2023 HYUNDAI IONIQ 6 reset

5
5-53
and close. Do not release the switch
until the operation is completed.
If you release the switch during
operation, start the procedure again
from step 2.
Information If the sunroof is not reset after the vehicle
battery is disconnected or discharged, or the
sunroof fuse is blown, the sunroof may not
operate normally.

Sunroof open warning
B5027901
If the driver turns off the vehicle when the
sunroof is not fully closed, the warning
chime will sound for several seconds and
the sunroof open warning will appear on
the cluster display. Close the sunroof
securely when leaving your vehicle.
CAUTION Make sure the sunroof is closed fully
when leaving your vehicle. If the sunroof
is left open, rain or snow may wet the
interior of the vehicle. Also, leaving the
sunroof open when the vehicle is
unattended may invite theft.

Hood
Opening the Hood
B5010001
1. Park the vehicle and apply the parking brake.
2. Pull the release lever to unlatch the hood. The hood pops open slightly.
B5010002
3. Go to the front of the vehicle, raise the hood slightly, push to the left the
secondary hood release lever (1) inside
of the hood center and lift the hood (2).
Closing the Hood
1. Before closing the hood, check in and around the motor compartment to
ensure the following:
• Any tools or other loose objects have been removed.
• All glove, rags, or other combustible material have been removed.
Hyundai_CE_en_US.book Page 53

Convenience Features
5-58
Automatic reverse
During power trunk operation if the
power trunk senses any obstacle, the
trunk will stop or will fully open. The
automatic reverse feature may not
operate properly, or it may operate
unexpectedly under the following
circumstances:
• The automatic reverse feature may not detect the resistance if the detected
resistance is below a certain level, or if
the trunk is almost fully closed near the
latched position.
• The automatic reverse feature may operate if a strong impact is applied
with no obstructions placed.
WARNING Never intentionally place any object or
part of your body in the path of the power
trunk to make sure the automatic reverse
feature operates. Serious injury, or
damage to the vehicle or object may
occur.

Information The power trunk may stop operating if the
automatic reverse feature operates more than
two times while attempting to open or close
the trunk. If this occurs, carefully open or
close the trunk manually, and then after 30
seconds try to operate the power trunk
automatically again.

Resetting the Power Trunk
To reset the power trunk:
1. With the vehicle is turned off or on ( indicator off or on), put the gear in P
(Park).
2. While Pressing the power trunk close inner button, press the power trunk
open outer button for more than 3
seconds. A chime will sound. 3. Slowly close the trunk manually.
4. Press the power trunk open outer
button. The trunk will open with a
chime sound.
Wait until the trunk fully opens to
complete resetting. If the trunk stops
before it is fully open, resetting cannot
be completed.
Information • If the power trunk is not reset after the vehicle battery is disconnected or
discharged, or the power trunk fuse is
blown, the power trunk may not operate
normally.
• If the power trunk does not operate properly after the above procedure, have the system
inspected by an authorized HYUNDAI
dealer.

Emergency Trunk Safety
Release
B5011701
• Inside the trunk
Your vehicle is equipped with an
emergency trunk safety release lever
located inside the trunk. When
someone is inadvertently locked in the
trunk, the trunk can be opened by
moving the lever in the direction of the
arrow and pushing the trunk lid to open.
Hyundai_CE_en_US.book Page 58

5
5-95
3. Touch the defroster icon ( ).
4. When Defogging logic is enabled, Fresh mode is selected and air conditioning is
selected according to outside
temperature.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, touch the
icon once to enable Fresh mode
(indicator light OFF).
If the position is selected, lower fan
speed is adjusted to a higher fan speed.
Defogging Logic
To reduce the probability of fogging up
the inside of the windshield, the air intake
or air conditioning are controlled
automatically according to certain
conditions such as positions. To cancel
or reset the defogging logic, do the
following.
1. Press the Start/Stop button to the ON position.
2. Touch the defroster icon ( ) or ( ).
3. While touching the A/C icon, touch the air intake control icon at least 5 times
within 3 seconds.
The air intake control indicator will blink 3
times to indicate that the defogging logic
has been disabled. Repeat the steps again
to re-enable the defogging logic.
The air intake control indicator will blink 6
times to indicate that the defogging logic
has been enabled.
If the battery has been discharged or
disconnected, it resets to the defog logic
status.
Rear Window Defroster
NOTICE To prevent damage to the rear window
defroster conducting elements bonded to
the inside surface of the rear window,
never use sharp instruments or window cleaners containing abrasives to clean the
window.

B5020801
The defroster heats the window to
remove frost, fog and thin ice from the
interior and exterior of the rear window,
while the vehicle is running.
• To activate the rear window defroster,
touch the rear window icon located in
the center control panel. The indicator
on the rear window defroster
illuminates when the defroster is on.
• To turn off the defroster, touch the rear window defroster button again.
Information • If there is heavy accumulation of snow on the rear window, brush it off before
operating the rear defroster.
• The rear window defroster automatically turns off after about 20 minutes or when the
Start/Stop button is in the OFF position.

Side view mirror defroster
If your vehicle is equipped with the
rearview mirror defrosters, they will
operate at the same time you turn on the
rear window defroster.
Hyundai_CE_en_US.book Page 95

Convenience Features
5-98
Turning Auto Dehumidify ON or OFF
Climate control system
To turn the Auto Dehumidify feature on or
off, select Face level ( ) mode and touch
the air intake control icon at least five
times within three seconds. When Auto
Dehumidify is turned on, the air intake
control button indicator will blink 6 times.
When turned off, the indicator will blink 3
times.
Infotainment system
Auto Dehumidify can be turned on and off
by selecting Setup > Vehicle > Climate >
Automatic Ventilation > Auto
Dehumidify from the infotainment
system.
Information If the battery (12 V) is discharged or
disconnected, Auto dehumidify settings will
be reset. Readjust the settings to turning Auto
dehumidify option ON or OFF.

NOTICE7KHLQIRWDLQPHQWV\VWHPPD\FKDQJH
DIWHUVRIWZDUHXSGDWHV)RUPRUH
LQIRUPDWLRQUHIHUWRWKHXVHU
VPDQXDO
SURYLGHGLQWKHLQIRWDLQPHQWV\VWHPDQG
WKHTXLFNUHIHUHQFHJXLGH

Sunroof Inside Air
if equipped
recirculation
When the is sunroof opened, fresh mode
will be automatically selected. At this
time, if you press the air intake control
button, recirculation mode will be
selected but will change back to fresh
mode after 3 minutes. When the sunroof
is closed, the air intake position will return
to the original position that was selected.
Recirculating Air When
Washer Fluid Is Used
Recirculation mode automatically
activates to reduce any objectionable
scent of the washer fluid from entering
the cabin when the windshield washer is
used.
Turning Activate upon Washer Fluid
Use ON or OFF
Activate upon Washer Fluid Use can be
turned on and off by selecting Setup >
Vehicle > Climate > Internal air
circulation > Activation on washer fluid
use from the infotainment system.
Information The infotainment system may change after
software updates. For more information, refer
to the user's manual provided in the
infotainment system and the quick reference
guide.

if equipped
Recirculation Mode Plus
• To prevent the inflow of polluted air
into the vehicle when passing through a
tunnel, this function automatically
closes the windows and switches the
climate control system to Recirculation
mode for about 7 seconds before
entering a tunnel based on the map
information of the navigation and the
speed of the vehicle.
• The windows automatically closes before entering a tunnel and area
requiring air recirculation. The windows
open to the previous position after
passing the area. If the power window
switch is operated before the window
opens, the window does not open to
the previous position.
• Tunnel linkage automatic control is available only for models with
Hyundai_CE_en_US.book Page 98

Convenience Features
5-108
Antenna
B5025101
The shark fin antenna will receive AM, FM
broadcast signals and transmit data.
Steering Wheel Remote
Controls
B5025401
NOTICE'RQRWRSHUDWHPXOWLSOHDXGLRUHPRWH
FRQWUROEXWWRQVVLPXOWDQHRXVO\

VOLUME (VOL + / VOL -) (1)
• Rotate the VOLUME scroll up to increase volume.
• Rotate the VOLUME scroll down to decrease volume.
Information You can set the volume level of each source
(FM, AM, SXM, USB, BT, etc.) individually
by adjusting the VOLUME scroll.
Then the infotainment system saves the last
volume level of each source in the system
sound settings.
If you change the source, the volume will
revert to the previously set volume for that
source.

SEEK/PRESET ( / ) (2)
If the SEEK/PRESET switch is pressed up
or down and held for 0.8 second or more,
it will function in the following modes:
RADIO mode
It will function as the AUTO SEEK select
button. It will SEEK until you release the
button.
MEDIA mode
It will function as the FF/RW button.
If the SEEK/PRESET switch is pressed up
or down, it will function in the following
modes:
RADIO mode
It will function as the PRESET STATION
UP/DOWN button.
MEDIA mode
It will function as the TRACK UP/ DOWN
button.
MODE (3)
Press the MODE button to toggle through
Radio or AUX modes.
MUTE ( ) (4)
Press the MUTE( )button to mute or
activate the sound.
12
3
4
Hyundai_CE_en_US.book Page 108

7
7-47
Manual Speed Limit
Assist (MSLA)
B7002201(1) Speed Limit indicator
(2) Set speed
You can set the speed limit when you do
not want to drive over a specific speed.
If you drive over the preset speed limit,
Manual Speed Limit Assist will operate
(set speed limit will blink and chime will
sound) until the vehicle speed returns
within the speed limit.
Manual Speed Limit Assist
Operation
Setting speed limit
B7002301
1. Press and hold Driving Assist ( ) button at the desired speed. The Speed
Limit ( ) indicator will illuminate on
the instrument cluster.
B7002302
2. Push the + switch up or - switch down, and release it at the desired speed.
Push the + switch up or - switch down
and hold it. The speed will increase or
decrease to the nearest multiple of five
(multiple of ten in km/h) at first, and
then increase or decrease by 5 mph (10
km/h).
B7002303
3. The set speed limit will be displayed on the instrument cluster.
If you would like to drive over the preset
speed limit, depress the accelerator
pedal beyond the pressure point to
activate the kickdown function.
The set speed limit will blink and chime
will sound until you return the vehicle
speed within the speed limit.
2150MPH
50MPH
Hyundai_CE_en_US.book Page 47

Driver Assistance System
7-48
Temporarily pausing Manual Speed
Limit Assist
B7002304
Press the switch to temporarily pause
the set speed limit. The set speed limit will
turn off but the Speed Limit ( )
indicator will stay on.
Resuming Manual Speed Limit Assist
B7002305
To resume Manual Speed Limit Assist
after the function was paused, operate
the +, -, switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the instrument cluster.
If you press the switch, vehicle speed
will resume to the preset speed.
Turning off Manual Speed Limit
Assist
B7002301_1
Press the Driving Assist ( ) button to
turn Manual Speed Limit Assist off. The
Speed Limit ( ) indicator will go off.
WARNING Take the following precautions when
using Manual Speed Limit Assist:
• Always set the vehicle speed to the speed limit in your state.
• Keep Manual Speed Limit Assist off when the function is not in use, to avoid
inadvertently setting a speed. Check
that the Speed Limit ( ) indicator is
off.
• Manual Speed Limit Assist does not substitute for proper and safe driving. It
is the responsibility of the driver to
always drive safely and be aware of
unexpected and sudden situations. Pay
attention to the road conditions at all
times.

Hyundai_CE_en_US.book Page 48

Driver Assistance System
7-66
Decreasing set speed
B7002304_2
• Push the - switch down and release it immediately. The set speed will
decrease by 1 mph (1 km/h) each time
the switch is operated in this manner.
• Push the - switch down and hold it while monitoring the set speed on the
instrument cluster. The set speed will
decrease by 5 mph (10 km/h) each time
the switch is operated in this manner.
Release the switch at the speed you
want to maintain. You can decrease the
set speed to 20 mph (30 km/h).
Temporarily canceling Smart Cruise
Control
B7004306
Press the switch or depress the brake
pedal to temporarily cancel Smart Cruise
Control.
Resuming Smart Cruise Control
B7002305
To resume Smart Cruise Control after the
function was canceled, operate the +, - or switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the instrument cluster.
If you press the switch, vehicle speed
will resume to the preset speed.
WARNING Check the driving condition before using
the switch. Driving speed may sharply
increase or decrease when you press the switch.

Turning off Smart Cruise Control
B7002301
Press the Driving Assist ( ) button to
turn Smart Cruise Control off.
Hyundai_CE_en_US.book Page 66