2023 HYUNDAI I20 Stop and go

8-4
Emergency situations
IN CASE OF AN EMERGENCY WHILST DRIVING
If the engine stalls whilst driving

[Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.

[Turn on your hazard warning flasher.

[Try to start the engine again. If your
vehicle will not start, we recommend
that you contact a HYUNDAI
authorised repairer.
If the engine stalls at a
crossroad or crossing
If the engine stalls at a crossroads or
crossing, if safe to do so, move the shift
lever to the N (Neutral) position and then
push the vehicle to a safe location.
If you have a flat tyre whilst
driving
If a tyre goes flat whilst you are driving:

[Take your foot off the accelerator
pedal and let the vehicle slow down
whilst driving straight ahead. Do
not apply the brakes immediately or
attempt to pull off the road as this
may cause loss of vehicle control
resulting in an accident. When the
vehicle has slowed to such a speed
that it is safe to do so, brake carefully
and pull off the road. Drive off the
road as far as possible and park on
firm, level ground. If you are on a
divided highway, do not park in the
median area between the two traffic
lanes.

[When the vehicle is stopped, press
the hazard warning flasher button,
move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.

[Have all passengers get out of the
vehicle. Be sure they all get out on the
side of the vehicle that is away from
traffic.

[When changing a flat tyre, follow
the instructions provided later in this
chapter.

8-9
08
If your temperature gauge indicates
overheating, you experience a loss of
power, or hear loud pinging or knocking,
the engine may be overheating. If this
happens, you should:
1. Pull off the road and stop as soon as it
is safe to do so.
2. Place the shift lever in P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral (for
manual transmission/dual clutch
transmission vehicle) and set the
parking brake. If the air conditioning is
ON, turn it OFF.
3. If engine coolant is running out under
the vehicle or steam is coming out
from the bonnet, stop the engine. Do
not open the bonnet until the coolant
has stopped running or the steaming
has stopped. If there is no visible
loss of engine coolant and no steam,
leave the engine running and check
to be sure the engine cooling fan is
operating. If the fan is not running,
turn the engine off.
WARNING
Whilst the engine is
running, keep hands,
clothing and tools away
from the moving parts such
as the cooling fan and drive
belt to prevent serious
injury.4. Check for coolant leaking from the
radiator, hoses or under the vehicle. (If
the air conditioning had been in use, it
is normal for cold water to be draining
from it when you stop.)
5. If engine coolant is leaking out, stop
the engine immediately and we
recommend that you call a HYUNDAI
authorised repairer for assistance.
WARNING
NEVER remove the radiator
cap or the drain plug whilst
the engine and radiator are
hot. Hot coolant and steam
may blow out under
pressure, causing serious injury.
Turn the engine off and wait until the
engine cools down. Use extreme care
when removing the radiator cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back whilst the pressure
is released from the cooling system.
When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove it.
IF THE ENGINE OVERHEATS

8-11
08
OBC3N081002AU
ONX4E080005
(1) Low Tyre Pressure Telltale/TPMS
Malfunction Indicator
(2) Low Tyre Pressure Position Telltale
and Tyre Pressure Telltale (Shown on
the LCD display)
Check tyre pressure
ONX4E040019

[You can check the tyre pressure in the
Warning mode on the cluster.
Refer to the “LCD Display Modes” in
chapter 4.

[Tyre pressure is displayed after a few
minutes of driving after initial engine
start up.

[If tyre pressure is not displayed when
the vehicle is stopped, “Drive to
display” message will appear. After
driving, check the tyre pressure.

[The displayed tyre pressure values
may differ from those measured with a
tyre pressure gauge.

[You can change the tyre pressure
unit in the User Settings mode on the
instrument cluster.
- psi, kpa, bar (Refer to “LCD Modes”
in chapter 4).
7<5(35(6685(021,725,1*6<67(0

8-12
Emergency situations
Tyre pressure monitoring
system
WARNING
Over-inflation or under-inflation can
reduce tyre life, adversely affect
vehicle handling, and lead to sudden
tyre failure that may cause loss of
vehicle control resulting in an accident.
Each tyre, including the spare (if
provided), should be checked monthly
when cold and inflated to the inflation
pressure recommended by the vehicle
manufacturer on the vehicle placard
or tyre inflation pressure label. (If your
vehicle has tyres of a different size
than the size indicated on the vehicle
placard or tyre inflation pressure label,
you should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a tyre
pressure monitoring system (TPMS)
that illuminates a low tyre pressure
telltale when one or more of your
tyres is significantly under-inflated.
Accordingly, when the low tyre pressure
telltale illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper pressure.
Driving on a significantly under-inflated
tyre causes the tyre to overheat and can
lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and
may affect the vehicle’s handling and
stopping ability.
Please note that the TPMS is not a
substitute for proper tyre maintenance,
and it is the driver’s responsibility to
maintain correct tyre pressure, even if
under-inflation has not reached the level
to trigger illumination of the TPMS low
tyre pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator
to indicate when the system is
not operating properly. The TPMS
malfunction indicator is combined with
the low tyre pressure telltale. When
the system detects a malfunction, the
telltale will flash for approximately one
minute and then remain continuously
illuminated. This sequence will continue
upon subsequent vehicle start-ups as
long as the malfunction exists.
When the malfunction indicator is
illuminated, the system may not be able
to detect or signal low tyre pressure as
intended. TPMS malfunctions may occur
for a variety of reasons, including the
installation of replacement or alternate
tyres or wheels on the vehicle that
prevent the TPMS from functioning
properly.
Always check the TPMS malfunction
telltale after replacing one or more tyres
or wheels on your vehicle to ensure that
the replacement or alternate tyres and
wheels allow the TPMS to continue to
function properly.
NOTICE
If any of the below happens, we
recommend that you have the system
checked by a HYUNDAI authorised
repairer.
1. The Low Tyre Pressure Telltale/
TPMS Malfunction Indicator does not
illuminate for 3 seconds when the
Engine Start/Stop button is pressed
to the ON position or when the
engine is running.
2. The TPMS Malfunction Indicator
remains illuminated after blinking for
approximately 1 minute.
3. The Low Tyre Pressure Position
Telltale remains illuminated.

8-13
08
Low tyre pressure
warning light
Low tyre pressure position and
tyre pressure telltale
ONX4E040019
When the tyre pressure monitoring
system warning indicators are
illuminated and a warning message
displayed on the cluster LCD display,
one or more of your tyres is significantly
under-inflated. The Low Tyre Pressure
Position Telltale will indicate which
tyre is significantly underinflated by
illuminating the corresponding position
light.
If either telltale illuminates, immediately
reduce your speed, avoid hard cornering
and anticipate increased stopping
distances. You should stop and check
your tyres as soon as possible. Inflate the
tyres to the proper pressure as indicated
on the vehicle’s placard or tyre inflation
pressure label located on the driver’s
side centre pillar outer panel.If you cannot reach a service station or
if the tyre cannot hold the newly added
air, replace the low pressure tyre with
the spare tyre.
The Low Tyre Pressure Telltale will
remain on and the TPMS Malfunction
Indicator may blink for one minute
and then remain illuminated (when
the vehicle is driven approximately 10
minutes at speed above 15.5 mph (25
km/h)) until you have the low pressure
tyre repaired and replaced on the
vehicle.
CAUTION
In winter or cold weather, the Low Tyre
Pressure Telltale may be illuminated if
the tyre pressure was adjusted to the
recommended tyre inflation pressure
in warm weather. It does not mean
your TPMS is malfunctioning because
the decreased temperature leads to a
proportional lowering of tyre pressure.
When you drive your vehicle from a
warm area to a cold area or from a cold
area to a warm area, or the outside
temperature is greatly higher or lower,
you should check the tyre inflation
pressure and adjust the tyres to the
recommended tyre inflation pressure.
WARNING
Low pressure damage
Significantly low tyre pressure makes
the vehicle unstable and can contribute
to loss of vehicle control and increased
braking distances.
Continued driving on low pressure
tyres can cause the tyres to overheat
and fail.

8-21
08
Jack label
OHYK065011/OAC3N070038TU
„Type A

„Type B
The actual Jack label in the vehicle may differ from the illustration.
For more detailed specifications, refer to the label attached to the jack.
1. Model Name
2. Maximum allowable load
3. When using the jack, set your parking brake.
4. When using the jack, stop the engine.
5. Do not get under a vehicle that is supported by a jack.
6. The designated locations under the frame
7. When supporting the vehicle, the base plate of jack must be vertical under the
lifting point.
8. Shift into Reverse gear on vehicles with manual transmission or move the shift lever
to the P position on vehicles with automatic transmission/dual clutch transmission.
9. The jack should be used on firm level ground.
10. Jack manufacture
11. Production date
12. Representative company and address

8-30
Emergency situations
ODN8079020
5. Insert the sealant bottle into the
housing (5) of the compressor so that
the bottle is upright.
6. Ensure that the compressor is
switched off, position 0.
OBC3080011
NOTICE
Securely install the sealant filling hose
to the valve. If not, sealant may flow
backward, possibly clogging the filling
hose.
OBC3N080005
7. Connect between compressor and the
vehicle power outlet using the cable
and connectors (4).
8. With the engine start/stop button
position on or ignition switch position
on, switch on the compressor and let
it run for approximately 5~7 minutes to
fill the sealant up to proper pressure.
(refer to immediately chapter 2).
The inflation pressure of the tyre
immediately filling is unimportant and
will be checked/corrected later.
Be careful not to overinflate the tyre
and stay away from the tyre whilst
filling it.
NOTICE
- Tyre pressure
Do not attempt to drive your vehicle
if the tyre pressure is below 29
PSI(200kpa). This could result in an
accident due to sudden tyre failure.
9. Switch off the compressor.
10. Detach the hoses from the sealant
bottle connector and from the tyre
valve.
Return the Tyre Mobility Kit to its storage
location in the vehicle.

8-31
08
WARNING
Carbon monoxide
Do not leave your vehicle running in
a poorly ventilated area for extended
periods of time.
Carbon monoxide poisoning and
suffocation can occur.
Distributing the sealant
11. Immediately drive approximately
4~6miles (7~10km or, about 10 mins)
to evenly distribute the sealant in the
tyre.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
Whilst driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off the
vehicle on the side of the road.
Call for road side service or towing.
When you use the Tyre Mobility Kit, the
tyre pressure valve and wheel may be
damaged by sealant, remove the sealant
stained. We recommend that the tyre
pressure valve and wheel be inspected
by an authorized HYUNDAI dealer.

Checking the tyre inflation
pressure
1. After driving approximately 4 ~6miles
(7~10km or about 10min), stop at a
safety location.
2. Connect connection hose (10) of the
compressor directly to the tyre valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tyre inflation pressure to
the recommended tyre inflation.
With the ignition switched on, proceed
as follows.
- To increase the inflation pressure :
Switch on the compressor, position
I. To check the current inflation
pressure setting, briefly switch off
the compressor.
i Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tyre pressure,
the compressor needs to be turned off.
NOTICE
- Tyre pressure valve
We recommend that you use the
sealant of tyre mobility kit from a
HYUNDAI authorised repairer. The
sealant on the tyre pressure valve and
wheel should be removed when you
replace the tyre with a new one and
we recommend that the tyre pressure
valve be inspected by an authorized
HYUNDAI dealer.