2023 HYUNDAI IONIQ 6 battery
[x] Cancel search: batteryPage 202 of 582
Convenience Features
5-24
Information When the door handle or the keyhole freeze
and do not open, lightly tap or indirectly warm
(for example, hand temperature) the keyhole.
Since the smart key and the mechanical key
are separated, always carry the mechanical
key in case the vehicle battery and the smart
key battery are discharged.
In case of an emergency
B5003103
Doors without an outside key hole can be
locked as follows:
1. Open the door.
2. Insert the key into the emergency door lock hole and turn the key to the lock
position.
3. Close the door securely.
Information If the electrical power to door lock switch is
not operating (for example, discharged
vehicle battery) and the trunk is closed, you
cannot open the trunk until power is restored.
WARNING • Always close and lock the doors while the vehicle is moving. If the doors are
unlocked, the risk of being thrown from
the vehicle in a collision increases. • Do not pull the inner door handle of the
driver’s or passenger’s door while the
vehicle is moving.
WARNING Do not leave the elderly, children, or
animals unattended in your vehicle. An
enclosed vehicle can become extremely
hot and the elderly, unattended children
or animals who cannot escape the vehicle
may be seriously injured or killed.
WARNING Always park your vehicle properly.
Depress the brake pedal, change the gear
to P (Park), apply the parking brake, press
the Start/Stop button to the OFF position,
close all windows, lock all doors, and
always take the keys with you.
WARNING Be careful when opening doors and
watch for vehicles, motorcycles, bicycles,
or pedestrians approaching the vehicle to
prevent serious injury or death.
Information To exit the vehicle if the power door lock does
not function:
• Operate the door unlock feature repeatedly (both electronic and manual) while
simultaneously pulling on the door handle.
• Operate the other door locks and handles.
• Lower the driver’s front window and use the mechanical key to unlock the door from
outside.
Hyundai_CE_en_US.book Page 24
Page 208 of 582
Convenience Features
5-30
Declaration of Conformity
The radio frequency components (ROA
Radar Sensor) complies:
• For USA
OANATEL323
• For Canada
OANATEL324
Integrated Memory
if equipped
System
B5005201
Integrated Memory System for the
driver’s seat is provided to store and recall
the following memory settings with a
simple button operation.
• Driver’s seat position
• Side view mirror position
• Head-up display position
WARNING Never attempt to operate the integrated
memory system while the vehicle is
moving.
Information • If the battery is disconnected, the memory settings will be erased.
• If integrated memory system does not operate normally, have the system
inspected by an authorized HYUNDAI
dealer.
Hyundai_CE_en_US.book Page 30
Page 210 of 582
Convenience Features
5-32
Seat Easy Access
Seat easy access will move the driver’s
seat automatically as follows:
• Exiting the vehicle:The driver’s seat will move as follows
when the Start/Stop button is in the
OFF position with the gear in P (Park)
and the driver’s door open.
- Driver seat: Moves rearward depending on the distance selected
from the Settings menu in the
infotainment system.
However, the driver’s seat may not
move rearward if there is not enough
space between the driver’s seat and the
rear seats.
• Entering the vehicle: The driver’s seat will move as follows
when the Start/Stop button is pressed
to the ACC, ON or START position or
while carrying the smart key, the
driver’s door is closed with the
Start/Stop button in the OFF position.
- Driver seat: Moves back to its original position.
• You can set the 'Seat Easy Access' function from the Settings menu in the
infotainment system. Select:
- Driver seat
Setup > Vehicle > Seat > Seating
Easy Access > Driver Seat Easy
Access > Extended/Normal/Off
Information The infotainment system may change after
software updates. For more information, refer
to the user's manual provided in the
infotainment system and the quick reference
guide.
Steering Wheel
Motor Driven Power Steering
(MDPS)
The system assists you with steering the
vehicle. If the vehicle is turned off or if the
power steering system becomes
inoperative, you may still steer the
vehicle, but it will require increased
steering effort.
If you notice any change in the effort
required to steer during normal vehicle
operation, have the system inspected by
an authorized HYUNDAI dealer.
CAUTION If Motor Driven Power Steering does not
operate normally, the warning light and
the message 'Check motor driven power
steering' will illuminate on the instrument
cluster. You may steer the vehicle, but it
will require increased steering efforts.
Take the vehicle to an authorized
HYUNDAI dealer and have the system
inspected as soon as possible.
Information During normal vehicle operation:
• The steering effort may be high immediately after pressing the Start/Stop
button to the ON position.
This happens as the system performs the
MDPS system diagnostics. When the
diagnostics are completed, the steering
wheel effort will return to its normal
condition.
• When the 12 V battery voltage is low, you might have to put more steering effort.
However, it is a temporary condition so that
it will return to normal condition after
charging the battery.
Hyundai_CE_en_US.book Page 32
Page 215 of 582
5
5-37
Automatic-Dimming Night Vision Safety™
if equipped
(NVS®) Mirror
The NVS® Mirror automatically reduces
glare by monitoring light levels in the
front and the rear of the vehicle. Any
object that obstructs either light sensor
will degrade the automatic dimming
control feature.
For more information regarding NVS®
mirrors and other applications, please
refer to the Gentex website:
www.gentex.com
Your mirror will automatically dim upon
detecting glare from the vehicles
traveling behind you.
The mirror defaults to the ON position
each time the vehicle is started.
Integrated HomeLink® Wireless Control
System
The HomeLink® Wireless Control System
provides a convenient way to replace up
to three hand-held radio-frequency
transmitters used to activate compatible
devices such as gate operators, garage
door openers, entry door locks, security
systems, and home lighting.
NOTICE + R P H / L Q N p R S H U D W H V Z K L O H W K H 6 W D U W 6 W R S
E X W W R Q L V L Q W K H $ & & R U 2 1 S R V L W L R Q I R U
V D I H W \ U H D V R Q V , W L V W R S U H Y H Q W
X Q L Q W H Q W L R Q D O V H F X U L W \ S U R E O H P V I U R P
K D S S H Q L Q J Z K H Q W K H Y H K L F O H L V S D U N H G
R X W V L G H W K H J D U D J H
WARNING Before programming HomeLink® to a
garage door opener or gate operator,
make sure people and objects are out of
the way of the device to prevent potential
harm or damage. Do not use the
HomeLink® with any garage door opener
that lacks the safety stop and reverse features required by U.S. federal safety
standards (this includes any garage door
opener model manufactured before April
1, 1982). A garage door that cannot detect
an object-signaling the door to stop and
reverse-does not meet current U.S.
federal safety standards. Using a garage
door opener without these features
increases the risk of serious injury or
death.
For more information, contact
HomeLink® at www.homelink.com, or call
Home-Link customer support at
1-800-355-3515.
It is also recommended that a new battery
be replaced in the hand-held transmitter
of the device being trained to HomeLink®
for quicker training and accurate
transmission of the radio frequency.
1. Programming HomeLink®
The following steps show how to program
HomeLink. If you have any questions or
are having difficulty programming your
HomeLink buttons, refer to the HomeLink
website or call the HomeLink customer
support toll-free number. Do this, before
going back to the dealer who sold you the
vehicle.
• Visit the HomeLink website at:
www.homelink.com. Then at the top of
the page, choose your vehicle make.
Then watch the You Tube video, and/or
access additional website information.
• If you choose to access the website via your cell phone, scan the QR code.
• Or, call HomeLink customer support at 1-800-355-3515 (Please have the
vehicle make/model AND the opener
device make/model readily available.)
Hyundai_CE_en_US.book Page 37
Page 216 of 582
Convenience Features
5-38
1) Programming Preparation
ONE1051262N
1. When programming a garage door opener, it is advised to park the vehicle
outside of the garage.
2. It is recommended that a new battery be placed in the hand-held transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the
radio-frequency signal.
3. Press the Start/Stop button to the ACC (Accessory) position for programming
of HomeLink.
2) Programming a New HomeLink®
ONE1051263N
1. Press and release the HomeLink button (1), (2) or (3), you would like to program.
The HomeLink indicator light (7) will
flash orange slowly (if not, perform the
steps of “Erasing HomeLink Buttons”
section, and start over).
ONE1051264N
2. Position the garage door opener remote 1-3 in. (2-8 cm) away from the
HomeLink buttons.
3. While the HomeLink indicator light (7) is flashing orange, press and hold the
hand-held remote button. Continue
pressing the hand-held remote button
until the HomeLink indicator light (7)
light changes from orange to green.
You may now release the hand-held
remote button.
4. Wait until your garage door comes to a complete stop, regardless of position,
before proceeding to the next steps.
5. Press and release the HomeLink button you are programming and observe the
indicator light.
• If the indicator light remains solid green, your device should operate
when the HomeLink button is
pressed. At this point, if your device
operates, programming is complete.
• If the indicator light rapidly flashes green, firmly press, hold for two
seconds and release the HomeLink
button up to three times in a row
slowly to complete the programming
process. Do not press the HomeLink
button rapidly. At this point if your
device operates, programming is
complete. If the device does not
operate, continue with step 6.
6. At the garage door opener motor, (security gate motor, etc.) locate the
'Learn', 'Smart', 'Set' or 'Program'
button. This can usually be found where
Hyundai_CE_en_US.book Page 38
Page 230 of 582
Convenience Features
5-52
NOTICE [ ' R Q R W F R Q W L Q X H W R S X V K W K H V X Q U R R I V Z L W F K D I W H U W K H V X Q U R R I L V I X O O \ R S H Q H G
F O R V H G R U W L O W H G ' D P D J H W R W K H V X Q U R R I
P R W R U F R X O G R F F X U
[ & R Q W L Q X R X V R S H U D W L R Q V V X F K D V V O L G H R S H Q F O R V H W L O W R S H Q F O R V H H W F P D \
F D X V H W K H P R W R U R U V X Q U R R I V \ V W H P W R
P D O I X Q F W L R Q
[ 5 H J X O D U O \ U H P R Y H D Q \ D F F X P X O D W H G G X V W R Q W K H V X Q U R R I U D L O
[ ' X V W D F F X P X O D W H G E H W Z H H Q W K H V X Q U R R I D Q G U R R I S D Q H O F D Q P D N H Q R L V H 2 S H Q
W K H V X Q U R R I D Q G U H P R Y H G X V W U H J X O D U O \
X V L Q J D F O H D Q F O R W K
[ ' R Q R W W U \ W R R S H Q W K H V X Q U R R I Z K H Q W K H W H P S H U D W X U H L V E H O R Z I U H H ] L Q J R U Z K H Q
W K H V X Q U R R I L V F R Y H U H G Z L W K V Q R Z R U L F H
7 K H V X Q U R R I P D \ Q R W Z R U N S U R S H U O \ D Q G
P D \ E U H D N L I R S H Q H G E \ I R U F H
[ ' R Q R W R S H Q R U G U L Y H Z L W K W K H V X Q U R R I J O D V V R S H Q L P P H G L D W H O \ D I W H U U D L Q R U
Z D V K L Q J W K H Y H K L F O H : D W H U P D \ Z H W W K H
L Q W H U L R U R I W K H Y H K L F O H
[ ' R Q R W H [ W H Q G D Q \ O X J J D J H R X W V L G H W K H V X Q U R R I Z K L O H G U L Y L Q J 9 H K L F O H G D P D J H
P D \ R F F X U L I W K H Y H K L F O H V X G G H Q O \
V W R S V
WARNING Do not extend your head, arms, body
parts or objects outside the sunroof while
driving. Injuries may occur if the vehicle
suddenly stops.
Resetting the sunroof
B5027801
In some circumstances resetting the
sunroof operation may need to be
performed. Some instances where
resetting the sunroof may be required
include:
• When the 12 V battery is either disconnected or discharged
• When the sunroof fuse is replaced
• If the sunroof one-touch AUTO OPEN/CLOSE operation is not
functioning properly
Sunroof resetting procedure:
1. It is recommended to perform the reset procedure with the vehicle running.
Start the vehicle in P (Park).
2. Make sure the power sunshade and sunroof glass are in the fully closed
position. If the power sunshade and
sunroof glass are open, push the switch
forward until the power sunshade and
sunroof glass are fully closed.
3. Release the switch when the power sunshade and sunroof glass are fully
closed.
4. Push the switch forward until the power sunshade and sunroof glass move
slightly. Then release the switch.
5. Once again push and hold the sunroof switch forward until the power
sunshade and sunroof glass slide open
Hyundai_CE_en_US.book Page 52
Page 231 of 582
5
5-53
and close. Do not release the switch
until the operation is completed.
If you release the switch during
operation, start the procedure again
from step 2.
Information If the sunroof is not reset after the vehicle
battery is disconnected or discharged, or the
sunroof fuse is blown, the sunroof may not
operate normally.
Sunroof open warning
B5027901
If the driver turns off the vehicle when the
sunroof is not fully closed, the warning
chime will sound for several seconds and
the sunroof open warning will appear on
the cluster display. Close the sunroof
securely when leaving your vehicle.
CAUTION Make sure the sunroof is closed fully
when leaving your vehicle. If the sunroof
is left open, rain or snow may wet the
interior of the vehicle. Also, leaving the
sunroof open when the vehicle is
unattended may invite theft.
Hood
Opening the Hood
B5010001
1. Park the vehicle and apply the parking brake.
2. Pull the release lever to unlatch the hood. The hood pops open slightly.
B5010002
3. Go to the front of the vehicle, raise the hood slightly, push to the left the
secondary hood release lever (1) inside
of the hood center and lift the hood (2).
Closing the Hood
1. Before closing the hood, check in and around the motor compartment to
ensure the following:
• Any tools or other loose objects have been removed.
• All glove, rags, or other combustible material have been removed.
Hyundai_CE_en_US.book Page 53
Page 234 of 582
Convenience Features
5-56
repeatedly to prevent battery
discharge.
• Do not leave the trunk open for a long period of time. This may drain the
battery.
• Do not modify or repair any part of the power trunk by yourself. Contact an
authorized HYUNDAI dealer.
• Do not operate the power trunk under the following conditions. The power
trunk may not operate properly.
- One side of the vehicle is lifted to inspect the vehicle or change a tire
- Parking on an uneven road such as a slope, etc.
• Close the trunk completely and lock all doors and trunk using the central door
lock button before using an automatic
car wash.
• Do not spray high pressure water directly on the power trunk outside
open/close button. The trunk may open
unintentionally.
Information • In cold and wet climates, the outside power trunk open button may not work properly
due to freezing conditions. If this occurs,
remove the ice before using the outside
power trunk open/close button or use the
power trunk open/close button on the smart
key or the instrument panel.
• If you leave the smart key in the trunk and close the trunk, a warning will sound for
about 5 seconds. If this occurs, open the
trunk by pressing the power trunk open
button on the outside of the trunk.
• If there are obstacles such as snow on the trunk, the trunk may not open
automatically. After removing the obstacle,
try to open it again.
• Be careful where there is an incline, as the trunk lid may drop slightly when it is
stopped before it fully opens.
Operating the Power Trunk
Power trunk open button (Smart
key)
B5011101
When the trunk is closed, press the power
trunk open button for 1.5 second. The
trunk will open with a warning sound.
While the trunk is opening, press the
button to stop power trunk operation.
Power trunk open/close button
(Instrument panel)
B5011102
When the trunk is closed, press the power
trunk open/close button. The power trunk
will open with a warning sound.
While the trunk is opening, press the
button to stop power trunk operation.
When the trunk is opened, press and hold
the trunk open/close button to close the
power trunk. If you release the button
while the trunk is closing, power trunk
operation will stop with a warning sound
for 5 seconds.
Hyundai_CE_en_US.book Page 56