1985 TOYOTA TERCEL oil type

FA.1O
' -'v7:'
FRONT AXLE AND SUSPENSION - Axle Hub
9. REMOVE OUTER OIL SEAL
Using SST, pull out oil seal.
ssT 09308-0001 0
1O. REPLACE WHEEL BEARING
h) First place the inner race (outside) of the bearing in
the bearing
(b) Using SST, press out the bearing.
SST 09228-22O2O and 09950-20015
(c) U$ilfi SST, prestffi a new bearing.
ssT 09309-3501 0
NOTE: There are two types of bearings; KOYO and NSK.
INSTALL OUTER OIL SEAL
h) Install the bearing inner race (outside) before install-
ing a pew oil seal.
(b) Using SST, drive the oil seal into the steering knuckle.
ssT 09515-35010
(c) Apply MP grease to the oit seal lip.
INSTALL DISC BRAKE DUST COVER ONTO STEERING
KNUCKLE WITH THREE BOLTS,
Apply liquid sealer to the dust cover and steering knuckle
connection before assembly.
INSTALL AXLE HUB
(a) Install new inner races into the inner bearing.
(b) Using SST, ggss in the inner race until it is tightty
against the sftlulder of the hub.
SST 09228-22O2O and O9310-35010
NOTE: Do not interchange the inner and outer races
when installing.
'.tfi
\
H
r
FE
11.
12.
13.
i
fr_, .,,iW;ffiqa-*L- L __

RA.1
REAR AXLE AND
SUSPENSION
(FWD}
TROUBLESHOOTING
REAR WHEEL ALIGNMENT
REAR AXLE HUB AND CARRIER
Sedan
Wagon
REAR SUSPENSION
Rear Shock Absorber
Suspension Arm
Strut Rod
(4wD)
TROUBLESHOOTING
REAR AXLE SHAFT
DIFFERENTIAL
FOUR LINK TYPE REAR SUSPENSION
Coil Spring and Rear Shock Absorber
Lateral Control Rod
Upper and Lower Control Arm
Rear Stabilizer Bar
Page
RA-2
RA-3
RA.5
RA-5
RA-l2
RA.l6
RA.l7
RA.20
RA.23
RA.24
RA-25
RA.28
RA'42
RA.43
RA.46
RA-48
RA.s1

REAR AXLE AND SUSPENSION - Four Link Type Rear Suspension (4WD) RA-43
Coil Spring and Rear Shock Absorber
(See page RA-421
REMOVAL OF COIL SPRING AND SHOCK
ABSORBER
1. JACK UP VEHICLE
Jack up the rear axle housing and support the body with
stands. Leave the jack under the rear axle.
2. REMOVE REAR SHOCK ABSORBER
(a) Remove the bolt holding the shock absorber to the
rear axle housing and disconnect the shock absorber.
(d Remove the nuts holding the shock absorber to the
body, and remove the shock absorber.
3. REMOVE STABILIZER BAR BUSHING BRACKETS
Remove the bolts holding the stabilizer bar bushing to the
rear axle housing.
4. DISCONNECT LATERAL CONTROL ROD FROM REAR
AXLE HOUSING
Remove the nut holding the lateral control rod to the rear
axle housing and disconnect the lateral control rod.

RA-/14 REAR AXLE AND SUSPENSION - Four Link Type Rear Suspension (4WD)
5. REMOVE COIL SPRING
(a) Begin to lower the rear axle housing.
NOTE: Be careful not to pull the brake line and parking
brake cable.
(b) While lowering the rear axle housing, remove the coil
spring and the upper and lower insulators.
INSTALLATION OF COIL SPRING AND
SHOCK ABSORBER
1. PUT LOWER INSULATOR ON AXLE HOUSING
2, PUT UPPER INSULATOR ON COIL SPRING
3. INSTALL COIL SPRING
4. CHECK POSITION OF LOWER INSULATOR
(a) Jack up the rear axle housing.
(b) Check that the lower insulator is installed correctly.
lf the insulator is not in correct position, reinstall the
coil spring.