1967 CHEVROLET CAMARO maintenance

[x] Cancel search: maintenance

trip computer ECO mode fuel consumption technical data width change key battery

Load previous 8 pages

Page 477 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
STEERING 9-37

NUT

Fig.
69—Control Valve Ball Stud Seal Replacement

(Service Type)

4.
Center the ball stud, seal and clamp at opening in

adapter housing, then install spacer, bolt and nut.

R

Page 479 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
STEERING 9-39

4.
Remove cotter pin, nut and ball stud at relay rod.

5. Remove the power cylinder from the vehicle.

Inspection

1.
Inspect the seals for leaks; if leaks are present,

replace the

STEERING 9-39

4.
Remove cotter pin, nut and ball stud at relay rod.

5. Remove the power cylinder from the vehicle.

Inspection

1.
Inspect the seals for leaks; if leaks are present,

replace the seals using the procedure outlined under

"Disassembly."

2.
Examine the brass fitted hose connection seats for

cracks or damage and replace if necessary.

3.
For service other than ball seat or seal replacement

and ball stud removal, replace the power cylinder.

4.
Check the frame bracket parts for wear.

Disassembly

1.
To remove the piston rod seal remove the snap ring;

then pull out on the rod, being careful not to spray

oil.

2.
Remove the piston rod scraper and scraper element,

back up washer and piston rod seal from the rod.

3.
At the ball stud end of the cylinder, remove the ball

stud seal.

4.
Remove the snap ring retaining the end plug with the

lube fitting.

5. Push on the end of the ball stud and remove the end

plug, spring, spring seat and ball stud.

6. Remove the "O" ring seal from the top lip of the

power cylinder ball stud opening.

7. If the ball seat is to be replaced, it must be pressed

out using Tool J-8937.

Assembly

1.
Reassemble the piston rod seal components by re-

versing the disassembly procedure. Apply a thin
coat of Lubriplate or equivalent on the inner sur-

faces of the seal and scraper before assembly.

2.
Reverse the disassembly procedure when reassem-

bling the ball stud.

3.
In each case be sure that the snap ring is securely,

seated in the ring groove.

Installation

1.
Install the power cylinder on the vehicle by reversing

the removal procedure.

2.
Reconnect the two hydraulic lines, fill the system

with fluid and bleed out air using the procedure out-

lined under "Maintenance and Adjustments." Grease

ball joint.

POWER STEERING HOSES

When servicing the power steering hoses be sure to

align the hoses in their correct position as shown in

Figure 71. On Chevelle models with 396 engine, install

the upper hose so that there is at least .6 inch clearance

between the hose and the Delcotron or the inner fender

skirt.

It is important that the power steering hoses be in-

stalled correctly. Hoses installed out of position may be

subjected to chafing or other abuses during sharp turns.

Always make hose installations with front wheels in

straight ahead position. Do not twist hoses unneces-

sarily during installation.

CAUTION: Do not start engine with any power

steering hose disconnected.

CHEVROLET CHASSIS SERVICE MANUAL

Page 481 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
SECTION 10

WHEELS AND TIRES

INDEX

Page

General Description
10-1

Maintenance
and
Adjustments
.............. 10—1

Tires
10-1

Pressures . 10-1

Inspection 10-1

Wear 10-1

Rotation 10-4

N

SECTION 10

WHEELS AND TIRES

INDEX

Page

General Description
10-1

Maintenance
and
Adjustments
.............. 10—1

Tires
10-1

Pressures . 10-1

Inspection 10-1

Wear 10-1

Rotation 10-4

Noise 10-4

Cleaning 10-4

Change (W/Wheels) 10-4

Wheels 10-5

Static Balancing (w/Tire) 10-5
Page

Dynamic Balancing (w/Tire) . 10-5

Run Out (w/o Tire) 10-5

Cleaning 10-5

Service Operations 10-5

Tires 10-5

Removal 10-5

Installation 10-5

Repair 10^6

Wheels . 10-6

Valve Assembly 10-6

Repair (Rim) 10-7

GENERAL DESCRIPTION

WHEELS

Chevrolet, Chevelle, Camaro, Chevy n, and Corvette

are base equipped with welded steel wheels. Five studs

with nuts fasten each wheel to the front hub or rear axle

flange. Disc brake equipped vehicles (except Chevrolet

and Corvette) require special 14 inch diameter wheels

with a revised design for clearance, Chevrolet disc brake

equipped vehicles have 15 in. diameter wheels as do all

Corvettes.

Chevrolet station wagons, Chevelle Super Sport 396,

Corvette and Camaro Super Sport 350 are base equipped

with 6 in. width wheels. All other vehicles have 5 in.

width wheels, except Chevy n 100, 300 and 500 Series

Sedans, which have 4 in. width wheels.

Do not install 6 inch width wheels or snow chains on

Chevrolets equipped with rear fender skirts.

TIRES

The factory installed tires on Chevrolet passenger

cars are selected to provide the best all around tire

performance for all normal operation. They are de-

signed to operate satisfactorily with loads up to and in-

cluding the specified full rated load capacity of the
automobile when inflated as recommended in the Vehicle

Capacity Rating and Recommended Tire Inflation Pres-

sures Table (see Specifications).

Optional Oversize and 8-Ply Rating Tires

{Chevrolet and Chevelle Only)

Oversize or 8-ply rating tires are not necessary on

passenger cars for normal requirements. However, an

extra margin of tire service is available when these

options are used at loads up to and including full rated

load.

Optional oversize 4-ply rating and/or 8-ply rating

tires are available on models as indicated in the Tire

Usage Chart (see Specifications). On some models (ex-

ample—Station Wagon), space limitations do not permit

the use of a larger size tire; hence, the 8-ply rating

tire is an available option.

In either case, these tires are applicable to extended

operation at or near full rated load or for trailer towing

when an extra margin of tire service is desired. How-

ever, use of a larger tire or an 8-ply rating tire should

not be construed as permitting an increase in the full

rated vehicle load (see Specifications).

MAINTENANCE AND ADJUSTMENTS

TIRES

Inflation Pressures

To ensure the proper tire inflation pressure for the

owners particular requirements follow the recommenda-

tions in the Vehicle Capacity Rating and Recommended

Tire Inflation Pressures Table (seeSpecifications). Keep

tires properly inflated, and check inflation pressures

periodically. This will ensure the best tire life and riding

comfort, over the full range of driving conditions.
Inspection

Every few thousand miles and at each lubrication, tires

should be checked for sharp objects or stones in the

tread. H tire is punctured, it should be repaired using

one of several repair kits available through tire manu-

facturers1 outlets.

Wear

Misalignment

This is wear due to excessive toe-in or toe-out. In

CHEVROLET CHASSIS SERVICE MANUAL

Page 488 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
SECTION 11

CHASSIS SHEET METAL

CONTENTS OF THIS SECTION

Chevrolet and Chevelle 11-1

Chevy II . . 11.-11

Camaro 11-19

Corvette (See Section IB)

Special Tools 11-25

CHEVROLET AND CHEVELLE

INDE

SECTION 11

CHASSIS SHEET METAL

CONTENTS OF THIS SECTION

Chevrolet and Chevelle 11-1

Chevy II . . 11.-11

Camaro 11-19

Corvette (See Section IB)

Special Tools 11-25

CHEVROLET AND CHEVELLE

INDEX

Page

General Description 11-1

Maintenance and Adjustments •. il-1

Hood Adjustment 11-1

Hinges 11-1

Bumpers 11-1

Catch Assembly and Lock 11-1

Fenders 11-4

Sheet Metal 11-4

Component Part Replacement 11-4

Battery Tray 11-4
Page

Radiator Support 11-4

Fender Assembly . . 11-4

Skirt 11-4

Trim 11-5

Hood Assembly 11-6

Lock and Catch 11-7

Trim and Insulation 11-7

Cowl Vent Grille 11-7

Rear Wheel Cover 11-7

Simulated Wood Grain Moulding . . . . 11-7

GENERAL DESCRIPTION

The new front end appearance of the 1967 Chevrolet

and Chevelle passenger cars affects the servicing and

replacement of the chassis sheet metal. Refer to Section

13 for Radiator and Grille service procedures, Section
14 for Bumpers, and Section 1A for Air Conditioning

components. Figures 1 and 2 illustrate the Chevrolet

and Chevelle sheet metal components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The alignment of the hood is controlled by the position

of the hood hinges and the height of the two bumpers lo-

cated one at each side of the radiator support. The ad-

justment at the hood lock must be made after the hinges

and bumpers are properly adjusted. To align the hood

and lock proceed as follows:

HOOD HINGE (Fig. 3)

NOTE:
The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a line around the entire hinge plate to be re-

positioned.
2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with the fender and grille top surfaces. Refer to Fig-

ures 4 and 5 for correct sheet metal adjustment dimen-

sions.

HOOD CATCH AND LOCK

The hood catch assembly (fig. 6) mounting holes are

slotted to provide adjustment for the hood lock bolt. Ad-

just the hood lock bolt until hood engages securely when

closed and hood bumpers are slightly compressed.

CHEVROLET CHASSIS SERVICE MANUAL

Page 498 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
CHASSIS SHEET METAL 11-11

CHEVY II

INDEX

Page

General Description 12

Maintenance and Adjustments 12

Hood ........ 13

Hinge 13

Bumpers 13

Catch Assembly . . . 13

Lock 13

Fenders . 13

Sheet

Page 499 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
CHASSIS SHEET METAL 11-12

GENERAL DESCRIPTION

The sturdy front end structure is formed by three

welded assemblies, the left and right hand fender skirts

and the radiator support panel. These unit

Page 505 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
CHASSIS SHEET METAL 11-18

b.
Check and adjust front wheel alignment as out-

lined in Section 3.

c. Check and adjust headlamp aiming as outlined in

Section 12.

HOOD ASSEMBLY

Hood may be removed

CHASSIS SHEET METAL 11-18

b.
Check and adjust front wheel alignment as out-

lined in Section 3.

c. Check and adjust headlamp aiming as outlined in

Section 12.

HOOD ASSEMBLY

Hood may be removed either with or without hinges.

To shorten aligning time, hood hinge plates may be lo-

cated by scribing a mark on hood and/or body which

outlines entire plate. See Maintenance and Adjustments -

Hood Hinge for hood adjustment procedure. Hood hinge

springs may be easily and safely removed and installed.

through the use of Tool J-9559 as follows:

1.
With hood opened only far enough to allow passage of

mechanic's arm between hood and fender, insert ends

of J-9559 (through bolt removed) between coils of

spring until barrel of tool contacts outer diameter

of spring.

2.
Open hood fully while still holding spring (with tool

installed) in hand; when hood is near fully opened

position, spring may be removed as shown in Figure

28.

3.
As soon as spring is removed, insert long bolt sup-

plied with J-9559 through holes in end of tool, pass-

ing it through spring, and install nut on bolt.

Spring may be removed from J-9559 or J-9559 may be

installed in a new spring by the following method:

1.
Place a closed 6 or 8 inch "C" clamp in a vise or

fasten it to a heavy bench top (bench should be fas-

tened to floor).

2.
Hook one end of spring in clamp and the other end

in hook of a hoist as shown in Figure 29.

3.
Stretch the spring enough to allow insertion of

J-9559. Install through bolt if spring is not to be

installed on hinge at once.

HOOD CATCH AMD LOCK (Fig. 19)

Removal

1.
Remove catch assembly as follows:

a. Remove screws retaining catch assembly to radi-

ator support.

b.
Remove screws retaining catch assembly to catch

support assembly.

c* Remove screws retaining catch assembly to grille

upper bar.

2.
Before removing hood lock plate from hood, locate

position on hood by scribing around base of lock

plate. Remove screws retaining lock plate to hood

and remove lock plate from vehicle.

Installation

1.
Install both catch and lock assemblies in reverse

order of removal procedure.

2.
Align as outlined under Maintenance and Adjust-

ments - Hood Catch.

HOOD TRIM

Crown Molding

Hood crown molding is retained by clips installed on

underside of hood. Clips may be removed by carefully

pressing them off molding mounting studs with screw

driver.
When installing a new molding, force clips onto mount-

ing studs as far as possible and then clench clips with

long-nosed pliers to eliminate gap between molding and

hood, as shown in Figure 30.

Emblem

The hood emblem is retained by four nuts which are

accessible from under the hood.

COWL VENT GRILLE

The cowl vent grille replacement procedure for Chevy

U is the same as for Chevrolet and Chevelle. Refer to

Chevrolet and Chevelle Cowl Vent Grille replacement

procedure and see Figure 16.

FRONT END ASSEMBLY

The Chevy n front end body design allows for removal

of the entire front end of the vehicle without disassembly

of front suspension of sheet metal. One man may remove

and transport the front end assembly using only a floor

jack placed under the crossmember and the vehicle front

wheels. Figure 31 illustrates the assembly in process

of removal with jack stand in position under rocker panel.

Proceed with removal
as.
follows:

Removal

1.
Remove hood assembly as outlined in this section.

2.
Remove engine assembly as outlined in Section 6.

On 4 cylinder models, replace crossmember.

3.
Raise car from floor and install jack stands as

shown in Figure 31.

4.
Remove pitman arm from steering gear as outlined

in Section 9.

5.
Remove steering gear mounting bolts from skirt

assembly.

6. Remove 4 bolts securing each skirt assembly to

lower dash brace.

7.
Remove fender-to-rocker extension mounting screws

and record shimming.

8. Remove brake hydraulic line and fuel line from right

hand skirt.

9. Position floor jack or equivalent under front cross-

member.

10.
Remove hydraulic line from main cylinder.

11.
Remove fender-to-cowl mounting screws and record

shimming.

12.
Remove upper skirt-to-dash mounting screws and

record shimming.

13.
Remove front end from vehicle as shown in Figure

31.

Inspection

If car has been involved in a collision, it is advisable

to carefully inspect cowl and dash area for damage. Pay

particular attention to welds, cage nuts, weld nuts and

skirt mounting surfaces. Cage and weld nuts may be

repaired by outright replacement (the best method), or

by the installation of spiral thread inserts. If the spiral

inserts are used, follow the instructions furnished by the

manufacturer. -

Installation

%, position front end assembly at upper dash mounts

and lower dash support, align screw holes with drift

punch and install all mounting screws and bolts

loosely; do not tighten until all screws and bolts are

started. Replace original shimming.

CHEVROLET CHASSIS SERVICE MANUAL

Page 506 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
5.

6.

7.

8.
2.
Install all fender mounting screws, replacing original

shimming. Refer to removal procedure for screw

location.

3.
Install hydraulic lines at main cylinder and right

hand skir

Load next 8 pages

Page: < prev 1-10 ... 25-32 33-40 41-48 49-56 57-64 65-72 next >

remote control reset sun roof check engine radio antenna ground clearance clock reset