2023 HYUNDAI IONIQ 6 stop start
[x] Cancel search: stop startPage 246 of 582
Convenience Features
5-68
B5015603
Parking light ( )
The parking light, license plate light and
instrument panel lamp are turned ON.
B5015604
Headlight ( )
The headlight, parking light, license plate
light and instrument panel lamp are
turned ON.
Information The Start/Stop button must be in the ON
position to turn on the headlight.
High beam operation
B5015702
To turn on the high beam headlight, push
the lever away from you. The lever will
return to its original position.
The high beam indicator will light when
the headlight high beams are switched
on.
To turn off the high beam headlight, pull
the lever towards you. The low beams will
turn on.
B5015701
To flash the high beam headlight, pull the
lever towards you, then release the lever.
The high beams will remain ON as long as
you hold the lever towards you.
Hyundai_CE_en_US.book Page 68
Page 247 of 582
5
5-69
Turn signals and lane change signals
B5015801
To signal a turn, push down on the lever
for a left turn or up for a right turn in
position (A).
If an indicator stays on and does not flash
or if it flashes abnormally, one of the turn
signal bulbs may be burned out and will
require replacement.
One touch turn signal
To use One Touch Turn Signal push the
turn signal lever up or down to position
(B) and then release it.
The lane change signals will blink 3, 5 or 7
times.
You can enable the One Touch Turn
Signal function or choose the number of
blinking by selecting Setup > Vehicle >
Lights > One Touch Turn Signal (or
One-touch indicator ) > 3 flashes /5
flashes /7 flashes /Off in the infotainment
system.
Information The infotainment system may change after
software updates. For more information, refer
to the user's manual provided in the
infotainment system and the quick reference
guide.
Battery saver function
To prevent the battery from being
discharging, the system automatically
turns off the parking lights when the
driver turns the vehicle off and opens the
driver’s door.
To keep the lights on when the vehicle is
turned off:
1. Open the driver’s door.
2. Turn the parking lights OFF and ON again using the headlight switch.
Headlight delay function
If the Start/Stop button is in the ACC
position or the OFF position with the
headlights ON, the headlights (and/or
Parking lights) remain on for about 5
minutes. However, if the driver’s door is
opened and closed, the headlights are
turned off after 15 seconds. Also, with the
vehicle off if the driver’s door is opened
and closed, the headlights (and/or
Parking lights) are turned off after 15
seconds.
The headlights (and/or Parking lights) can
be turned off by pressing the lock button
on the smart key twice or turning the
headlight switch to the OFF or AUTO
position.
You can enable the headlight delay
function by selecting Setup > Vehicle >
Lights > Headlight Delay (or Headlight
time-out) in the infotainment system.
Information The infotainment system may change after
software updates. For more information, refer
to the user's manual provided in the
infotainment system and the quick reference
guide.
Hyundai_CE_en_US.book Page 69
Page 249 of 582
5
5-71
Interior Lights
WARNING Do not use the interior lights when driving
in the dark. The interior lights may
obscure your view and cause an accident.
NOTICE ' R Q R W X V H W K H L Q W H U L R U O L J K W V I R U H [ W H Q G H G
S H U L R G V Z K H Q W K H Y H K L F O H L V W X U Q H G R I I R U
W K H E D W W H U \ Z L O O G L V F K D U J H
Interior Light AUTO cut
The interior lights will automatically go off
about 20 minutes after the vehicle is
turned off and the doors are closed. If a
door is opened, the light will go off 25
minutes after the vehicle is turned off. If
the doors are locked by the smart key and
the vehicle enters the armed stage of the
theft alarm system, the lights will go off
five seconds later.
Front lamps
B5017701
Front map lamp ( ):
Touch either icons to turn the map lamp
on or off. This light produces a spot beam
for convenient use as a map lamp at night or as a personal light for the driver and the
front passenger.
Door lamp ( ):
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lights come on for
about 30 seconds as long as any door is
not opened. The front and rear room
lamps go out gradually after about 30
seconds when the door is closed.
However, if the Start/Stop button is in the
ON position or all doors are locked, the
front and rear lights will turn off. If a door
is opened with the Start/Stop button in
the ACC position or the OFF position, the
front and rear lights will stay on for about
10 minutes.
Room lamp ( ):
Press the button to turn ON the room
lamp for the front/rear seats.
if equipped
Mood lamp ( ):
Press the button to turn On the mood
lamp. Press again to turn the lamp off.
Rear lamps
Room lamp
B5017801
Press the button to turn the lamp on or
off.
Hyundai_CE_en_US.book Page 71
Page 252 of 582
Convenience Features
5-74
if equipped
High Beam Assist (HBA)
B5016701
High Beam Assist automatically controls
the headlights between high beam and
low beam depending on the detected
ambient light, such as an oncoming
vehicle or leading vehicle.
Detecting sensor
B5016702(1) front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the illustration above for the
detailed location of the detecting sensor.
NOTICE [ $ O Z D \ V N H H S W K H I U R Q W Y L H Z F D P H U D L Q J R R G F R Q G L W L R Q W R P D L Q W D L Q R S W L P D O
S H U I R U P D Q F H R I + L J K % H D P $ V V L V W
[ ) R U P R U H L Q I R U P D W L R Q R Q W K H S U H F D X W L R Q V R I W K H I U R Q W Y L H Z F D P H U D U H I H U W R W K H U ) R U Z D U G
& R O O L V L R Q $ Y R L G D Q F H $ V V L V W ) & $ \fV
V H F W L R Q L Q F K D S W H U
High Beam Assist Settings
Setting features
ONE1051248L
With the Start/Stop button in the ON
position, select Setup > Vehicle > High
Beam Assist from the Settings menu to
turn on High Beam Assist and deselect to
turn off the function.
WARNING For your safety, change the Settings after
parking the vehicle at a safe location.
High Beam Assist Operation
Display and control
• After selecting 'High Beam Assist' in
the Settings menu, High Beam Assist
will operate by following the procedure
below.
- Place the headlight switch in the AUTO position and push the
headlight lever towards the
instrument cluster. The High Beam
Assist ( ) indicator light will
illuminate on the instrument cluster
1
Hyundai_CE_en_US.book Page 74
Page 255 of 582
5
5-77
Wipers and Washers
B5019601
A. Wiper speed control
• MIST - Single wipe
• OFF - Off
• INT - Intermittent wipeAUTO* - Auto control wipe
• LO - Low wiper speed
• HI - High wiper speed
B. Intermittent wipe time
adjustment/Auto control wipe time
adjustment*
C. Wash with brief wipes
*: if equipped
Front Windshield Wipers
Operates as follows when the Start/Stop
button is in the ON position.
MIST:
For a single wiping cycle, push the lever
upward (or downward) and release. The
wipers will operate continuously if the
lever is held in this position.
OFF:
Wiper is not in operation.
INT:
Wiper operates intermittently at the same
wiping intervals. To vary the speed
setting, turn the speed control knob (B).
AUTO:
The rain sensor located on the upper end
of the windshield glass senses the amount of rainfall and controls the wiping
cycle for the proper interval. The more it
rains, the faster the wiper operates. When
the rain stops, the wiper stops. To vary the
speed setting, turn the speed control
knob.
LO:
The wiper runs at a lower speed.
HI:
The wiper runs at a higher speed.
Information If there is heavy accumulation of snow or ice
on the windshield, defrost the windshield for
about 10 minutes, or until the snow and/or ice
is removed before using the windshield wipers
to ensure proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
B5019603
The rain sensor located on the upper end
of the windshield glass senses the
amount of rainfall and controls the wiping
cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
MIST
OFFOFF
INT/AUTO*INT/AUTO*
LO
HI
Hyundai_CE_en_US.book Page 77
Page 256 of 582
Convenience Features
5-78
If the wiper switch is set in AUTO mode
when the Start/Stop button is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WARNING To avoid personal injury from the
windshield wipers, when the vehicle is
running and the windshield wiper switch
is placed in the AUTO mode:
• Do not touch the upper end of the windshield glass facing the rain sensor.
• Do not wipe the upper end of the windshield glass with a damp or wet
cloth.
• Do not put pressure on the windshield glass.
NOTICE [ : K H Q Z D V K L Q J W K H Y H K L F O H V H W W K H Z L S H U V Z L W F K L Q W K H 2 ) ) S R V L W L R Q W R V W R S
W K H D X W R Z L S H U R S H U D W L R Q 7 K H Z L S H U
P D \ R S H U D W H D Q G E H G D P D J H G L I W K H
V Z L W F K L V V H W L Q W K H $ 8 7 2 P R G H Z K L O H
Z D V K L Q J W K H Y H K L F O H
[ ' R Q R W U H P R Y H W K H V H Q V R U F R Y H U O R F D W H G R Q W K H X S S H U H Q G R I W K H
S D V V H Q J H U V L G H Z L Q G V K L H O G J O D V V
' D P D J H W R V \ V W H P F R P S R Q H Q W V F R X O G
R F F X U D Q G P D \ Q R W E H F R Y H U H G E \ \ R X U
Y H K L F O H Z D U U D Q W \
[ % H F D X V H R I X V L Q J D S K R W R V H Q V R U W H P S R U D U \ P D O I X Q F W L R Q F R X O G R F F X U
D F F R U G L Q J W R V X G G H Q D P E L H Q W O L J K W
F K D Q J H P D G H E \ V W R Q H D Q G G X V W Z K L O H
G U L Y L Q J
Front Windshield Washers
B5019701
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield and to run the wipers 1-3
cycles. The spray and wiper operation will
continue until you release the lever. If the
washer does not work, you may need to
add washer fluid to the washer fluid
reservoir.
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending on
the outside temperature. If you select
fresh mode while the function is
operating, the function will resume after a
certain amount of time. It may not work in
some conditions such as cold weather or
vehicle off.
For more information, refer to the
“Climate Control Additional Features”
section in this chapter.
WARNING When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent the
washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
Hyundai_CE_en_US.book Page 78
Page 273 of 582
5
5-95
3. Touch the defroster icon ( ).
4. When Defogging logic is enabled, Fresh mode is selected and air conditioning is
selected according to outside
temperature.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, touch the
icon once to enable Fresh mode
(indicator light OFF).
If the position is selected, lower fan
speed is adjusted to a higher fan speed.
Defogging Logic
To reduce the probability of fogging up
the inside of the windshield, the air intake
or air conditioning are controlled
automatically according to certain
conditions such as positions. To cancel
or reset the defogging logic, do the
following.
1. Press the Start/Stop button to the ON position.
2. Touch the defroster icon ( ) or ( ).
3. While touching the A/C icon, touch the air intake control icon at least 5 times
within 3 seconds.
The air intake control indicator will blink 3
times to indicate that the defogging logic
has been disabled. Repeat the steps again
to re-enable the defogging logic.
The air intake control indicator will blink 6
times to indicate that the defogging logic
has been enabled.
If the battery has been discharged or
disconnected, it resets to the defog logic
status.
Rear Window Defroster
NOTICE To prevent damage to the rear window
defroster conducting elements bonded to
the inside surface of the rear window,
never use sharp instruments or window cleaners containing abrasives to clean the
window.
B5020801
The defroster heats the window to
remove frost, fog and thin ice from the
interior and exterior of the rear window,
while the vehicle is running.
• To activate the rear window defroster,
touch the rear window icon located in
the center control panel. The indicator
on the rear window defroster
illuminates when the defroster is on.
• To turn off the defroster, touch the rear window defroster button again.
Information • If there is heavy accumulation of snow on the rear window, brush it off before
operating the rear defroster.
• The rear window defroster automatically turns off after about 20 minutes or when the
Start/Stop button is in the OFF position.
Side view mirror defroster
If your vehicle is equipped with the
rearview mirror defrosters, they will
operate at the same time you turn on the
rear window defroster.
Hyundai_CE_en_US.book Page 95
Page 274 of 582
Convenience Features
5-96
Climate Control
Additional Features
if equipped
A/C Automatic Drying
A/C Automatic Drying feature dries the
moisture in the air conditioner and
reduces air conditioner odor. The blower
motor automatically operates after 30
minutes the vehicle is turned off.
Turning A/C Automatic Drying On or
off
The A/C Automatic Drying feature can be
turned on and off by selecting Setup >
Vehicle Settings > Climate > Climate
Features > A/C Automatic Drying from
the infotainment system.
Information The infotainment system may change after
software updates. For more information, refer
to the user's manual provided in the
infotainment system and the quick reference
guide.
If the operating condition is satisfied after
setting the feature, the operating
condition is displayed on the
infotainment system and the blower
motor automatically operates.
When the A/C Automatic Drying feature is
activated, the air conditioner sets the fan
speed to the third level, selects Fresh
mode, and directs the air flow to the floor.
Operating conditions
The A/C Automatic Drying feature
operates under the following conditions:
• The vehicle is turned off after operating the air conditioner for a certain period
• The 12 V battery level is sufficient • The outside temperature is above a
certain level
Non-operating conditions
The A/C Automatic Drying feature stops
operating under the following conditions:
• The A/C Automatic Drying feature has operated for 3 minutes
• The Start/Stop button is pressed, or the vehicle is on
• The climate control system is operated remotely
Information • The A/C Automatic Drying feature reduces air conditioner odors but may not remove
all odors.
• The A/C Automatic Drying feature does not operate if the remaining battery level is
insufficient to prevent battery discharge.
Auto Defogging System
B5021201
Auto defogging helps reduce the
possibility of fogging up the inside of the
windshield by automatically sensing the
moisture on inside the windshield.
Information The auto defogging system may not operate
normally, when the outside temperature is
below 14 °F (-10 °C).
Hyundai_CE_en_US.book Page 96