1969 FORD MUSTANG air conditioning

02-02-21
Brake System

02-02-21

INSTALLATION

CLUTCH ASSIST

SPRING

MASTER CYLINDER

2140

FIG. 28 —Dual Master Cylinder Installation—

Non Power Brake—Mustang and Cougar

inch of the top of the dual reservoirs.

Use Ford Brake Fluid- Extra Heavy

Duty-Part Number C6AZ-19542-A

for all brake applications. The brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluid for the

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for the proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.

DUAL MASTER CYLINDER-

POWER BRAKES

REMOVAL

1.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder (Figs. 29

thru 33).

2.
Remove the two nuts and two

lock washers attaching the master cyl-

inder to the brake booster assembly.

3.
Slide the master cylinder forward

and upward from the vehicle.
SHAFT

AUTOMATIC

TRANSMISSION

CLUTCH PEDAL

BUMPER STOP
H1638-A
1.
Before installing the mater cyl-

inder, check the distance t; m the

outer end of the booster ass;. ,ihi\

push rod to the master .>',nder

mounting surface. Turn the nu->h rod

adjusting screw in or out as required

to obtain the specified length. Refer to

Part 2-1, Section 2. Power Brake

Master Cylinder Push Rod Adjust-

ment for the proper procedure.

2.
Position the master cylinder as-

sembly over the booster push rod and

onto the two studs on the booster as-

sembly (Figs. 29 thru 37).

3.
Install the attaching nuts and

lock washers and torque them to spec-

ifications.

4.
Install the front and rear brake

tubes to the master cylinder outlet fit-

tings.

5.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top o\ the dual reservoirs.

Use Ford Brake Fluid Fxtra Heavy

Duty Part Number C6AZ-19542-A

(ESA-M6C25-A) for all brake appli-

cations. The extra htaw duty brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluids for the

disc brake svstem.

CLIP

W
'0 AIR CONDITIONING

BUSHING

SHAFT

BUSHING

BRAKE PEDAL

SPACER

H 1642-A

FIG. 29—Master Cylinder Installation-

Ford,
Mercury and Meteor
-Power Brake-procarmanuals.com

03-11-01
Eaton Power Steering Pump

03-11-01

PART 3-11 Eaton Power Steering Pump

COMPONENT INDEX
MODEL APPLICATION

3
§>
"o

4

POWER STEERING PUMP

Cleaning and Inspection (See Part 03-01)

Description

N/A
N/A
N/A
N/A
N/A
N/A

N/A
N/A
11-01

N/A
11-01

Disassembly and Overhaul

N/A
N/A

N/A
N/A

N/A
N/A

N/A
N/A
11-03

N/A
11-03

Removal and Installation

N/A
N/A
N/A
N/A

N/A
N/A
N/A
N/A
11-01
N/A

11-01

POWER STEERING PUMP RESERVOIR

Removal and Installation

N/A
N/A
N/A

N/A
N/A
N/A

N/A

N/A

11-01
N/A

11-01

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

l
DESCRIPTION

The roller-type hydraulic pump,

driven by the crankshaft, draws auto-

matic transmission fluid down the res-

ervoir and provides fluid pressure for

the system. Steering gear lubrication
is also provided by the same fluid

from the reservoir. Within the pump

itself is a flow-control and pressure-

relief valve which governs the pres-
sures within the steering system ac-

cording to the varying conditions of

operation. After fluid has passed from

the gear, it returns to the reservoir.

REMOVAL AND INSTALLATION

POWER STEERING PUMP

REMOVAL

1.
Open the hood, and install fend-

er covers.

2.
If the vehicle is equipped with air

conditioning, loosen the compressor

adjusting and support bracket bolts

and remove the drive belt.

3.
Loosen the generator adjusting

and support bracket bolts, and remove

the drive belts.

4.
Remove the fan, pulley, and spa-

cer.

5.
Raise the vehicle.

6. Remove the crankshaft damper

bolt and washer. Remove the damper

with Tool 6306-AG. Remove the drive

key.

7.
Disconnect the pump inlet line at

the pump, and plug the end of the line

to prevent the loss of fluid. Disconnect

the pump pressure line at the pump.
8. Remove the pump-to-engine

front cover cap screws, and remove

the pump. Remove the seal from the

front cover.

INSTALLATION

1.
Install a new seal on the engine

front cover.

2.
Align the slot in the pump rotor

shaft with the drive key in the crank-

shaft, and slide the pump onto the

shaft. Install the pump-to-engine front

cover cap screws. Torque the cap

screws to specification.

3.
Connect the pump inlet line and

the pressure line.

4.
Install the damper drive key,

damper, washer and bolt. Torque the

bolt to specification.

5.
Install the fan, pulley, and spa-

cer. Install the generator drive belts.

Adjust the belt tension, and tighten

the adjusting and support bracket

bolts.
6. If the vehicle is equipped with air

conditioning, install the compressor

drive belt. Adjust the belt tension, and

tighten the adjusting and support

bracket bolts.

7.
Run the engine at idle speed,

and check the fluid level in the reser-

voir. If required, add the specified au-

tomatic transmission fluid. Turn on

the windshield wipers. Rotate the

steering wheel from stop to stop sever-

al times to bleed the air from the sys-

tem. Recheck the fluid level.

POWER STEERING PUMP

RESERVOIR

WITHOUT AIR

CONDITIONING

Removal

1.
Remove the reservoir cover andprocarmanuals.com

03-11-02
Eaton Power Steering Pump

03-11-02

gasket. Withdraw the fluid with a suc-

tion gun.

2.
Remove the reservoir bracket-

to-cylinder block upper cap screw and

the lower cap screw and spacer.

3.
Disconnect the reservoir infet line

and the outlet line at the reservoir,

and remove the reservoir.

Installation

1.
Connect the reservoir-to-pump

line (outlet line) at the reservoir, but

do not tighten the clamp.

2.
Attach the reservoir and bracket

to the cylinder block with the upper

cap screw and the lower cap screw

and spacer. Tighten the cap screws.

3.
Tighten the outlet line clamp at

the reservoir. Connect the reservoir

inlet line to the reservoir.

4.
Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.
WITH AIR CONDITIONING

Removal

1. Raise the front of the vehicle.

Remove the reservoir-to-pump line

(outlet line) clamp at the reservoir,

but do not disconnect the line at this

time.

2.
Disconnect the reservoir inlet line

at the reservoir.

3.
Remove the reservoir bracket to

the cylinder block upper cap screw.

Support the reservoir and remove the

lower cap screw and spacer.

4.
With a drain pan under the res-

ervoir, disconnect the outlet line hose

from the reservoir tube and allow the

fluid to drain.

5.
Remove the reservoir cover re-

taining nut and the cover. Position the

cover and the reservoir out of the way

and allow them to rest in the engine

compartment.

6. Lower the front of the vehicle.

Remove the fan shroud.

7.
Remove the reservoir and the
cover by manipulating them through

the opening between the radiator and

the compressor drive belt.

Installation

1.
Position the reservoir in the en-

gine compartment. Loosely attach the

reservoir and bracket to the cylinder

block with the upper cap screw.

2.
Install the fan shroud, then raise

the front of the vehicle.

3.
Connect the reservoir-to-pump

line (outlet line) at the reservoir.

4.
Install the reservoir bracket-

to-cylinder block lower cap screw and

spacer. Tighten both the upper and

the lower cap screws.

5.
Connect the reservoir inlet line at

the reservoir. Install the clamps on

both lines. Lower the car, and install

the reservoir cover and attaching nut.

6. Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.

3 MAJOR REPAIR OPERATIONS

INSULATOR (2)

WASHER (2)

MOUNTING BOLT (2)

COVER

BOLT (7)
DOWEL
PIN (2)

ROTOR

ROTOR
SHAFT

COVER
SEAL
PLUG

O RING

VALVE
ASSEMBLY

VALVE
SPRING

INSULATOR

HOUSING

CAM RING

PRESSURE
PLATE
,
PUMP

i
HOUSING

SEAL

ROLL

PIN

INSULATOR

RETAINER
RING
TUBE SEAT

O RING

SCREW
(2)

G12O8-B

FIG.
1
— Power Steering Pumpprocarmanuals.com