1969 FORD MUSTANG section 18

02-02-10
Brake System

02-02-10

brake adjustment then connect the

parking brake cable to the parking

brake lever (Fig. 8).

4.
Install the shoe guide (anchor

pin) plate on the anchor pin when so

equipped.

5.
Place the cable eye over the an-

chor pin with the crimped side toward

the backing plate.

6. Install the primary shoe to an-

chor spring (Fig. 15).

H1391-A

FIG. 75—Retracting Spring

Installation

7.
Install the cable guide on the

secondary shoe web with the flanged

hole fitted into the hole in the second-

ary shoe web. Thread the cable

around the cable guide groove (Fig.

8).

It
is
imperative that
the
cable
be

positioned
in
this groove
and not be-

tween
the
guide
and the
shoe
web.

8.
Install the secondary shoe to an-

chor spring with the tool shown in

Fig. 15.

Be certain that
the
cable
eye is not

cocked
or
binding
on the
anchor
pin

when installed.
All
parts should
be
flat

on
the
anchor
pin.
Remove
the
brake

cylinder clamp.

9. Apply high-temperature grease

(MIC-100-A) to the threads and the

socket end of the adjusting screw.

Turn the adjusting screw into the ad-

justing pivot nut to the limit of the

threads and then back off 1/2 turn.

Interchanging
the
brake shoe
ad-

justing screw assemblies from
one
side

of
the
vehicle
to the
other would cause

the brake shoes
to
retract rather than

expand each time
the
automatic
ad-

justing mechanism operated.
To pre-

vent installation on the wrong side of

the vehicle, the socket end of the ad-

justing screw is stamped with an R or

L (Fig. 16). The adjusting pivot nuts

can be distinguished by the number of

grooves machined around the body of

the nut. Two grooves on the nut indi-

cate a right thread; one groove indi-

cates a left thread.
10.
Place the adjusting socket on

the screw and install this assembly be-

tween the shoe ends with the adjusting

screw toothed wheel nearest the sec-

ondary shoe.

11.
Hook the cable hook into the

hole in the adjusting lever. The adjust-

ing levers are stamped with an R or L

to indicate their installation on right

or left brake assembly (Fig. 16).

12.
Position the hooked end of the

ADJUSTING LEVER

IDENTIFICATION LINES

H1143-C

FIG. 16—Adjusting Screw
and

Lever Identification

adjuster spring completely into the

large hole in the primary shoe web.

The last coil of the spring should be at

the edge of the hole. Connect the loop

end of the spring to the adjuster lever

hole.

13.
Pull the adjuster lever, cable

and automatic adjuster spring down

and toward the rear to engage the

pivot hook in the large hole in the sec-

ondary shoe web (Fig. 8).

14.
After installation, check the ac-

tion of the adjuster by pulling the sec-

tion of the cable between the cable

guide and the anchor pin toward the

secondary shoe web far enough to lift

the lever past a tooth on the adjusting

screw wheel. The lever should snap

into position behind the next tooth,

and release of the cable should cause

the adjuster spring to return the lever

to its original position. This return ac-

tion of the lever will turn the adjusting

screw.one tooth.

If pulling the cable does not pro-

duce the action described, or if the

lever action is sluggish instead of posi-

tive and sharp, check the position of

the lever on the adjusting screw

toothed wheel. With the brake in a

vertical position (anchor at the top),

the lever should contact the adjusting

wheel 3/16 inch (plus or minus 1/32

inch) above the centerline of the

screw. If the contact point is below

this centerline, the lever will not lock

on the teeth in the adjusting screw

wheel, and the screw will not be turned
as the lever is actuated by the cable.

To determine the cause of this con-

dition:

a. Check the cable end fittings. The

cable should completely fill or extend

slightly beyond the crimped section of

the fittings. If it does not meet this

specification, possible damage is indi-

cated and the cable assembly should

be replaced.

b.
Check the cable length. On

Ford, Mercury, Meteor, Thunderbird,

Continental Mark III, and Lincoln

Continental models, the cable should

measure 11 1/8 inches (plus or minus

1/64 inch) from the end of the cable

anchor to the end of the cable hook.

On Fairlane, Montego, Falcon,

Mustang, and Cougar models the

cable should measure 8 13/32 inches

on 9 inch brakes or 9 3/4 inches on

10 inch brakes from the end of the

cable anchor to the end of the cable

hook.

c. Check the cable guide for dam-

age.
The cable groove should be paral-

lel to the shoe web, and the body of

the guide should lie flat against the

web.
Replace the guide if it shows

damage.

d. Check the pivot hook on the

lever. The hook surfaces should be

square with the body of the lever for

proper pivoting. Replace the lever if

the hook shows damage.

e. See that the adjusting; screw

socket is properly seated in the notch

in the shoe web.

WHEEL CYLINDER

DRUM BRAKE

REMOVAL '

1.
Remove the wheel and the drum.

2.
Remove the brake shoe assem-

blies,
following procedures outlined in

this section.

3.
Disconnect the brake line from

the brake cylinder Figs. 17 thru 21.

On
a
vehicle with
a
vacuum brake

booster,
be
sure
the
engine
is
stopped

and there
is no
vacuum
in the
booster

system before disconnecting
the hy-

draulic lines.

To disconnect the hose at a front

cylinder, loosen the tube fitting that

connects the opposite end of the hose

to the brake tube at a bracket on the

frame. Remove the horseshoe-type re-

taining clip from the hose and brack-

et, disengage the hose from the brack-

et, then unscrew the entire hose as-

sembly from the front wheel cylinder.

At a rear cylinder, unscrew the tubeprocarmanuals.com

02-02-16
Brake System

02-02-16

fitting that connects the tube to the

cylinder. Do not pull the metal tube

away from the cylinder. Pulling the

tube out of the cylinder connection

will bend the metal tube and make in-

stallation difficult. The tube will sepa-

rate from the cylinder when the cylin-

der is removed from the backing

plate.

4.
On all except the front wheels on

Ford, Mercury, and Meteor models,

remove the wheel cylinder attaching

bolts and lock washers and remove the

cylinder. On the front wheel of Ford,

Mercury and Meteor models, remove

the nut and washer that attaches the

cylinder to the anchor pin. Remove

the cylinder from the anchor pin.

INSTALLATION

Wipe the end(s) of the hydraulic

line to remove any foreign matter be-

fore making connections.

1.
On all models except Ford, Mer-

cury and Meteor, to install a front

wheel cylinder, position the cylinder to

the backing plate. Install the two lock

washers and attaching bolts. Torque

them to specifications.

On Ford, Mercury and Meteor

models, to install a front wheel cylin-

der, position the cylinder on the an-

chor pin against the backing plate. In-

stall the washer and cylinder attaching

nut on the anchor pin, and torque it

to specification. Lock the washer re-

tainer securely.

2.
Install a new copper gasket over

the hose fitting. Thread the hose into

the cylinder and tighten it to specified

torque.

3.
Engage the opposite end of the

hose to the bracket on the frame. In-

stall the horseshoe-type retaining clip,

and connect the brake tube to the

hose with the tube fitting nut. Tighten

the nut to specification with tool

1112-144.

4.
To install a rear wheel cylinder,

place the rear wheel cylinder into po-

sition. Enter the tubing into the cylin-

der, and start the tube fitting nut into

the threads of the cylinder.

5.
Secure the cylinder to the back-

ing plate by installing the attaching

bolts and lock washers.

6. Tighten the tube fitting nut to

specification with tool 1112-144.

7.
Install the links in the ends of

the wheel cylinder, install the shoes

and adjuster assemblies, and adjust

the shoes as outlined in this section.

8. Adjust the brakes (Part 2-2, Sec-

tion 2). Install the brake drum and

wheel. Bleed the brakes and centralize

the differential valve as outlined in

Part 2-1, Section 2.
BRAKE BACKING PLATE

DRUM BRAKE

REMOVAL

1.
Remove the wheel and brake

drum. Disconnect the brake line from

the brake cylinder.

2.
Remove the brake shoe and ad-

juster assemblies and the wheel cylin-

der as outlined in this section. On the

rear wheels, disconnect the parking

brake lever from the cable.

3.
If the rear backing plate is being

replaced, remove the axle shaft from

the applicable rear axle as outlined in

Group 4, Part 4-2— Rear Axle, Sec-

tion 2, disengage parking brake cable

retainer from backing plate. Remove

the backing plate and gasket.

If the front backing plate is being

replaced, remove the bolts and nuts

that secure the backing plate to the

front wheel spindle and remove the

plate and gasket.

INSTALLATION

If a rear backing plate is to be re-

placed, position a new rear backing

plate and gasket on the attaching

bolts in the axle housing flange. Insert

parking brake cable into backing plate

and secure retaining fingers. Install

the rear axle shaft for applicable rear

axle.
Refer to Group 4, Part 4-2 —

Rear Axle, Section 2 for the proper

installation procedure.

1.
If the front brake backing plate

is to be replaced, position a new front

backing plate and gasket to the wheel

spindle and install the attaching bolts

and nuts.

2.
Install the wheel cylinder and

connect the brake line as outlined in

this section.

3.
Install the brake shoe and ad-

juster assemblies as outlined in this

section. On a rear brake, connect the

parking brake cable to the lever.

4.
Adjust the brake shoes (Section

2),
and install the brake drums and

wheels. Bleed the brake system and

centralize the differential valve as out-

lined in Part 2-1, Section 2.

DISC BRAKE CALIPER

ASSEMBLY

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

Refer to Figs. 22 and 23.
BLEEDER SCREW FACING THIS DIRECTION^

BLEEDER SCREW

H 1641-A

FIG. 22—Floating Caliper

Installed

1.
Remove the front wheel cover.

Remove the wheel and tire assembly

from the hub and rotor assembly. Be

careful to avoid damage or interfer-

ence with the caliper splash shield or

bleeder screw fitting.

2.
Disconnect the brake line from

the caliper. Cap the hose to prevent

*he brake fluid from leaking from the

master cylinder.

3.
Remove the safety wire and the

two bolts that attach the caliper as-

sembly to the spindle.

4.
Lift the caliper assembly off the

rotor and place it on the bench.

Installation

1.
Position the caliper assembly on

the rotor, and mate the mounting bolt

holes in the caliper with those in the

spindle. It may be necessary to push

the caliper piston into the cylinder

bore to obtain clearance between the

shoe and lining assembly and the

rotor.

2.
Install the caliper to spindle at-

taching bolts and torque them to spe-

cification. The upper bolt must be

tightened first. Install the safety wire

on the bolts and twist the wire ends at

least five turns. Push the wire ends

against the spindle to avoid interfer-

ence with the brake hose and the

steering stop. Check to insure that the

rotor runs squarely and centrally be-

tween the two brake shoes.

3.
Position the brake hose fitting

with a new copper washer on each

side of the fitting on the caliper as-

sembly. Install the bolts and torque to

specification.

4.
Bleed the brake system and cen-

tralize the differential valve as out-

lined in Part 2-1. Check the masterprocarmanuals.com

02-02-19
Brake System

02-02-19

that the tabs on the shoe flanges seat

fully against the caliper bridges (Fig.

25).

2.
Install the caliper splash shield

and secure the shield to the caliper

with two retaining bolts (Fig. 4).

3.
Pump the brake pedal several

times until a firm pedal is obtained

and the shoe and lining assemblies are

properly seated.

4.
Install the wheel and tire assem-

bly on the hub and rotor assembly.

5.
Check and refill the master cyl-

inder reservoir with specified brake

fluid as required.

6. Road test the car.

It should not be necessary to bleed

the system after a shoe and lining re-

placement.

FRONT WHEEL HUB AND

ROTOR ASSEMBLY-

DISC BRAKES

REMOVAL

1.
Remove the wheel and tire from

the hub (Figs. 23 and 24). Be careful

to avoid damage or interference with

the bleeder screw fitting. On Lincoln

Continental models be careful to avoid

damage to the caliper splash shield or

transfer tube.

2.
Remove the caliper assembly

from the spindle and the rotor. If the

caliper does not require servicing, it is

not necessary to disconnect the brake

hose or remove the caliper from the

vehicle. Position the caliper out of the

way, and support it with a wire to

avoid damaging the caliper or stretch-

ing the hose. Insert a clean cardboard

spacer between the linings to prevent

the piston from coming out of the cyl-

inder bore while the caliper is re-

moved.

Handle the rotor and caliper assem-

blies in such a way as to avoid defor-

mation of the rotor and nicking,

scratching or contamination of the

brake linings.

3.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

4.
Remove the hub and rotor as-

sembly from the spindle.

INSTALLATION

1.
If the rotor is being replaced, re-

move the protective coating from the

new rotor with carburetor degreaser.

Pack a new set of bearings with speci-
fied grease (M-1C75B), and install the

inner bearing cone and roller assembly

in the inner cup. Pack grease lightly

between the lips of a new grease seal

and install the seal (Figs. 23 and 24).

If the original rotor is being in-

stalled, make sure that the grease in

the hub is clean and adequate, that

the inner bearing and grease seal are

lubricated and in good condition, and

that the rotor braking surfaces are

clean.

2.
Install the hub and rotor assem-

bly on the spindle.

3.
Lubricate and install the outer

wheel bearing, washer and adjusting

nut.

4.
Adjust the wheel bearings to

specification, and then install the nut

lock, cotter pin, and grease cap. The

wheel bearing adjustment is especially

important with disc brakes.

5. Mount the caliper assembly on

the spindle following the Disc Brake

Caliper Assembly Installation proce-

dure in this section.

DISC BRAKE ROTOR

SPLASH SHIELD

REMOVAL

1.
Remove the caliper and the hub

and rotor assembly as outlined under
Removal in the foregoing procedure

(it is not necessary to disconnect hy-

draulic connections).

2.
Remove the three bolts that at-

tach the splash shield to the spindle,

and remove the shield (Figs. 23 and

24).

3.
Remove and discard the splash

shield to spindle gasket.

INSTALLATION

1.
Install a new splash shield to

spindle gasket.

2.
If the shield is bent, straighten it

out before installation. Position the

shield to the mounting bracket, install

the attaching bolts, nuts and torque

them to specification.

3.
Install the hub and rotor assem-

bly and the caliper as outlined under

Installation in the foregoing proce-

dure.

DUAL MASTER CYLINDER—

NON POWER BRAKES

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 26.

BUSHING

HAIRPIN

RETAINER

BUSHING

STOPLIGHT SWITCH

13480
HI 637-A

FIG. 26—Dual Master Cylinder Installation— Non Power Brakes

Ford,
Mercury, and Meteorprocarmanuals.com

02-02-21
Brake System

02-02-21

INSTALLATION

CLUTCH ASSIST

SPRING

MASTER CYLINDER

2140

FIG. 28 —Dual Master Cylinder Installation—

Non Power Brake—Mustang and Cougar

inch of the top of the dual reservoirs.

Use Ford Brake Fluid- Extra Heavy

Duty-Part Number C6AZ-19542-A

for all brake applications. The brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluid for the

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for the proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.

DUAL MASTER CYLINDER-

POWER BRAKES

REMOVAL

1.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder (Figs. 29

thru 33).

2.
Remove the two nuts and two

lock washers attaching the master cyl-

inder to the brake booster assembly.

3.
Slide the master cylinder forward

and upward from the vehicle.
SHAFT

AUTOMATIC

TRANSMISSION

CLUTCH PEDAL

BUMPER STOP
H1638-A
1.
Before installing the mater cyl-

inder, check the distance t; m the

outer end of the booster ass;. ,ihi\

push rod to the master .>',nder

mounting surface. Turn the nu->h rod

adjusting screw in or out as required

to obtain the specified length. Refer to

Part 2-1, Section 2. Power Brake

Master Cylinder Push Rod Adjust-

ment for the proper procedure.

2.
Position the master cylinder as-

sembly over the booster push rod and

onto the two studs on the booster as-

sembly (Figs. 29 thru 37).

3.
Install the attaching nuts and

lock washers and torque them to spec-

ifications.

4.
Install the front and rear brake

tubes to the master cylinder outlet fit-

tings.

5.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top o\ the dual reservoirs.

Use Ford Brake Fluid Fxtra Heavy

Duty Part Number C6AZ-19542-A

(ESA-M6C25-A) for all brake appli-

cations. The extra htaw duty brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluids for the

disc brake svstem.

CLIP

W
'0 AIR CONDITIONING

BUSHING

SHAFT

BUSHING

BRAKE PEDAL

SPACER

H 1642-A

FIG. 29—Master Cylinder Installation-

Ford,
Mercury and Meteor
-Power Brake-procarmanuals.com

02-02-24
Brake
System

02-02-24

proportioning valve to the fender

apron and remove the proportioning

valve.

Installation

1.
Position the proportioning valve

to the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the pro-

portioning valve to the fender apron.

4.
Tighten the brake line tube nuts

at the proportioning valve to specifica-

tions.

5.
Bleed the brakes and centralize

pressure differential valve.

THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 20.

1.
Disconnect the two hydraulic

brake lines at the master cylinder.

2.
Remove the two nuts retaining

the master cylinder to the booster and

remove the master cylinder for clear-

ance.

3.
Disconnect the two brake lines at

the proportioning valve.

4.
Remove the bolt and nut retain-

ing the proportioning valve to the

pressure differential valve bracket and

remove the proportioning valve assem-

bly.

Installation

1.
Transfer the bracket to the new

proportioning valve.

2.
Position the proportioning valve

assembly to the pressure differential

valve bracket.

3.
Connect the two brake lines to

the proportioning valve. Do not tight-

en.

4.
Install the bolt and nut retaining

the proportioning valve to the pressure

differential valve bracket.

5.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

6. Position the master cylinder to

the booster and install the nuts retain-

ing the master cylinder to the booster.

7.
Connect the two brake lines at

the master cylinder and tighten the

tube nuts to specifications.

8. Bleed the brakes and centralize

the pressure differential valve.
LINCOLN CONTINENTAL

Removal

Refer to Fig. 21.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Loosen the bolt and nut on the

bracket retaining the proportioning

valve to the chassis.

3.
Remove the proportioning valve

from the bracket.

Installation

- 1. Position the proportioning valve

in the bracket and connect the two

brake lines. Do not tighten.

2.
Tighten the bolt and nut on the

bracket.

3.
Tighten the tube nuts on the

brake lines at the proportioning valve

to specifications.

4.
Bleed the brakes and centralize

the pressure differential valve.

PRESSURE METERING VALVE—

LINCOLN CONTINENTAL

REMOVAL

Refer to Fig. 21.

1.
Loosen the tube nuts connecting

the inlet and outlet tubes at the me-

tering valve, and remove the tubes.

2.
Remove the two screws retaining

the metering valve to the frame

crossmember, and remove the me-

tering valve. The metering valve is ser-

viced as an assembly only.

INSTALLATION

1.
Position the metering valve to

the frame crossmember, and install

the retaining screws.

2.
Connect the inlet and outlet

tubes to the metering valve, and tight-

en the tube nuts to specification.

BRAKE BOOSTER

REMOVAL

1.
Working from inside the\ vehicle

below the instrument panel, disconnect

the booster push rod from the brake

pedal assembly. To do this, proceed as

follows:

Disconnect the stop light switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light
switch off from the brake pedal pin

just far enough for the switch outer

hole to clear the pin, and then remove

the switch from the pin and booster

push rod. Be careful not to damage

the switch during removal. Slide the

booster push rod and the nylon wash-

ers and bushing off the brake pedal

pin (Figs. 29 thru 33).

2.
Open the hood and remove the

master cylinder from the booster. Se-

cure it to one side without disturbing

the hydraulic lines. It is not necessary

to disconnect the brake lines, but care

should be taken that the brake lines

are not deformed. Permanent defor-

mation of brake lines can lead to tube

failure.

3.
Disconnect the manifold vacuum

hose or hoses from the booster unit.

4.
Remove the booster-to-dash

panel attaching nuts or bolts (Figs. 29

thru 33). Remove the booster and

bracket assembly from the dash panel,

sliding the push rod link out from the

engine side of the dash panel.

5.
On Fairlane, Montego, and Fal-

con models, remove the push rod link

boot from the dash panel.

INSTALLATION

1.
On Fairlane, Montego and Fal-

con models, install the push rod link

boot in the hole in the dash panel as

shown in Fig. 23. Install the four

spacers on the mounting studs.

2.
Mount the booster and bracket

assembly to the dash panel by insert-

ing the push rod or push rod link in

through the hole and boot in the dash

panel. Install the bracket-to-dash

panel attaching lock nuts or bolts

(Figs.
29 thru 33).

3.
Connect the manifold vacuum

hose or hoses to the booster.

4.
Before installing the master cyl-

inder, check the distance from the

outer end of the booster assembly

push rod to master cylinder surface.

Turn the screw in or out to obtain the

specified length. Refer to Part 2-1,

Section 2, Power Brake Master Cylin-

der Push Rod Adjustment. Install the

master cylinder and torque the attach-

ing nuts to specifications.

5.
Working from inside the vehicle

below the instrument panel, connect

the booster push rod link to the brake

pedal assembly. To do this, proceed as

follows:

Install the inner nylon washer, the

booster push rod, and the bushing on

the brake pedal pin. Position the

switch so that it straddles the push

rod with the switch slot on the pedal

pin and the switch outer hole justprocarmanuals.com

02-02-25
Brake System

02-02-25

clearing the pin. Slide the switch com-

pletely onto the pin, and install the

nylon washer as shown in Figs. 29

thru 33. Be careful not to bend or de-

form the switch. Secure these parts to

the pin with the hairpin retainer. Con-

nect the stop light switch wires to the

connector, and install the wires in the

retaining clip.

BRAKE PEDAL

FORD, MERCURY

AND METEOR

Removal

1.
Disconnect the stop light switch

wires at the connector.

2.
Remove the hairpin retainer.

Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin,

and then lift the switch straight up-

ward from the pin. Be careful not to

damage the switch during removal.

Slide the master cylinder or booster

push rod and the nylon washers and

bushing off the brake pedal pin (Figs.

26 and 29).

3.
Remove the hairpin type retainer

and washer from the brake pedal

shaft, then remove the shaft, the brake

pedal and the bushings from the pedal

support bracket.

Installation

1.
Apply a coating of SAE 10 En-

gine oil to the bushings and locate

bushings in their proper places on the

pedal assembly and pedal support

bracket (Figs. 26 and 29).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft through the support

bracket and brake pedal assembly. In-

stall the retainer.

3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the nylon washer as

shown in Figs. 26 and 29. Be careful

not to bend or deform the switch. Se-

cure these parts to the pin with the

hairpin retainer.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.
5.
Check the Brake Pedal Free

Height and Travel Measurements,

Part 2-1, Section 1.

FAIRLANE, MONTEGO AND

FALCON—MANUAL-SHIFT

TRANSMISSION

Removal

1.
Remove the clutch pedal assist

spring.

2.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

3.
Disconnect the stop light switch

wires at the connector.

4.
Remove the switch retainer, and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.

5. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27 and 30).

6. Remove the self-locking pin and

washer from the clutch and brake

pedal shaft, then remove the clutch

pedal and shaft assembly, the brake

pedal assembly, and the bushings from

the pedal support bracket (Figs. 27

and 30).

Installation

1.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
Position the brake pedal to the

support bracket, then install the clutch

pedal and shaft assembly through the

support bracket and brake pedal as-

sembly. Install the spring clip (Figs.

27 and 30).

3.
Install the clutch pedal assist

spring.

4.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10

engine oil to the bushing.

5.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27 and 30. Secure

these parts to the pin with the
self-

locking pin.
6. Connect the stop light switch

wires to the connector, and install the

wires to the retaining clip.

7.
Adjust the clutch pedal free play

(Group 5) to specification, if required.

8. Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

MUSTANG AND COUGAR—

MANUAL-SHIFT

TRANSMISSION

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
Remove the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

3.
On non-power brakes, remove

the two cap screws retaining the mas-

ter cylinder to the dash panel and re-

move the two cap screws retaining the

brake pedal support bracket to the

dash panel. On power brakes remove

the two cap screws retaining the

booster to the dash panel.

4.
Working inside the vehicle, se-

cure the clutch pedal against the

bumper stop with a small C-clamp as

shown in Figs. 28 and 31.

5.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder or

booster push rod, bushing and nylon

washer from the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Figs. 28 and 31).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel. On power

brakes remove the nuts from the

brake booster studs.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Position the pedal and support

bracket assembly in a vise.

13.
Remove the C-clamp to release

the clutch pedal from its bumper stop

and pivot the pedal away from the

bumper.procarmanuals.com

02-02-26
Brake System

02-02-26

14.
Remove the clutch pedal assist

spring.

15.
On non-power brakes, remove

the retainer clip from the clutch and

brake pedal shaft, then remove the

clutch pedal and shaft assembly, the

brake pedal assembly, and the bush-

ings from the pedal support bracket.

On power brakes, remove the retainer

nut from the brake pedal shaft then

remove the pedal shaft, the brake

pedal assembly and the bushings from

the pedal support bracket.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
On non-power brakes, position

the brake pedal to the pedal support

bracket, then install the clutch pedal

and shaft assembly through the sup-

port bracket and brake pedal assem-

bly. On power brakes position the

brake pedal to the pedal support

bracket, then install the pedal shaft

and nut.

3.
Install the clutch pedal assist

spring and pivot the clutch pedal

against its bumper stop. Secure the

pedal to the stop with a small C-

clamp as shown in Figs. 28 and 31.

4.
Position the pedal support

bracket assembly to the dash panel,

and to the steering column retainer

studs.

5.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two attaching sheet

metal screws. On power brakes install

the nuts on the brake booster studs.

6. Install the two cap screws at-

taching the pedal support bracket to

the upper cowl bracket.

7. Install the cap screw attaching

the pedal support bracket to the top

inner cowl bracket (Figs. 28 and 31).

8. Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the stop light switch so that it

straddles the push rod with the switch

slot on the pedal pin and the switch

outer hole just clearing the pin. Slide

the switch completely onto the pin,

and install the outer nylon washer as

shown in Figs. 28 and 31. Secure

these parts to the pin with the
self-

locking retainer.

9. Connect the stop light switch

wires to the connector.

10.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10
engine oil to the bushing. Remove the

C-clamp from the clutch pedal.

11.
Working from the engine side

of the dash panel, on non-power

brakes, install the two cap screws at-

taching the pedal support bracket to

the dash panel. Then install the two

screws attaching the master cylinder

to the dash panel. On power brakes

install the cap screws retaining the

brake booster to the dash panel.

12.
Install the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

13.
Adjust the clutch pedal free

play (Group 5) to specification, if re-

quired.

14.
Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

15.
Connect the ground cable to the

battery.

FAIRLANE, MONTEGO,

FALCON, MUSTANG

AND COUGAR-

AUTOMATIC TRANSMISSION

Removal

1. Disconnect the stop light switch

wires at the connector.

2.
Remove the self-locking pin and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27, 28, 30 and 31).

3.
On all vehicles except Mustang

and Cougar with power brakes, re-

move the self-locking pin and washer

from the brake pedal shaft, then re-

move the shaft, the brake pedal as-

sembly and the bushings from the

pedal support bracket. On Mustang

and Cougar vehicles with power

brakes, remove the locknut and bolt

from the pedal. Remove the pedal as-

sembly from the support bracket (Fig.

3).

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly and pedal support

bracket (Figs. 27, 28, 30 and 31).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft or bolt through the

support bracket and brake pedal as-

sembly. Install the retainer or locknut.
3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin, and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27, 28, 30 and 31.

Secure these parts to the pin with the

self-locking pin.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

Check the Brake Pedal Free Height

and Travel Measurements, Part 2,

Section 1.

THUNDERBIRD
AND

CONTINENTAL MARK
III

Removal

1.
Loosen the booster mounting

nuts.

2.
Disconnect the stop light switch

wires at the connector.

3.
Remove the hairpin retainer.

Slide the stop light switch off from

the brake pedal pin just far enough

for
the
switch outer hole
to
clear
the

pin,
and then lift the switch straight

upward from the pin. Slide the master

cylinder push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Fig. 32).

4.
Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the pedal support

bracket, and remove the bushings.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly (Fig. 32).

2.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through

the support bracket and brake pedal

assembly. Install the pivot bolt nut

and torque to specifications.

3.
Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, install the

outer nylon washer as shown in Fig.

32.
Secure these parts to the pin with

the hairpin retainer.procarmanuals.com

02-02-34
Brake System

02-02-34

strument panel. Install the lower con-

trol panel retaining screws.

8. Install the windshield wiper con-

trol bezel and knob.

9. Working in the engine compart-

ment connect the wire harness and

vacuum hoses to the Automatic Tem-

perature Control box.

10.
Connect the battery cable.

11.
Raise the vehicle on a hoist.

12.
Connect the cable ball to the

equalizer and install the equalizer

lever return ^spring.

13.
Adjust the parking brake cable

tension.

14.
Lower the vehicle.

PARKING BRAKE ACTUATOR—

TO CONTROL CABLE

FORD, MERCURY

AND METEOR

Removed

1.
Raise the vehicle on a hoist.

2.
Loosen the actuator lever to

equalizer cable adjusting nut at the

equalizer (Fig. 34).

3.
Disconnect the cable ball from

the clevis on the actuator lever.

4.
Remove spring clip that retains

the cable to the frame.

5.
From inside of passenger com-

partment, remove spring clip that re-

tains the cable to the parking brake

control. Disconnect the cable ball

from the control assembly.

6. Remove the cable assembly from

the vehicle.

Installation

1.
Position the cable through the

provided openings and in the approxi-

mate final installation position.

2.
Install the hairpin retainer on the

cable at the frame crossmember.

3.
Connect the ball end of the cable

to the parking brake control. Install

the cable-to-control hairpin retaining

clip.

4.
Position the cable seal at the

dash panel, and slide the retaining clip

upward to seal the cable at the dash

opening.

5.
Connect the ball end of the cable

to the clevis on the actuator lever.

6. Adjust the parking brake (Part

2-1,
Section 2).

7.
Lower vehicle on hoist.
THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 37.

1.
Partially raise the vehicle.

2.
Back off the adjusting nut at the

equalizer to relieve the tension on the

cable.

3.
Remove the spring at the actua-

tor lever and disconnect the control

cable from the clevis on the lever.

4.
Remove the clip retaining the

control cable assembly to
thq*.
frame

bracket. B

5.
Attach a length of wire to the

control cable.

6. Working inside the vehicle re-

move two screws retaining the left

scuff plate.

7.
Remove one screw and remove

the left cowl side trim panel.

8. Remove the two screws retaining

the left air duct to the inner panel and

remove the air duct.

9. Remove the two screws retaining

the dimmer switch and position the

dimmer switch back out of the way.

10.
Remove the clip retaining the

cable assembly to the control and re-

move the cable ball from the control

clevis.

11.
Pull the cable up through the

opening in the dash panel and remove

the cable from the length of wire.

Installation

1.
Attach the cable to the length of

wire and pull the cable down through

the opening in the dash panel.

2.
Position the upper end of the

control cable to the control. Connect

the cable ball to the control clevis and

install the clip retaining the cable

housing to the control.

3.
Remove the length of wire from

the cable assembly and position the

cable in the frame bracket. Install the

retainer,

4.
Connect the cable ball to the

clevis on the actuator lever and install

the actuator lever spring.

5.
Adjust the parking brake.

6. Reposition the dimmer switch

and install the retaining screws.

7.
Position the air duct to the inner

panel and install the retaining screws.

& Position the cowl side trim panel

and install the retaining screw.

9. Install the two screws in the

scuff plate.
PARKING BRAKE

EQUALIZER TO CONTROL

CABLE

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 35.

1.
Make certain the parking brake

is fully released.

2.
Raise the vehicle on a hoist. Re-

move the two nuts that attach the

cable to the equalizer. Remove the

equalizer, spring seat and spring.

3.
Remove the hairpin retainer

holding the cable assembly to i:he body

bracket and remove the cable from

the slot in the bracket.

4.
Lower the vehicle partially.

5.
Remove the hairpin retainer

which retains the cable assembly to

the control.

6. Remove the cable bolt retaining

clip from the control clevis and dis-

connect the cable ball from the clevis.

7.
Pull the cable down through the

opening in the floor pan and frame

side rail.

Installation

1.
Route the new cable through

the frame side rail and up through

the opening in the floor pan. Pull the

cable up into position.

2.
Connect the cable ball in the con-

trol clevis.

3.
Insert the cable housing into

the control and install the hairpin re-

tainer.

4.
Raise the vehicle.

5.
Position the cable in the body

bracket and install the hairpin re-

tainer.

6. Position the spring, spring re-

tainer and equalizer on the cable and

install the two nuts.

7.
Adjust the parking brake.

MUSTANG AND COUGAR

Removal

Refer to Fig. 36.

1.
Make certain the parking brake

is fully released.

2.
Raise the vehicle on a hoist. Re-

move the two nuts that attach the

cable to the equalizer. Remove the

equalizer spring seat and spring.

3.
Remove the hairpin retainer

holding the cable assembly to the

body bracket and pull the cable out

of the side rail access holes.procarmanuals.com