1969 FORD MUSTANG torque

07-04-16
C-6 Automatic Transmission

07-04-16

INSTALLATION—

THUNDERBIRD

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification. Before

tightening the center bolt on the left

side,
make sure that the accelerator

linkage stop bracket is properly posi-

tioned so that the left upper bolt may

be installed later.

6. Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

7.
Raise the transmission and in-

stall the engine rear support and tor-

que the bolts to specification. Make

sure that the hand brake equalizer is

positioned properly.

8. Lower the transmission and re-

move the jack.

9. Install the engine rear support-

to-extension housing attaching bolts.

10.
Install the drive shaft.

11.
Connect the speedometer cable

to the extension housing.

12.
Position the starting motor on

the converter housing and secure it

with the two lower bolts.

13.
Install the torque converter-

to-flywheel attaching nuts and torque

them to specification.

14.
Install the converter housing

dust shield.

15.
Secure the frame side rail sup-

port brace with the attaching bolts

and lock washers. Torque the bolts to

specification.

16.
Connect the downshift rod to

the transmission downshift lever.

17.
Connect the vacuum diaphragm

hose to the upper end of the vacuum

tube.

18.
Using Tool T67P-7341-A, in-

stall a new grommet in the manual

lever. Then, secure the manual selec-

tor rod to the lever.

19.
Position the vibration absorber

to the transmission extension housing

and secure it with the three attaching

bolts.

20.
Connect the muffler inlet pipes

to the exhaust manifolds.

21.
Lower the vehicle and install

the two converter housing upper bolts

and torque them to specification.
22.
Install the starting motor upper

bolt.

23.
Place a new O-ring on the end

of the fluid filler tube and insert it in

the transmission case. Secure the tube

to the rear of the right cylinder head

with the attaching screw and lock

washer.

24.
Fill the transmission to the

proper level with the specified fluids.

25.
Adjust the manual and throttle

linkage as required.

REMOVAL-

CONTINENTAL MARK III

1.
Working from the engine com-

partment, lift the fluid filler tube dio-

stick from the transmission.

2.
Raise the vehicle on a hoist or

stands.

3.
Remove the dust shield from the

front lower end of the converter hous-

ing.

4.
Crank the engine until one of the

converter drain plugs is accessible.

Then, remove the plug.

5.
Crank the engine until the other

plug is at the bottom. Place a drain

pan to catch the fluid, then remove

the pan and allow the fluid to drain.

6. Remove the driveshaft.

7.
Remove the frame side rail sup-

port brace attaching bolts and remove

the brace.

8. After the fluid has been drained

from the converter, install the plug.

9. Place the drain pan under the

transmission pan and loosen the at-

taching bolts and allow the fluid to

drain. Finally remove all of the pan

attaching bolts except two, to allow

the oil to further drain. After the fluid

has drained, install two bolts on the

opposite side of the pan to temporari-

ly hold it in place.

10.
Remove the. converter-

to-flywheel attaching nuts.

11.
Disconnect the downshift link-

age from the transmission downshift

lever.

12.
Using tool T67P-7341-A, re-

move the selector rod from the manu-

al lever.

13.
Remove the two screws that at-

tach the shift rod bellcrank bracket to

the converter housing and remove the

bracket.

14.
Disconnect the vacuum dia-

phragm hose at the transmission.

15.
Disconnect the speedometer

cable from the extension housing and

place it to one side.

16.
Remove the two idler arm

bracket retaining bolts at the frame

side rail and allow the linkage to

hang.
17.
Disconnect the starter cable

from the terminal on the starter. Re-

move the starter attaching bolts and

remove it from the housing.

18.
Remove the clip securing the oil

cooler lines to the support bracket.

19.
Disconnect the two oil cooler

lines from the right side of the trans-

mission.

20.
Disconnect the muffler inlet

pipes at the exhaust manifolds and

allow the pipes to hang.

21.
Remove the vibration absorber

from the extension housing.

22.
Remove the engine rear support

to extension housing attaching bolts.

23.
Place a transmission jack under

the transmission and raise it just

enough to remove the weight from the

support.

24.
Remove the two support attach-

ing bolts and remove the support.

25.
Lower the jack and secure the

transmission to the jack with a safety

chain.

26.
Remove the bolt that secures

the filler tube to the rear of the right

cylinder head and lift the tube from

the transmission case.

27.
Remove the six converter

housing-to-cylinder block attaching

bolts.

28.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

29.
Remove the converter and

mount the transmission in a holding

fixture.

INSTALLATION—

CONTINENTAL MARK III

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification

6. Remove the jack safety chain

from the transmission.

7.
Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

8. Install a new O-ring on the lower

end of the fluid filler tube. Dip the

O-ring in clean automatic transmis-

sion fluid and insert the tube in the

transmission case. Install the attach-

ing bolt.procarmanuals.com

07-04-17
C-6 Automatic Transmission
07-04-17

9. Raise the transmission and in-

stall the engine rear support and tor-

que the bolts to specification.

10.
Lower the transmission and re-

move the jack.

11.
Install the engine rear support-

to-extension housing attaching bolts.

12.
Install the drive shaft.

13.
Connect the speedometer cable

to the extension housing.

14.
Connect the muffler inlet pipes

to the exhaust manifolds.

15.
Position the starting motor on

the converter housing and secure it

with the attaching bolts. Connect the

cable to the terminal on the starter.

16.
Position the idler arm bracket

to the frame side rail and install the

attaching bolts.

17.
Install the torque converter-

to-flywheel attaching nuts and torque

them to specification.

18.
Install the converter housing

dust shield.

19.
Secure the frame side rail sup-

port brace with the attaching bolts

and lock washers. Torque the bolts to

specification.

20.
Connect the downshift rod to

the transmission downshift lever.

21.
Using Tool T67P-7341-A, in-

stall a new grommet in the manual

lever. Then, secure the manual selec-

tor rod to the lever.

22.
Connect the vacuum hose to the

vacuum diaphragm.

23.
Install the oil cooler line retain-

ing clip at the transmission support.

24.
Position the vibration absorber

to the transmission extension housing

and secure it with the three attaching

bolts.

25.
Lower the vehicle.

26.
Fill the transmission to the

proper level with the specified fluids.

27.
Adjust the manual and throttle

linkage as required.

REMOVAL-

LINCOLN CONTINENTAL

1.
Raise the hood and remove the

transmission dipstick.

2.
Raise the vehicle on a hoist. Re-

move the bolt that secures the trans-

mission filler tube to the cylinder

head.

3.
Remove the bolts that attach the

reinforcement plate at the rear of the

transmission oil pan and remove the

plate.

4.
Remove the three bolts that at-

tach the manual and downshift control

rod splash shield to the side rail and

remove the shield.
5.
Place a drain pan under the

transmission. Loosen all transmission

pan attaching bolts and allow the fluid

to drain. Remove the bolts from the

rear and both sides of the pan to

allow further drainage; then, finally

remove the pan. After all fluid has

been drained, install the pan using

four attaching bolts.

6. Remove the two bolts that attach

the cover to the lower end of the con-

verter housing.

7.
Remove the two front support

bracket bolts at the converter housing.

8. Remove the two drain plugs

from the converter and allow it to

drain.

9. Remove the four nuts that attach

the converter to the flywheel.

10.
Lift the fluid filler tube from

the transmission case.

11.
Remove the two idler arm

bracket bolts from the frame side rail

and allow the idler arm to hang free.

12.
Disconnect the starter cable

from the starter. Remove the starter

attaching bolts and remove the starter.

13.
Disconnect the oil cooler lines

from the transmission.

14.
Disconnect the vacuum hose

from the diaphragm.

15.
Loosen the parking brake ad-

justing nut at the equalizer and re-

move the retracting spring. Disconnect

the rear brake cables and remove the

equalizer from the bracket.

16.
Disconnect the speedometer

cable from the extension housing.

17.
Disconnect the drive shaft from

the transmission flange and position

the shaft out of the way.

18.
Disconnect the downshift rod

from the transmission downshift lever.

19.
Using tool T67P-7341-A, re-

move the manual selector rod from

the manual lever.

20.
Remove the lower bellcrank at-

taching bolts and remove the bell-

crank.

21.
Pry the upper bellcrank out of

the converter housing and allow it to

hang free.

22.
Remove the cooler lines from

the clip at the cylinder head.

23.
Remove the converter housing-

to-cylinder block lower attaching

bolts.

24.
Remove the two nuts that at-

tach the engine rear mounts to the

crossmember.

25.
Place a transmission jack under

the transmission and raise it just high

enough to remove the weight from the

crossmember.

26.
Remove the engine rear

support-to-extension housing attaching

bolts and remove the supports.
27.
Remove the crossmember-

to-frame attaching nuts and remove

the crossmember.

28.
Secure the transmission to the

jack with the safety chain. Lower the

transmission and remove the upper

converter housing-to-cylinder block at-

taching bolts.

29.
Move the transmission away

from the cylinder block.

30.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

31.
Remove the converter and mount

the transmission in a holding fixture.

INSTALLATION-

LINCOLN CONTINENTAL

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with those in the flywheel.

5.
Move the transmission toward the

cylinder block until they contact each

other. Install and torque the attaching

bolts to specification.

6. Secure the converter to the fly-

wheel with the four attaching nuts.

Torque the nuts to specification.

7.
Secure the converter access cover

to the converter housing with the at-

taching bolts.

8. Secure the two front support

brackets to the converter housing with

the attaching bolts.

9. Raise the transmission high en-

ough to position the crossmember. In-

stall the bolts, but do not tighten at

this time.

10.
Secure the engine rear support

to the extension housing and torque

the bolts to specification. At this time,

install and torque the crossmember-

to-frame attaching nuts to specifica-

tion.

11.
Lower the transmission and in-

stall the engine rear support-

to-crossmember attaching nuts and

plates.
Torque the •"its to specifica-

tion. Remove the transmission jack.

12.
Install the upper bellcrank in

the left side of the converter housing.

13.
Position the lower bellcrank to

the transmission and floor pan and se-

cure it with the two attaching bolts.

14.
Connect the downshift rod to

transmission downshift lever.

15.
Using tool T67P-7341-A, install

a new grommet in the manual lever.

Then, secure the manual selector rod

to the lever.procarmanuals.com

07-04-18
C-6 Automatic Transmission
07-04-18

16.
Position the manual and down-

shift control rod splash shield to the

frame side rail and secure it with the

attaching bolts.

17.
Connect the speedometer cable

to the extension housing.

18.
Connect the vacuum hose to the

vacuum diaphragm and secure with a

clamp.

19.
Connect the two oil cooler lines

to the fittings on the right side of the

case.
20.
Install the cooler lines under

the clip at the cylinder head.

21.
Position the reinforcement plate

and torque the attaching bolts.

22.
Install the equalizer and park-

ing brake cables. Install the equalizer

lever retracting spring.

23.
Install the drive shaft.

24.
Install a new seal on the filler

tube and install it in the transmission

case.
Secure the filler tube to the cyl-

inder head.
25.
Install the starting motor and

connect the cable.

26.
Install the idler arm bracket-

to-frame side rail.

27.
Lower the vehicle.

28.
Fill the transmission to the cor-

rect level with the specified fluid.

29.
Adjust the manual and throttle

linkage as required.

MAJOR REPAIR OPERATIONS

DISASSEMBLY OF

TRANSMISSION

1.
Mount the transmission in hold-

ing fixture T64L-6001-A (Fig. 22).

2.
Remove the 17 fluid pan attach-

ing bolts. Remove pan and gasket.

3.
Remove the 8 valve body attach-

ing bolts (Fig. 23). Lift the valve body

from the transmission case.

4.
Attach a dial indicator to the

front pump as shown in Fig. 24. In-

stall tool T61L-7657-B in the exten-

sion housing to center the shaft.

5.
Pry the gear train to the rear of

the case and at the same time, press

the input shaft inward until it bottoms

(Fig. 24). Set the dial indicator to

read zero.

6. Pry the gear train forward (Fig.

24) and note the amount of gear train

end play on the dial indicator. Record

the end play to facilitate assembling

the transmission. Remove the dial in-

dicator from the pump and the tool

from the extension housing.

7.
Remove the vacuum diaphragm,

rod and the primary throttle valve

from the case. Slip the input shaft out

of the front pump.

8. Remove the front pump attach-

ing bolts. Pry the gear train forward

as shown in Fig. 25 to remove the

pump.

9. Loosen the band adjustment

screw and remove the two struts.

10.
Rotate the band 90 degrees co-

unterclockwise to align the ends with

the slot in the case (Fig. 26). Slide the

band off the reverse-high clutch drum.

11.
Remove the forward part of the

gear train as an assembly as shown in

Fig. 27.

12.
Remove the large snap ring that

secures the reverse planet carrier in

the low-reverse clutch hub. Lift the

planet carrier from the drum.

13.
Remove the snap ring (Fig. 28)

that secures the reverse ring gear and
D16Q3-B

FIG. 22—Transmission Mounted in Holding Fixture

hub on the output shaft. Slide the ring

gear and hub off the shaft.

14.
Rotate the low-reverse clutch

hub in a clockwise direction and at

the same time, withdraw it from the

case.

15.
Remove the reverse clutch snap

ring from the case, then remove the

clutch discs, plates and pressure plate

from the case.

16.
Remove the extension housing

attaching bolts and vent tube from the

case.
Remove the extension housing,

and gasket.

17.
Slide the output shaft assembly

from the transmission case.
18.
Remove the distributor sleeve

attaching bolts and remove the sleeve,

parking pawl gear and the thrust

washer.

If the thrust washer is staked in

place, use a sharp chisel and cut off

the metal from behind the thrust

washer. Be sure to clean the rear of

the case with air pressure or a suitable

solvent to remove any metal particles.

19.
Compress the reverse clutch pis-

ton release spring with tool T65P-

77515-A (Fig. 29). Remove the snap

ring. Remove the tool and the spring

retainer.procarmanuals.com

07-04-20

C-6 Automatic Transmission

07-04-20

SNAP RING

LOW-REVERSE

CLUTCH PISTON

Tool -

T6SL-77515-A
RETAINER Toof - T65L- 77575- A

D1610-A

FIG. 29—Compressing Reverse Clutch Spring

AIR NOZZLE

Tool- 7000- DD

LOW- REVERSE CLUTCH

APPLY PASSAGE

D1611-A

FIG. 30—Removing Low-Reverse

Clutch Piston
20.
Remove the one-way clutch

inner race attaching bolts from the

rear of the case. Remove the inner

race from inside of the case.

21.
Remove the reverse clutch pis-

ton from the case as shown in Fig. 30.

PARTS REPAIR OR

REPLACEMENT

During the repair of the sub-

assemblies, certain general instructions

which apply to all units of the trans-

mission must be followed. Following

these instructions will avoid unneces-

sary repetition.

OUTER

MANUAL LEVER

AND SHAFT

PARKING

PAWL ACTUATING

ROD

D1612-A

FIG. 31—Downshift and Manual Linkage

7"oo/ - 77288

D1613-A

FIG. 32—Installing Manual Lever

Seal
All transmission parts must be

handled carefully to avoid nicking or

burring the bearing or mating surfa-

ces.

Lubricate all internal parts of the

transmission with clean automatic

transmission fluid before assembling

them.

Do not use any other lubricants ex-

cept on gaskets and thrust washers.

These may be coated with vaseline to

facilitate assembly. Always use new

gaskets and seals when assembling a

transmission.
Tighten all bolts and screws to the

recommended torque as outlined in

the Specification Section.

TRANSMISSION CASE

AND LINKAGE

Downshift and Manual

Linkage

1.
Remove the nut and lock washer

that secures the outer downshift lever

to the transmission and remove the

lever.

2.
On a Mustang or Cougar, re-

move the two bolts that secure the

neutral safety switch to the case. In-

sert a screwdriver between the switch

and case as close as possible to the

shaft. Gently pry the switch from the

case.

3.
Slide the downshift lever out

from the inside-of the case (Fig. 31).

Remove the seal from the recess in

the manual lever shaft.

4.
Remove the C-ring that secures

the parking pawl actuating rod to the

manual lever. Remove the rod from

the case.

5.
Remove the nut that secures the

inner manual lever to the shaft. Re-

move the inner lever from the shaft.

Slide the outer lever and shaft from

the case.

6. Remove the seal from the case

with Tools T59L-1OO-B and T58L-

101-A or 7600-E.

7.
Dip the new seal in transmission

fluid and install it in the case as

shown in Fig. 32.

8. Slide the outer manual lever and

shaft in the transmission case.

9. Position the inner lever on the

shaft and install the attaching nut.

Tighten the nut to specification. In-

stall the parking pawl actuating rod

and secure it to the inner manual lever

with a C-washer.

10.
Install a new downshift lever

seal in the recess of the outer lever

shaft. Slide the downshift lever and

shaft into position.

11.
On a Mustang or Cougar, posi-

tion the neutral switch on the manual

lever and secure it with the two at-

taching bolts. Leave the attaching

bolts loose to adjust the switch after

installing the control valve.

12.
Place the outer downshift lever

on the shaft and secure it with a lock

washer and nut.procarmanuals.com

07-04-24

C-6 Automatic Transmission

07-04-24

CONVERTER PRESSURE RELIEF VALVE

THROTTLE PRESSURE

RELIEF BALL1/4 INCH

DIA. AND SPRING

CONVERTER

PRESSURE

RELIEF

SPRING

2-3 SHIFT

CHECK VALVE

D 1765-C

FIG. 39—Converter Pressure Relief Valve, Throttle Pressure Relief Valve,

and
2-3
Shift Check Valve Locations

FRONT PUMP

Tool
-
7775-AS

Tool -
T50T-
100-A

or 73-760

Tool
-T63L- 77837 -A

D 1636 -A

FIG. 40—Removing Front Pump

Seal

4.
Carefully position
the
separator

plate,
new
gasket
and the
lower valve

body
on the
upper valve body
and in-

stall
and
torque
the
attaching bolts
to

specification.

5.
Secure
the
screen
to the
lower

valve body with
the
attaching bolts

and torque them
to
specification.

6. Place
the
cutback control valve

(Fig.
38) in the
valve body.

7.
Place
the
coasting regulator

valve
in the
body.

8. Place
the
spring
D2
shift valve

and
the 1-2
shift valve
in the
body.

9. Place
the
throttle modulator

valve
and
spring
and the 2-3
shift

valve
in the
valve body.
D 1637-A

FIG. 41—Installing Front Pump

Seal

10.
Place
the
spring
and the 2-3

backout valve
in the
valve body.

11.
Place
the two
springs
and the

intermediate servo accumulator valve

in
the
valve body.

12.
Place
the
intermediate servo

modulator valve
and
spring
in the

body.

13.
Carefully place
the
valve retain-

ing plate
on the
body
and
secure
it

with
the
eight attaching screws. Tigh-

ten
the
screws
to
specification.

14.
Place
the
throttle booster valve

and spring
in the
valve body. Place

the manual
low 2-1
scheduling valve

and spring
in the
valve body
and in-
stall
the
retaining plate. Torque
the

attaching screws
to
specification.

15.
Place
the
main regulator,
two

springs, pressure booster valve
and the

sleeve
in the
valve body.

16.
Install
the
pressure booster

plate
and
torque
the two
attaching

screws
to
specification.

17.
Place
the
manual valve
in the

valve body
and
install
the
detent plug,

spring
and the
retaining
pin in the

body.

FRONT PUMP

The front seal
can be
replaced after

the pump
has
been installed
on the

transmission (Figs.
40 and 41).

Disassembly

1.
Remove
the two
seal-rings
and

the selective thrust washer (Fig.
42).

2.
Remove
the
large square-cut seal

from
the
O.D.
of the
pump housing.

3.
Remove
the 5
bolts that secure

the pump support
to the
pump hous-

ing. Lift
the
support from
the
housing.

4.
Remove
the
drive
and the
driven

gear from
the
housing.

Assembly

1.
Install
the
drive
and
driven gears

in
the
pump housing. Each gear
has

an identification mark
on one
face.

The identification mark
on
each gear

must
be
toward
the
front
of the
pump

housing.

2.
Position
the
pump support
in the

pump housing
and
install
and
torque

the five attaching bolts
to
specifica-

tion.

3.
Carefully install
two new
seal

rings
on the
pump support. Make sure

that
the
ends
of the
rings
are
engaged

to lock them
in
place. Install
a new

square-cut seal
on the O.D. of the

pump housing.

4.
Install
the
selective thrust wash-

er. Make sure that
the
correct thick-

ness selective washer
is
being used
to

obtain
the
specified
end
play.

5.
Place
the
pump
on
converter

making sure that
the
drive gear enga-

ges
the
converter
hub.
Rotate
the

pump
to
make sure that
the
gears
ro-

tate freely.

REVERSE-HIGH CLUTCH

Disassembly

1.
Separate
the
drive train
as
shown

in
Fig. 43.
Remove
the
pressure plate

retaining snap ring
as
shown
in Fig.

44.procarmanuals.com

07-04-29
C-6 Automatic Transmission

07-04-29

FORWARD CLUTCH

CYLINDER-7D424
OUTER SEAL

7A548
DISC SPRING FORWARD PRESSURE INTERNAL SPLINE REAR PRESSURE

7B070

PLATE-7B066

PLATE-7B164 PLATE-7B066

INNER SEAL

377130894
PISTON

7A262 STEEL

RING

7D256
SNAP

RING

377127-S

FIG. 52—Forward Clutch Disassembled

DISC

SPRING
EXTERNAL SPLINE

PLATE-7B442

7oo/-

7000-DD
SELECTIVE

SNAP RING

377126-S

D 1635-A

FIG. 53—Removing or Installing Disc Spring

distributor into place on the shaft. In-

stall the snap ring to secure it. Make

sure that the snap ring is seated in the

groove.

3.
Position the governor on the dis-

tributor (Fig. 62) and secure them

with the attaching screws.

ASSEMBLY OF TRANSMISSION

1.
Place the transmission case in a

holding fixture.

2.
Position the low-reverse clutch

piston so that check ball is in the 6 o'

clock position (toward bottom of case)
and tap the piston into place in the

case with a clean rubber hammer.

3.
Hold the one-way clutch inner

race in position and install and torque

the attaching bolts to specification.

4.
Install a low-reverse clutch re-

turn spring in each pocket in the

clutch piston. Press the springs firmly

into the piston to prevent them from

falling out.

5.
Position the spring retainer over

the springs and position the retainer

snap ring in place on the one-way

clutch inner race.
D1632-A

D1901-A

FIG. 54—Removing Forward

Clutch Piston

CHECK BETWEEN SNAP RING

AND PRESSURE PLATE

1902-A

FIG. 55—Checking Forward

Clutch Clearance

PICK

SCREWDRIVER

D 1633-A

FIG. 56—Removing Sun Gear

Snap Ringprocarmanuals.com

07-04-30
C-6 Automatic Transmission
07-04-30

6. Install the compressing tool

shown in Fig. 29 and compress the

springs just enough to install the low-

reverse clutch piston retainer snap

ring.

7.
Install the snap ring, then re-

move the compressing tool.

8. Place the transmission case on

the bench with the front end facing

downward.

9. Position the parking gear thrust

washer and the gear on the case (Fig.

33).
Do not restake the thrust washer.

10.
Position the oil distributor and

tubes in place on the rear of the case.

Install and torque the attaching bolts

to specification.

11.
Install the output shaft, and

governor as an assembly.

12.
Place a new gasket on the rear

of the transmission case. Position the

extension housing on the case and in-

stall the attaching bolts. Torque the

attaching bolts to specification.

13.
Place the case in the holding

fixture.

14.
Align the low-reverse clutch hub

and one-way clutch with the inner

race at the rear of the case. Rotate

the low-reverse clutch hub clockwise

while applying pressure to seat it on

the inner race.

15.
Install the low-reverse clutch

plates,
starting with a steel plate and

following with friction and steel plates

alternately. Retain them with vaseline.

Refer to the Specifications Section for

the number of plates required. If new

composition plates are being used,

soak them in clean transmission fluid

for fifteen minutes before installation.

Install the pressure plate and the snap

ring. Test the operation of the low-

reverse clutch by applying air pressure

at the clutch pressure apply hole in

the case.

16.
Install the reverse planet ring

gear thrust washer and the ring gear

and hub assembly. Insert the snap

ring in the groove in the output shaft.

17.
Assemble the front and rear

thrust washers onto the reverse planet

assembly; retain with vasoline. Insert

the assembly into the ring gear and

install the snap ring.

18.
Set the reverse-high clutch on

the bench, with the front end facing

down. Install the thrust washer on the

rear end of the reverse-high clutch as-

sembly. Retain the thrust washer with

vaseline and insert the splined end of

forward clutch into the open end of

the reverse-high clutch so that the

splines engage the direct clutch fric-

tion plates (Fig. 43).

19.
Install the thrust washer and re-

tain it with vaseline, on the front end
FORWARD

SNAP

RING

377300-S
SUN
GEAR

7A348

•
INPUT

SHELL

7D064

\
THRUST

WASHER

7D066

-IT

REAR

SNAP

RING

377300-S

I)
1634-A

57—Input Shell and Sun Gear Disassembled

of the forward planet ring gear and

hub.
Insert the ring gear into the for-

ward clutch.

20.
Install the thrust washer on the

front end of the forward planet assem-

bly. Retain the washer with vaseline

and insert the assembly into the ring

gear. Install the input shell and sun

gear assembly.

21.
Install the reverse-high clutch,

forward clutch, forward planet assem-

bly and drive input shell and sun gear

as an assembly into the transmission

case.

22.
Insert the intermediate band

into the case around the direct clutch
GEAR

SNAP RING

HUB AND FLANGE
D1906-A

FIG. 58—Output Shaft Hub and

Ring Gear

LOW-REVERSE

CLUTCH
DRUM-

7D390

SPRING

RETAINER-

7D191

BUSHING
-

7E194

SPRING
-
7D170

ROLLER-7190

D 1928-A

FIG. 59—One-Way Clutch Disassembled

cylinder.Install the struts and then

tighten the band adjusting screw suffi-

ciently to retain the band.

23.
Place a selective thickness bronze

thrust washer on the rear shoulder of

the stator support and retain it with

vaseline. If the end play was not

within specification when checked prior
to disassembly, replace the washer with

one of proper thickness. Refer to

Specifications Section for selective

thrust washer thicknesses. Lay a new

gasket on the rear mounting face of

the pump and position on the case

being careful not to damage the large

seal on the O.D. of the pump hous-procarmanuals.com

07-04-31
C-6 Automatic Transmission

07-04-31

ing. Install six of the seven mounting

bolts and torque them to specifica-

tion.

24.
Adjust the intermediate band as

detailed in Section 2 and install the

input shaft with the long splined end

inserted into the forward clutch as-

sembly.

LOW-REVERSE

SPRING LOAD ON ROLLERS CLUTCH HUB

MUST BE IN A COUNTERCLOCKWISE

DIRECTION FOR INSTALLATION Q 192O A

FIG. 60—Installing One-Way

Clutch
25.
Install tool 4201-C at the sev-

enth pump mounting bolt (Fig. 24)

and check the transmission end play.

Remove the tool.

26.
Install the control valve in the

case,
making sure that the levers en-

gage the valves properly. Install the
primary throttle valve, rod, and the

vacuum diaphragm in the case.

27.
Install a new pan gasket and

the pan.

28.
Install the converter assembly.

29.
Install the transmission in the

vehicle.

PISTON

AND ROD
PISTON

COVER

Models

PGA-A3,

J3,
Z, AA

PGB-AD,
AE, Jl

PGB-F2/G2, H2

PGB-AF1,
AG, AH
Piston

Assembly

C6AP-7D021-C

C6AP-7D021-D
Cover

C6AP-7D027-A

C6AP-7D027-D
Diameter - Inches

A

2.075

2.342

2.477
' B

2.980

3.025

NONE
c

2.971

3.016

3.492
D

2.066

2.333

2.468

Models

PGC-B,
Cl
Piston and

Rod Assembly
Cover
Diameter
—
Inches

A

2.183
B

2.739
C

2.705
D

2.220

D 2037-B

FIG.
61
— Intermediate Servo Cover and Piston Dimensions

OUTPUT

SHAFT
GOVERNOR

D
1623
-A

FIG. 62—Output Shaft Disassembledprocarmanuals.com