2023 HYUNDAI IONIQ 6 battery

6
6-17
(Drive) while the function is on. i-PEDAL
is disabled and regenerative braking
level is set to 3.
CAUTION • Depending on the vehicle and road condition, the vehicle may not come to
a stop although the i-PEDAL function is
active. Check surroundings and
depress the brake pedal to control the
vehicle speed.
• Do not use i-PEDAL on slippery roads.

i-PEDAL limitations
In the following conditions, the vehicle
may not come to a stop although the
i-PEDAL is properly activated. Depress
the brake to stop the vehicle when:
• Driving on a slope, or when the vehicle is repeatedly driven and stopped.
• The vehicle is driving through the end of the slope.
• Driving on a slippery surface such as an icy, rainy, or muddy road.
• The wheels are not properly aligned.
• A wheel slip or wheel spin occurs.
• The weight on board is heavy.
• The vehicle is tilted to the side.
• The tire is worn out.
Smart Regeneration
System
The smart regeneration system
recognizes vehicle-to-vehicle distance,
road gradient, and speed cameras and
controls the regenerative braking level
while coasting. It reduces unnecessary
depressing of pedals to improve fuel
efficiency and driver convenience.
Information • Coasting is the process of driving a vehicle without the brake pedal and the accelerator
depressed. Coasting uses the inertia of
driving energy instead of the vehicle power.
• The regenerative braking system uses the electric motor to engage the brake. The
electric motor converts the kinetic energy
generated from decelerating the vehicle to
electricity and charges the high voltage
battery.

Smart Regeneration System
On/Off
Operate the paddle shifter as shown
below to use the smart regeneration
system.
• Turning on the smart regeneration system: While the indicator is on,
shift the gear to D (Drive), and pull and
hold the right paddle shifter ( ) for
over a second.
Hyundai_CE_en_US.book Page 17

6
6-25
To release EPB (Electronic Parking Brake)
automatically:
• Gear in P (Park)With the vehicle on ( indicator on)
depress the brake pedal and shift out of
P (Park) to R (Reverse) or D (Drive).
• Gear in N (Neutral) With the vehicle on ( indicator on)
depress the brake pedal and shift out of
N (Neutral) to R (Reverse) or D (Drive).
• Satisfy the following conditions 1. Ensure seat belts are fastened and the doors, hood and trunk are closed.
2. With the vehicle on ( indicator on), depress the brake pedal and shift
out of P (Park) to R (Reverse), D
(Drive) or Manual shift mode.
3. Depress the accelerator pedal.
Make sure the Parking Brake warning light
goes off.
Information • You can engage EPB even though the Start/Stop button is in the OFF position
(only if battery power is available), but you
cannot release it.
• Depress the brake pedal and release the parking brake manually with the EPB
switch before you drive downhill or when
backing up.

NOTICE
[ ,IWKH3DUNLQJ%UDNHZDUQLQJOLJKWLVVWLOO RQHYHQWKRXJKWKH(3%KDVEHHQ
UHOHDVHGKDYHWKHV\VWHPLQVSHFWHGE\
DQDXWKRUL]HG+<81'$,GHDOHU

[ 'RQRWGULYH\RXUYHKLFOHZLWK(3% DSSOLHG,WPD\FDXVHH[FHVVLYHEUDNH
SDGDQGEUDNHURWRUZHDU

Warning messages
To release EPB, close the doors, hood and
trunk and fasten the seatbelt
B6003804
If the driver's seat belt is unfastened, or
the hood, trunk, doors are open, and you
try to drive with EPB applied, a warning
sounds and a message appears.
WARNING To prevent serious injury or death from
unintended vehicle movement:
• Always come to a complete stop and continue to depress the brake pedal
before parking, shift the gear into P
(Park), pull up the EPB switch, and press
the Start/Stop button to the OFF
position. Take the key with you when
leaving the vehicle.
• Never allow anyone who is unfamiliar with the vehicle to touch the EPB
switch.
• Only release EPB when you are seated inside the vehicle with your foot firmly
on the brake pedal.

NOTICE'ULYLQJZLWKWKHSDUNLQJEUDNHRQPD\
RYHUKHDWWKHEUDNLQJV\VWHPDQGFDXVH
SUHPDWXUHZHDURUGDPDJHWREUDNH
SDUWV

5P
SFMFBTF
&1#
GBTUFO
TFBUCFMU
BOE DMPTF
EPPS

IPPE BOE
USVOL
Hyundai_CE_en_US.book Page 25

6
6-31
NOTICE:KHQ\RXGULYHRQDURDGKDYLQJSRRU
WUDFWLRQVXFKDVDQLF\URDGDQGDSSO\
\RXUEUDNHVFRQWLQXRXVO\$%6ZLOOEH
DFWLYHFRQWLQXRXVO\DQGWKH$%6 \f
ZDUQLQJOLJKWPD\LOOXPLQDWH3XOO\RXU
YHKLFOHRYHUWRDVDIHSODFHDQGWXUQWKH
YHKLFOHRII
5HVWDUWWKHYHKLFOH,IWKH$%6ZDUQLQJ
OLJKWLVRIIWKHQ\RXU$%6V\VWHPLV
QRUPDO
2WKHUZLVH\RXPD\KDYHDSUREOHPZLWK
\RXU$%6V\VWHP&RQWDFWDQDXWKRUL]HG
+<81'$,GHDOHUDVVRRQDVSRVVLEOH

Information When you jump start your vehicle because of
a drained battery, the ABS ( ) warning
light may turn on at the same time. This
happens because of the low battery voltage. It
does not mean your ABS is malfunctioning.
Have the battery recharged before driving the
vehicle.

Electronic Stability Control
(ESC)
B6004101
Electronic Stability Control helps to
stabilize the vehicle during cornering
maneuvers.ESC checks where you are steering and
where the vehicle is actually going. ESC
applies braking pressure to any one of the
vehicle's brakes and intervenes in the
electric vehicle control system to assist
the driver with keeping the vehicle on the
intended path. It is not a substitute for
safe driving practices. Always adjust your
speed and driving to the road conditions.
WARNING Never drive too fast for the road
conditions when cornering. ESC will not
prevent accidents.
Excessive speed in turns, abrupt
maneuvers, and hydroplaning on wet
surfaces can result in severe accidents.

ESC operation
ESC ON condition
When the Start/Stop button is in the ON
position, ESC and the ESC OFF indicator
lights illuminate for about 3 seconds.
After both lights go off, ESC is enabled.
When operating
When ESC is in operation, the ESC
indicator light blinks:
• When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your ESC is active.
• When ESC activates, the vehicle may not respond to the accelerator as it
does under routine conditions.
Hyundai_CE_en_US.book Page 31

6
6-47
“Tire Replacement” section in Chapter
9.
• Turn on your headlights to make it easier for others to see you. Using your
headlights when using your windshield
wipers is required in some jurisdictions.
• Driving too fast through large puddles may affect your brakes. If you must go
through puddles, try to drive through
them slowly.
• If you believe your brakes are wet, apply them several times while the
vehicle is moving slowly.
Hydroplaning
If the road is wet enough and you are
going fast enough, your vehicle may have
little or no contact with the road surface
and actually ride on the water. The best
advice is SLOW DOWN when the road is
wet.
The risk of hydroplaning increases as the
depth of tire tread decreases, For more
information, refer to the “Tire
Replacement” section in chapter 9.
Driving in Flooded Areas
Avoid driving through flooded areas
unless you are sure the water is not
deeper than the bottom of the wheel hub.
If you are not sure, turn around and find a
different route. Drive through any water
slowly. Allow adequate stopping distance
because the brake performance can be
reduced.
After driving through water, dry the
brakes by gently applying them several
times while the vehicle is moving slowly.
Highway Driving
Tires
Adjust the tire inflation pressure, as
specified. Under-inflation may overheat
or damage the tires.
Do not install worn-out or damaged tires,
which may reduce traction or fail.
Information Never over-inflate your tires above the
maximum inflation pressure, as specified on
your tires.

Coolant and high voltage battery
Driving at higher speeds on the highway
consumes more electric energy and is
less efficient than driving at a slower,
more moderate speed. Maintain a
moderate speed in order to conserve
electric energy when driving on the
highway.
Be sure to check both the coolant level
and the electric energy level before
driving.
Hyundai_CE_en_US.book Page 47

6
6-51
Check battery and cables
Winter temperatures affect battery
performance. Inspect the battery and
cables, as specified in chapter 9. The
battery charging level can be inspected
by an authorized HYUNDAI dealer or in a
service station.
To prevent locks from freezing
Spray approved de-icing fluid or glycerin
into key holes. When a lock opening is
already covered with ice, spray approved
de-icing fluid over the ice to remove it.
When an internal part of a lock freezes, try
to thaw it with a heated key. Carefully use
the heated key to avoid an injury.
Use approved window washer anti-freeze
solution
Add authorized window washer
anti-freeze solution, as specified on the
window washer container. Window
washer anti-freeze solution is available
from an authorized HYUNDAI dealer, and
most vehicle accessory outlets. Do not
use coolant or other types of anti-freeze
solution, to prevent any damage to the
vehicle paint.
Do not let your parking brake freeze
Under some conditions, your parking
brake may freeze in the engaged position.
This is most likely to happen when there is
an accumulation of snow or ice around or
near the rear brakes or the brakes are wet.
When there is the risk that your parking
brake may freeze: temporarily apply the
parking brake with the gear in P (Park),
then block the rear wheels, and then
release the parking brake.Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
may build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, check underneath the vehicle on a
regular basis, to make sure that the front
wheels and the steering components are
not blocked.
Carry emergency equipment
In accordance with weather conditions,
carry appropriate emergency equipment,
while driving. Some of the items you may
want to carry include tire chains, tow
straps or chains, flashlight, emergency
flares, sand, shovel, jumper cables,
window scraper, gloves, ground cloth,
coveralls, blanket, etc.
Do not place objects or materials in the
motor compartment
Putting objects or materials in the motor
compartment may cause a motor failure.
Such damage is not be covered by the
manufacturer’s warranty.
Hyundai_CE_en_US.book Page 51

Driver Assistance System
7-132
2. Remotely moving forward and
backward
B7008812
1. Press and hold one of the Forward ( ) or Backward ( ) button on the smart
key.
• Remote Smart Parking Assist will automatically control the steering
wheel, vehicle speed and gearshift.
The vehicle will move in the direction
of the button pressed.
• While Remote Operation function is operating, if the you let the button,
the vehicle will stop and function
control will pause. The function will
start operating again when the
button is pressed and held again.
2. Hold down the Forward ( ) or Backward ( ) button until the vehicle
reaches the target location.
3. When Remote Operation is done, get in the vehicle with the smart key or press
the Remote Start ( ) button on the
smart key from outside the vehicle.
• The message will appear on the infotainment system. The vehicle will
automatically shift to P (Park) and
engage the parking brake.
• When the Remote Start ( ) button is pressed, the vehicle will turn off. If
the driver is in the vehicle, the vehicle
will retain ON position.
Information • Remote Operation can control the vehicle remotely using the smart key outside the
vehicle.
• Check that all smart keys are outside the vehicle when using Remote Operation
function.
• Remote Operation function will operate only when the smart key is within 13 ft. (4
m) from the vehicle. If there is no vehicle
movement even when the Forward or
Backward button is pressed on the smart
key, check the distance to the vehicle and
press the button again.
• The detecting range of the smart key may vary depending on the surroundings that are
affected by radio waves such as
transmission tower, broadcast station, etc.
• When remotely moving forward using Method 1, it is recognized as an exit
situation, and the vehicle moves 13 ft. (4 m)
to check for parking lines, pedestrians,
animals or objects around the vehicle. After
confirmation, the steering wheel is
controlled according to the condition ahead.
• When remotely moving forward using Method 2, it is recognized as a parking
situation, and will immediately control the
steering wheel according to the condition
ahead to assist with entering the parking
space and aligning the vehicle. However,
performance may reduce depending on the
parking lines, pedestrians, animals, shape
of objects, location, etc., around the vehicle.
• For moving remotely backward, both Method 1 and 2 aligns the steering wheel
first, and then will only move the vehicle
straight.

WARNING • When using Remote Operation function, make sure that all passengers
have gotten out of the vehicle.
• If the vehicle’s battery is discharged or Remote Smart Parking Assist
Hyundai_CE_en_US.book Page 132

Driver Assistance System
7-134
• Button of another smart key is pressed in addition to the operating smart key
(except Remote Start button)
• Blind-Spot Collision Warning or Rear Cross-Traffic Collision-Avoidance
Assist operates while the vehicle is
being controlled in the reverse
direction.
• The vehicle moves 22 ft. (7 m) while the smart key is pressed with Remote
Operation function (maximum travel
distance per button press)
The function will cancel in the following
conditions when:
When Remote Operation function is
canceled, the vehicle will automatically
stop, shift the gear to P (Park) and engage
EPB (Electronic Parking Brake).
• The steering wheel is steered
• The gear is shifted while the vehicle is moving
• Operating EPB while the vehicle is moving
• The hood is open
• The brake pedal or accelerator pedal is depressed when all the doors are
closed
• The smart key is outside the vehicle when the brake pedal is depressed
while the driver's door is open
• Rapid acceleration occurs
• Vehicle skid occurs
• The wheel is stuck by an obstacle and cannot move
• About 3 minutes and 50 seconds has passed after Remote Operation
function has started to operate
• The slope of the road exceeds the operational range
• The function is paused for more than 1 minute
• The total travel distance of the vehicle has exceeded 45 ft. (14 m) after Remote
Operation function operation • The steering wheel, gearshift, braking,
and drive controls are not working
properly
• There is a problem with the smart key or the smart key battery is low
• ABS, TCS or ESC system operates due to slippery road conditions
• The alarm of the Theft Alarm System sounds
• The charging door is open
Smart Parking, Remote Smart
Parking
The parking function includes Smart
Parking using the Parking/View ( )
button and Remote Smart Parking using a
smart key.
Operating order
Parking function operates in the following
order:
1. Getting ready for parking
2. Searching for parking space
3. Select parking type and operating mode
4. Smart Parking
5. Remote Smart Parking
1. Getting ready for parking
B7008901
1. With the vehicle turned on, depress the brake pedal and shift the gear to D
(Drive) or N (Neutral).
Hyundai_CE_en_US.book Page 134

7
7-141
- Vehicle skid occurs
- The wheel is stuck by an obstacle and cannot move
- There are pedestrians, animals or objects at the front and rear of the
vehicle at the same time
- About 3 minutes and 50 seconds have past after Smart Parking
function has started to operate
- The slope of the road exceeds the operational range
- The function is paused for more than 1 minute
- The steering wheel, gearshift, braking, and drive controls are not
working properly
- ABS, TCS or ESC system operates due to slippery road conditions
- The charging door is open
When Smart Parking function is canceled,
the vehicle will automatically stop, shift
the gear to P (Park) and engage EPB
(Electronic Parking Brake).
• Remote Smart Parking - The steering wheel is steered
- The gear is shifted
- Operating EPB while the vehicle is moving
- The hood is open
- The brake pedal or accelerator pedal is depressed when all the doors are
closed
- The smart key is outside the vehicle when the brake pedal is depressed
while the driver's door is open
- Rapid acceleration occurs
- Vehicle skid occurs
- The wheel is stuck by an obstacle and cannot move
- There are pedestrians, animals or objects at the front and rear of the
vehicle at the same time
- About 3 minutes and 50 seconds have past after Remote Smart Parking function has started to
operate
- The slope of the road exceeds the operational range
- The function is paused for more than 1 minute
- The steering wheel, gearshift, braking, and drive controls are not
working properly
- There is a problem with the smart key or the smart key battery is low
- ABS, TCS or ESC system operates due to slippery road conditions
- The alarm of the Theft Alarm System sounds
- The charging door is open
When Remote Smart Parking function is
canceled, the vehicle will automatically
stop, shift the gear to P (Park) and engage
EPB (Electronic Parking Brake).
Smart Exit
Operating order
Smart Exit function operates in the
following order:
1. Getting ready for exit
2. Checking space
3. Select exit direction
4. Smart Exit
Hyundai_CE_en_US.book Page 141