: 155 kg-cm (11 ft-lb, 15 N.ml
(c) Install a new hose clip.
INSPECTION OF BRAKE HOSES AND TUBES
1. INSPECT BRAKE HOSES
(a) Inspect the hose for damage, cracks or swelling.
(b) Inspect the threads for damage.
2. INSPECT BRAKE TUBES
(d Inspect the tube for damage, cracks, dents or corro-
sion.
(b) Inspect the threads for damage.