1967 CHEVROLET CAMARO maintenance

HEATER
AND AIR
CONDITIONING
1A-13

AIR CONDITIONING

INDEX

Page

General Description
1A-13

Four-Season System
1A-13

Controls
1A-16

Comfortron System
. 1A-18

System Components
lA-19

Controls
1A-20

Universal System
. .
1A-21

Chevy
n
All-Weather System
•
1A-21

Corvette Four-Season System
. 1A-22

General Information
. . . 1A-26

Precautions
in
Handling R-12
1A-26

Precautions
in
Handling Refrigerant Lines
1A-28

Maintaining Chemical Stability
in the

Refrigeration System
1A-28

Gauge
Set 1A-29

Charging Station
IA-29

Leak Testing
the
System
1A-29

Vacuum Pump
1A-30

Availability
of
Refrigerant-12
. . 1A-30

Compressor
Oil 1A-31

Compressor Serial Number
1A-31

Inspection
and
Periodic Service
1A-31

Pre-Delivery Inspection
1A-31

6,000 Mile Inspection
1A-32

Periodic Service
, 1A-32

Installing Gauge
Set to
Check System Operation
....
1A-32

Performance Test
1A-32

Performance Data lA-r33

Comfortron System Operational Test
1A-33

Chevrolet Comfortron Tester
1A-34

Complete System Checks
1A-35

Maintenance
and
Adjustments ......
1A-37

Evaporator Comtrol Valve (POA)
.
1A-37
Page

Thermostatic Switch
1A-37

Expansion Valve
1A-41

Engine Idle Compensator
. . .
1A-42

Evacuating
and
Charging Procedures
1A-42

Purging
the
System
1A-42

Evacuating
and
Charging
the
System
1A-43

Checking
Oil . 1A-43

Component Replacement
and
Minor Repair
1A-45

Refrigerant Line Connections
1A-45

Repair
of
Refrigerant Leaks
1A-46

Preparing System
for
Replacement
of

Component Parts
. 1A-46

Foreign Material
in the
System
.
1A-47

Condenser
.
1A-48

Receiver-Dehydrator
1A-48

Evaporator
1A-49

Expansion Valve
1A-57

Evaporator Control Valve (POA)
1A-59

Thermostatic Switch
or
Blower Switch
. .
1A-59

All Weather-Pull Cable
1A-61

Blower Assembly
1A-62

Air Inlet Valve
.
1A-64

Blower
and
Evaporator Assembly
1A-64

Air Distributor Assembly
and
Outlet Ducts ...... 1A-64

Comfortron Automatic Control Components
1A-66

Collision Procedure lA-70

Four-Season Heater Components
1A-73

Comfortron Heater Components
. . . 1A-75

Compressor
1A-76

Wiring Diagrams
1A-78

Special Tools
.
1A-84

GENERAL DESCRIPTION

Four
air
conditioning systems
are
covered
in
this

section. They are:

1.
The
Four-Season System (Chevrolet, Chevelle,

Camaro and Corvette).

2.
The Comfortron System (Chevrolet).

3.
The All Weather System (Chevy n).

4.
The Universal System (Chevrolet, Chevelle, Chevy
n,

Camaro)

Underhood components (that
is, the
compressor,
con-

denser
and
receiver-dehydrator)
are
much
the
same
in

type,
location
and
method
of
attachment
on all of
the

above systems. The six-cylinder reciprocating compres-

sor
is
bracket-mounted
to the
engine
and
belt driven

from
the
crankshaft pulley.
The
condenser
is
mounted

ahead
of the
engine cooling radiator
and the
receiver-

dehydrator
is
mounted
in
the refrigerant line downstream

of
the
condenser.
All
cooling system components
are

connected by means
of
flexible refrigerant lines.

Evaporator size
and
location differ from system
to

system
as do
methods
of
temperature control
and air

supply
and
distribution.

FOUR-SEASON SYSTEM

The Four-Season system used
in the
Chevrolet,

Chevelle, Camaro,
and
Corvette vehicles
may be
iden-

tified
by the
fact that
it
uses
an
evaporator pressure

control known
as the POA
(Pressure Operated Absolute)

suction throttling valve.
Both
the
heating
and
cooling functions
are
performed

by this system.
Air
entering
the
vehicle must pass

through
the
cooling unit (evaporator)
and
through
(or

around)
the
heating unit,
in
that order, and the system
is

thus referred to
as a
''reheat" system.

The evaporator provides maximum cooling
of the air

passing through
the
core when
the air
conditioning sys-

tem
is
calling
for
cooling.
The
control valve acts in the

system only
to
control
the
evaporator pressure
so
that

minimum possible temperature
is
achieved without core

freeze-up.
The
valve
is
preset,
has no
manual con-

trol,
is
automatically altitude compensated,
and non-

repairable.

The heater core will be hot
at
all times since no water

valve
is
present
in
the system.

System operation
is as
follows (See Figure 24 and 25):

Air, either outside
air or
recirculated
air
enters
the

system
and is
forced through
the
system by the blower.

As
the air
passes through
the
evaporator core,
it

receives maximum cooling
if
the
air
conditioning controls

are calling
for
cooling. After leaving
the
evaporator,

the
air
enters
the
Heater
and Air
Conditioner Selector

Duct Assembly where,
by
means
of
manually operated

diverter doors,
it is
caused
to
pass through
or to
bypass

the heater core
in the
proportions necessary
to
provide

the desired outlet temperature. Conditioned airflow then

enters
the
vehicle through either
the
floor distributor

duct
or the
dash outlets. Remember that the heater core

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-30

Leak Detector

Tool J-6084 (fig. 43) is a propane gas-burning torch

which is used to locate a leak in any part of the system.

Refrigerant gas drawn into the sampling tube attached to

the torch will cause the torch flame to change color in

proportion to the size of the leak. Propane gas fuel

cylinders used with the torch are readily available

commercially throughout the country.

CAUTION: Do not use lighted detector in any

place where combustible or explosive gases,

dusts or vapors may be present;

Operating Detector

1.
Open control valve only until a low hiss of gas is

heard, then light gas at opening in chimney.

2.
Adjust flame until desired volume is obtained. This

is most satisfactory when blue flame is approxi-

mately 3/8" above reactor plate. The reaction plate

will quickly heat to a cherry red.

3.
Explore for leaks by moving the end of the sampling

hose around possible leak points in the system. Do

not pinch or kink hose.

NOTE: Since R-12 is heavier than air, it is

good practice to place open end of sampling tube

immediately below point being tested, partic-

ularly in cases of small leaks.

CAUTION: Do not breathe the fumes that are

produced by the burning of R-12 gas in the de-

tector flame, since such fumes can be toxic in

large concentrations of R?»12.

4.
Watch for color changes. The color of the flame

which passes through the reaction plate will change

to yellow when sampling hose draws in very small

CHIMNEY

REACTION PLATE

BURNER HEAD

Fig.
43—Leak Detector
leaks of R-12. Large leaks will be indicated by a

change in color to a vivid purplish-blue. When the

sampling hose passes the leak, the flame will clear

to an almost colorless pale-blue again. If the flame

remains yellow when unit is removed from leak,

insufficient air is being drawn in or the reaction

plate is dirty.

NOTE: A refrigerant leak in the high pressure

side of the system may be more easily detected

when, if possible, the system is in operation. A

leak on the low pressure side may be most

easily detected after the engine has been shut

off for several minutes to allow system pres-

sures to equalize. This particularly applies to

the front seal.

VACUUM PUMP

A vacuum pump should be used for evacuating air and

moisture from the air conditioning system.

Vacuum pump, Tool J-5428, (fig.. 44) is available for

this purpose. It is used as a component part of the

Charging Station J-8393, described previously. The fol-

lowing precautions should be observed relative to tbe

operation and maintenance of this pump.

' • Make sure dust cap on discharge outlet of vacuum

pump is removed before operating.

• Keep all openings capped when not in use to avoid

moisture being drawn into the system.

• Oil should be changed after every 250 hours of nor-

mal operation.

To change oil, simply unscrew hex nut located on

back side of pump, tilt backward and drain out oil

(fig. 44). Recharge with 8 ounces of vacuum pump

oil.
If you desire to flush out the pump, use this

same type clean oil. Do not use solvent.

NOTE: Improper lubrication will shorten the

life of pump.

• If this pump is subjected to extreme or prolonged

cold, allow it to remain indoors until oil has reached

approximate room temperature. Failure to warm oil

will result in a blown fuse.

• A five ampere time delay cartridge fuse has been

installed in the common line to protect the windings

of the compressor. The fuse will blow if an ex-

cessive load is placed on the pump. In the event the

fuse is blown, replace with a five ampere time delay

fuse - do not use a substitute fuse as it will result in

damage to the starting windings.

• If the pump is being utilized to evacuate a burnt-out

system, a filter must be connected to the intake

fitting to prevent any sludge from contaminating the

working parts, which will result in malfunction of the

pump.

• Do not use the vacuum pump as an air compressor.

AVAILABILITY OF REFRIGERANT-12

Refrigerant-12 is available through Parts Stock in 25

lb.
drums and in 15 oz. disposable cans. Valves are

available for
the"
disposable cans, which may be used as

individual cans or as a group of up to four cans (fig. 45).

Tool J-6272 is used with one through four cans. The

use of the four-can fixture makes it possible to charge

the system with a known quantity of refrigerant without

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-37

VACUUM SYSTEM COMPONENT FUNCTION

Component

Air Door Diaphragm

Power Servo

Vacuum Relay Valve

Mode Door Diaphragm

Defroster Diaphragm

Transducer

Thermo Vacuum Valve
Vacuum Applied

Air Door Open to Outside Air

(Closed to Car Body)

Maximum Heat

Vacuum Applied to One Port Opens a Passage

Through the Valve to Allow Transducer Vacuum

to be Supplied to the Power Servo

Vacuum to Linkage Side

Air Flow Out Heater

Ducts

Full Airflow Out Heater

Outlet
Vacuum to Covered Side

Airflow Out of Upper

Outlets

Full Airflow Out Defroster

Outlets (Full De-ice)
No Vacuum Applied

Air Door Open to

Re circulated Air

(Open to Car Body)

Maximum Cooling

No Vacuum Applied Closes

Vacuum Supply to Power

Servo

Airflow Out of Upper and

Lower Outlets Door Open

1"
from 100% Lower Out-

let Position

Airflow Divided 1/3 Out

Defroster Outlets 2/3

Out Heater Outlets

Supplies Modulated Vacuum to Power Servo

Zero Voltage Applied to Transducer

Results in Maximum Vacuum Supply
10 Volts Applied to Transducer

Results in No Vacuum Supply

(Coolant Hot) Passes Vacuum When System is Calling For Outside Air

MAINTENANCE AND ADJUSTMENTS

EVAPORATOR CONTROL VALVE (POA)

(Chevrolet, Chevelle, Comoro, and Corvette

Four Season) (Chevrolet Comfortron)

The only check for proper POA valve operation is to

check the suction pressure at the valve as during a

performance test. The POA valve is an absolute valve

and will provide different gauge readings based on the

altitude where the readings are being taken. Correct

gauge reading at sea level is 29.5 psig. Gauge readings

will be one-half psi higher for each additional 1000 feet

of elevation. The following table lists gauge readings at

different altitudes. If a valve gives improper gauge

readings, it must be replaced since it is not repairable

or adjustable.

29.5

30.0

30.5

31.0

31.5

32.0

32.5

33.0

33.5

34.0

34.5
psig.

psig.

psig.

psig.

psig.

psig.

psig.

psig.

psig.

psig.

psig.
— Sea 1

— 1000

— 2000

— 3000

— 4000

— 5000

— 6000

— 7000

— 8000

— 9000
Level

ft.

ft.

ft.

ft.

ft.

ft.

ft.

ft.

ft.

— 10000 ft.
THERMOSTATIC SWITCH

(Universal and Chevy II All-Weather System)

Thermostatic switches used in Universal and All-

Weather systems differ only in the capillary tube sensing

unit.

The Chevy n All-Weather System thermostatic switch

has an air sensing capillary which is coiled and attached

to the front of the evaporator core with plastic plugs.

This type of unit is controlled by the temperature of the

air leaving the evaporator.

Universal systems make use of a thermostatic switch

with a fin sensing capillary or a self-supporting air sens-

ing capillary. This capillary controls the switch by

sensing the temperature of the metal fins or the air

leaving the fins.

Checking for Proper Operation

1.
Install the gauge set and set up the vehicle as

described under Performance Test.

2.
Movement of the temperature control knob should

result in a definite change in suction pressure and

cycling of the compressor clutch.

• If compressor continues to operate regardless of

the knob adjustment, it indicates that the points

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
IB

CORVETTE BODY

INDEX

Page

General Description . . * • •.
•
^"i1

Maintenance and Replacements 1B-1

Front End 1B-1

Adjustments IBri

Hood 1B-1

Hood Catch 1B-2

Hood Assembly . 1B-2

Front Emblems 1B-2

Vent Grilles 1B-2

Instrument Panel Tray . 1B-2

Cowl Area Trim
....................
1B-4

Rear View Mirror 1B-4

Outside 1B-4

Inside . 1B-4

Sun Visor . 1B-4

Cowl Ventilator Assembly 1B-4

Windshield ; 1B-5

Doors 1B-7

Adjustments 1B-7

Door Lock Striker 1B-7

Door Window and Vent 1B-7

Door Hinges 1B-7

Trim Panel and Inside Handles IB-11

Weatherstrip 1B-11

Door Ventilator Assembly 1B-12

19437 Model 1B-12

19467 Model 1B-13

Window Glass 1B-13

Glass Run Channel—Upper 1B-14

Window Outer Seal Assembly 1B-14

Window Inner Seal Assembly 1B-14

Glass Run Channel—Rear 1B-15

Window Regulator—Manual 1B-15

Window Regulator—Power 1B-15

Door Lock and Remote Controls 1B-16

Outer Handle . 1B-16

Lock Cylinder 1B-17

Hinges—Door Assembly . 1B-17

Rear Quarter .. . 1B-19

Door Sill and Molding . . 1B-19

Rear End . . r 1B-19

Folding Top Compartment Lid 1B-19

Adjustments . . 1B-19

1B-19
Page

Lock 1B-19

Control 1B-19

Rear Window—19437 Model 1B-21

Gas Tank Door and Rear Trim Plate.,. . . . . . . . 1B-23

Rear Filler Panel 1B-23

Spare Tire Mount 1B-23

Rugs and Interior Trim 1B-25

Cleaning Soft Trim 1B-25

Carpets and Covers—All Models 1B-26

Rear Body Trim , . 1B-26

Soft Covers 1B-26

Rigid Plastic Trim 1B-26

Garnish Moldings Plus-Headliner-19437 Model . . 1B-27

Seats 1B-27

Body Mounting 1B-27

Body Repairs . 1B-27

General Instructions . . . 1B-27

Repair Panels. 1B-28

Precautions 1B-29

Plastic Solder Kit 1B-29

Resin Kit 1B-30

Specific Repairs 1B-32

Scratched Panels-Spot Refinishing 1B-32

Dents in Panels-Surface Cracks !B-33

Cracked Panels . . 1B-35

Fractures 1B-37

Panel Replacement 1B-39

Hard Top . . 1B-41

Care and Storage 1B-41

Rear Window 1B-41

Garnish Moldings and Latches 1B-42

Headlining 1B-43

Weatherstrips and Drip Molding 1B-43

Vinyl Covering . 1B-43

Folding Top 1B-46

Care of Folding Top 1B-46

Care of Rear Window 1B-46

Adjustments 1B-48

Top Assembly, Removal and Installation 1B-49

Top Trim and Rear Window Assembly 1B-50

Frame and Linkage 1B-52

Weatherstrip 1B-52

Adding Hardtop 1B-52

Special Tools 1B-53

GENERAL DESCRIPTION

.
A
structural network
of
steel forms the backbone
of
the

Corvette body. When combined with
the
fiber-glass
re-

inforced plastic body panels,
the
steel-plastic marriage

results
in a
body with increased torsional rigidity
and

greater beaming strength.
Convertible models continue with two roof styles:
the

folding
top
and the removable hardtop. In operation, both

tops function similar to those
of
previous models. Either

top
is
standard and both
are
optional
as
determined by

the top selected
as
base equipment.

MAINTENANCE
&
REPLACEMENTS

FRONT
END

ADJUSTMENTS

(Refer to Figure
2)

Adjustments should
be
made
in
order
-
hood position

first, then catch adjustments.
Hood

The position
of the
hood
in
relation
to
the hood body

opening and the fender surfaces
is
controlled by the posi-

tion
of the
hinges and position
and
adjustment
of
catch

and bumpers.

The fore
and aft
position
of the
hood may be adjusted

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
3

FRONT SUSPENSION

INDEX

Page

General Description
. . . . 3-1

Maintenance and Adjustments
3-3

Front Wheel Bearing Adjustment
3-3

Front End Alignment
3-5 .

Alignment Preliminary Steps ............
3-5

Caster
and
Camber Adjustments
. . 3-5

Chevelle, Caxnaro
and
Corvette
3-5

Chevrolet and Chevy
II 3-6

Steering Axis Inclination
3-6

Toe-in Adjustment
3-6

Cornering Wheel Relationship
3-6

Riding Heigit
and
Coil Spring Sag
3-7

Repair Procedures
3-8

Front Brake Drum (Chevrolet, Camaro, Chevelle,

Chevy E)
. . 3-8

Removal
3-8

Installation
3-8

Front Wheel Hub
3-8

Replacement
. . . . . 3-8

Replacement
of
Hub Wheel Bolts
3-8

Front Wheel Bearings
. . 3-8

Removal
3-8

Inspection
3-9

Repairs
. . 3-9

Replacement
of
Bearing Cups
3-9

Installation
3-9

Steering Knuckle
. . . 3-9

Removal
3-9

Installation
3-9

Shock Absorber
3-10

Chevrolet, Chevelle, Camaro
and

Corvette
3-10

Removal
, . 3-10

Installation
3-10

Chevy
It 3-11

Removal
3-11

Installation
3-11

Stabilizer
Bar 3-11

Removal
3-11

Installation
3-11

Strut Rod
3-11

Chevrolet and Chevy
II 3-11

Removal
3-11

Installation
3-12

Front Coil Springs
3-12

Chevrolet
3-12

Removal
3-12

Installation
3-13

Chevelle
and
Camaro
3-13

Removal
3-13

Installation
3-14

Chevy H
3-14

Removal
3-14

Spring Seat Disassembly and Assembly
3-15

Installation
3-15

Corvette
3-15

Lower Control Arm Spherical Joint
.' 3-16

Chevrolet, Chevelle, Camaro and

Corvette
3-16

Inspection
. 3-16

Chevrolet and Corvette
3-16

Removal
3-16

Installation
3-16
Page

Chevelle
and
Camaro
3-17

Removal
3-17

Installation
. . . . 3-17

Chevy
II 3-17

Inspection
. 3-17

Removal
3-17

Installation
3-17

Lube Fittings
3-18

Lower Control Arm
. . . . 3-18

Chevrolet
. 3-18

Removal
3-18

Installation
3-18

Chevelle and Camaro
3-18

Removal
3-18

Installation
3-18

Chevy H
3-18

Removal
3-18

Installation
3-19

Corvette
3-19

Removal
3-19

mstallation
3-19

Lower Control Arm Bushings
3-20

Chevrolet
3-20

Removal
3-20

Installation
3-20

Chevelle and Camaro
. 3-20

Removal
3-20

Installation
3-20

Chevy H
3-21

Removal
* 3-21

InstaEation
3-21

Cross Shaft and/or Bushings
. 3-21

Corvette
3-21

Removal
3-21

Installation
3-21

Upper Control Arm Spherical Joint
3-21

Chevrolet, Chevelle, Camaro and Corvette
..... 3-21

Inspection.
3-21

Replacement
3-21

Chevy
II 3-21

Inspection
3-21

Replacement
3-21

Lube Fittings
3-22

Upper Control Arm
3-22

Chevrolet, Chevelle, Camaro
and
Corvette
3-22

Removal
3-22

Installation
3-22

Chevy H
3-22

Removal
3-22

Installation
3-23

Upper Control Arm Cross Shaft

and/or Bushings
3-23

Chevrolet, Camaro and Chevelle
3-23

Removal
. 3-23

Installation
3-23

Chevy H
3-24

Removal
3-24

Installation
. . . 3-25

Corvette
3-25

Removal
3-25

Installation
3-25

Special Tools
3-26

Specifications
...'..'
At rear of Book

GENERAL DESCRIPTION

The 1967 Chevrolet, Chevelle, Camaro, Chevy n and

Corvette front suspension systems are basically similar,

being of the
S.L.A.
(short-long arm) type with independent

coil springs. In the Chevrolet, Chevelle, Camaro and

Corvette the springs ride on the lower control arms; in
the Chevy II the springs ride on the upper control arms.

Spherical joints connect the upper and lower arms to the

steering knuckle. Tapered roller wheel bearings are

used.

Camber angle is adjusted, on the Chevrolet and Chevy n

CHEVROLET CHASSIS SERVICE MANIM

FRONT SUSPENSION 3-3

by means of a lower control arm inner pivot cam; on the

Chevelle, Camaro and Corvette by means of upper control

arm inner support shaft shims.

Caster angle is adjusted, on the Chevrolet and Chevy n

by means of a strut rod which runs from the lower con-

trol arm forward to a frame brace; on the Chevelle,
Camaro and Corvette by means of upper control arm

inner support shaft shims.

A stabilizer bar is used on all Chevelle and Corvette

models. Chevrolet Impalas, station wagons and V-8

engine equipped models are fitted with the stabilizer bar.

UPPER CONTROL ARM

STABILIZER

SPRING
LOWER CONTROL ARM

STEERING KNUCKLE

Fig.
3 - Front Suspension - Corvette

MAINTENANCE AND ADJUSTMENTS

Maintenance intervals recommended for lubrication of

front suspension components have been fully covered in

Section 0 of this manual. Only actual adjustment proce-

dures will be covered here.

NOTE:
Unless otherwise indicated all proce-

dures will apply to all five vehicles covered in

this manual.

FRONT WHEEL BEARING ADJUSTMENT

Proper front wheel bearing adjustment has a definite

bearing on the safe operation of a vehicle. Improperly

adjusted front wheel bearings will result in a lack of

steering stability causing wheel wander, shimmy and ex-

cessive tire wear. Very accurate adjustment is possible

because the spindles are drilled both vertically and hori-

zontally and the adjusting nuts are slotted in all six sides.

NOTE:
Wheel bearings should not
be.
repacked

or adjusted as a part of "New Car Conditioning".
1.
With wheel raised, remove hub cap and dust cap and

then remove the cotter pin from the end of the

spindle.

2.
While rotating wheel, tighten spindle nut to 12 lbs. ft

torque.

3.
Back off adjusting nut one flat and insert cotter pin.

If slot and pin hole do not line up, back off the adjust-

ing nut an additional 1/2 flat or less as required to

insert cotter pin.

4.
Spin the wheel to check that it rolls freely and then

lock the cotter pin by spreading the end and bending

it around.

NOTE:
Bearings should have zero preload and

.001"
to .008" end movement when properly ad-

justed on Chevrolet, Chevelle, Camaro and Cor-

vette; .000" to .004" on Chevy H.

5.
Install dust cap, hub cap or wheel disc and lower

wheel.

6. Perform the same operation on each front wheel.

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-10

CHEVROLET, CHEVELLE, CAMARO AND CORVETTE (TYPICAL)
CHEVY H

Fig.
14- Shock Absorber

NOTE:
If necessary, tighten one more notch to

insert cotter pins.

3.
Place brake backing plate and wheel cylinder in posi*-

tion on steering knuckle and insert anchor pin.

4.
Place steering arm in position on back of steering

knuckle and insert two bolts through backing plate,

steering knuckle and steering arm. Install locknuts

and tighten. (See Specifications.)

5. Torque brake anchor pin (See Specifications).

6. Install brake shoes, except Corvette. (See Section 5.)

7. Install wheel hub, brake drum (or, on Corvette--

brake caliper and disc and hub assembly), wheel and

tire assembly over spindle.

8. Insert outer wheel bearing race and roller assembly,

washer and nut. Adjust front wheel bearing as shown

under Maintenance and Adjustments in this section.

Install new cotter pin, dust cap and hub cap.

9. Lower vehicle, recheck and readjust wheel alignment

where necessary.

SHOCK ABSORBER

Chevrolet, Chevelle, Comoro and Corvette (Fig. 14)

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.

2.
Remove the two bolts retaining the lower shock ab-

sorber pivot to the lower control arm and pull the

shock absorber assembly out from the bottom.

Installation

1.
With the retainer and rubber grommet in place over

the upper stem, install the shock abosrber (fully ex-
tended) up through the lower control arm and spring

so that the upper stem passes through the mounting

hole in the upper support arm.

2.
Install the rubber grommet, retainer' and attaching

nut over the shock absorber upper stem.

3.
With an open end wrench, hold the upper stem

from turning and tighten the retaining nut. (See

Specifications.)

4.
Install the two bolts attaching the shock abosrber

lower pivot to the lower control arm and tighten.

(See Specifications.)

Fig.
15 - Upper Control Arm Support Installed - Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
4

REAR SUSPENSION
AND
DRIVE LINE

CONTENTS
OF
THIS SECTION

Page

Rear Suspension
4-1

Drive Line.
. 4-26

Rear Axle ......
4-26
Propeller Shaft
and
Universal Joints

Special Tools
4-37

4-43

REAR SUSPENSION

INDEX

General Description
4-1

Chevrolet
4-1

Chevelle
4-1

Chevy
n and
Camaro
. . . . . 4-2

Corvette
. . . . . . 4-3

Maintenance
and
Adjustments ...............
4-4

Riding Height Check (Chevrolet, Camaro,

Chevelle
and
Chevy
II) 4-5

Wheel Alignment (Corvette)
4-5

Wheel Bearing Adjustment (Corvette)
4-6

Component Parts Replacement (Chevrolet, Camaro,

Chevelle
and
Chevy
JJ) 4-7

Coil Spring
4-7

Chevrolet
4-7

Removal
4-7

Installation
4-7

Chevelle
4-8

Removal
4-8

4-8

Installation
.

Leaf Spring, Spring Seat Pads, Spring
Eye

Bushings
4-9

Chevy
H 4-9

Removal
4-9

Installation
4-9

Camaro
4-10

Removal
4-10

Installation
4-11

Shock Absorber
4-11

Chevrolet
and
Chevelle
. 4-11

Removal
4-11

Installation
. . 4-12

Chevy
II 4-12

Removal
4-12

Installation
4-rl2

Camaro
4-12

Removal
. 4-12

Installation
4-12

Control
Arm . . 4-12

Chevrolet Upper
4-12

Removal
. 4-12
Page

Bushing Replacement
. 4-13

Installation
4-14

Chevrolet Lower
4-14

Removal
4-14

Bushing Replacement
4-14

Installation
. 4-15

Chevelle Upper
and
Lower.
. 4-15

Removal
4-15

Bushing Replacement
4-15

Installation
4-17

Rear Suspension
Tie Rod
(Chevrolet)
. . .
......
. . . 4-17

Removal
4-17

Bushing Replacement
4-17

Installation
4-17

Component Parts Replacement (Corvette)
. . 4-17

Wheel Spindle
and
Support
4-17

Removal
4-17

Repairs
', . 4-17

Installation
4-18

Differential Carrier Support Bracket Replacement.
. 4-20

Shock Absorber
4-20

Removal
4-20

Installation
* .... 4-20

Strut
Rod and
Bracket
4-20

Removal
4-20

Repairs
4-21

Installation
4-21

Spring
4-21

Removal
4-21

Repairs
4-22

Installation
4-22

Torque Control
Arm 4-23

Removal
4-23

Repairs
. 4-23

Installation
4-24

Suspension Crossmember
4-24

Removal
4-24

Repairs—Isolation Mount
4-25

Installation
4-25

Stabilizer Shaft Replacement
4-25

GENERAL DESCRIPTION

CHEVROLET

The link type rear suspension (fig. 1) has two lower

control arms which maintain proper axle to frame re-

lationship and also take the acceleration, drive and

braking forces. A single upper control arm on light-

duty models (or two upper control arms on heavy-duty

models and all station wagons) limits axle rotation when

drive, acceleration or braking forces are applied. Lateral

movement of the axle is restricted by the axle-to-frame

tie rod. Two full coil springs and two direct, double
acting shock absorbers are provided for additional ride

control.

CHEVELLE

The rear suspension (fig. 2) is of the four-link design

utilizing axle mounted, full coil springs and direct,

double-acting shock absorbers.

Two rubber-bushed lower control arms, stretching

slightly outboard from axle-mounted brackets to frame

side member mounted brackets, maintain fore and aft

CHEVROLET CHASSIS SERVICE MANUAL