2021 YAMAHA YXZ1000R Owners Manual

9-12
9
Panel B
To remove the panel1. Remove the hood. (See page 9-10.)
2. Remove panel A.
3. Remove the top cover by removing thequick fastener screw and the bolts. 4. Remove the passenger seat cushion.
(See page 5-21.)
5. Remove the passenger seat by removing the bolts.
1. Top cover
2. Bolt
3. Quick fastener screw
2
3
1
UB5J7CE0.book Page 12 Thursday, November 26, 2020 1:37 PM

9-13
9
6. Remove the quick fastener screws andthe bolts, and then pull the panel off as
shown. To install the panel
1. Place the panel in the original position,
and then install the bolts and the quick
fastener screws.
1. Passenger seat
2. Bolt
3. Seat belt
1
3
2
2
1. Panel B
2. Quick fastener screw
3. Bolt
1
2
2
3
2
3
3
UB5J7CE0.book Page 13 Thursday, November 26, 2020 1:37 PM

9-14
9
2. Install the passenger seat by installing thebolts, and then tighten them to the spec-
ified torque.TIPMake sure that the seat frame is properly
secured. 
Place the passenger seat belt in the original
position.
3. Install the passenger seat cushion.
4. Install the top cover by installing the bolts
and quick fastener screw.
5. Install panel A and the hood.
Panels C and D
To remove a panel1. Pull the tab on the panel lock up, and then turn the panel lock 1/4 turn clock-
wise.
1. Panel BTightening torque:Passenger seat bolt:32 N·m (3.2 kgf·m, 24 lb·ft)
1
UB5J7CE0.book Page 14 Thursday, November 26, 2020 1:37 PM

9-15
9
2. Remove the panel as shown.
1. Panel C
2. Panel D
3. Tab
1. Tab
2. Panel lock
1
3
2
3
1
2
1. Panel C
1. Panel D
1
1
UB5J7CE0.book Page 15 Thursday, November 26, 2020 1:37 PM

9-16
9
To install a panel1. Place the panel in the original position.2. Turn the panel lock 1/4 turn counter-
clockwise, and then push the tab on the
p a n e l l o c k d o w n s o t h a t i t i s p o i n t i n g r e a r -
ward.
EBU3543AEngine oil and oil filterCheck the engine oil level before each opera-
tion. In addition, change the oil and the oil fil-
ter cartridge at the intervals specified in the
periodic maintenance chart.
1. Panel C
1. Panel D
1
1
Recommended engine oil: YA M A L U B E5W-30, 10W-30, 10W-40, 15W-40, 20W-
40, 20W-50
Oil quantity: Oil change only:2.50 L (2.64 US qt, 2.20 Imp.qt)
Oil change and filter replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)
UB5J7CE0.book Page 16 Thursday, November 26, 2020 1:37 PM

9-17
9
NOTICEECB03020Do not use oils with a diesel specifica-
tion of “CD” or oils of a higher quality
than specified. In addition, do not use
oils labeled “ENERGY CONSERVING II”
or higher.
 Make sure that no foreign material en-
ters the oil tank. To check the engine oil level
1. Park the vehicle on a level surface.
2. Remove panel D. (See page 9-10.)
3. Start the engine and warm it up to a nor- mal operating temperature (the engine oil
temperature should reach 60 °C [140 °F]),
then let the engine idle for a minimum of
ten seconds before turning the engine off.TIPIf the engine is cold, take the vehicle for a
short drive or let it idle for approximately ten
minutes before checking the engine oil level.
4. Remove the engine oil tank filler cap andwipe the dipstick with a clean rag.
5. Insert the dipstick back into the oil tank (without screwing it in), and then remove
it again to check the oil level.
6. If the oil level is below the tip of the dip- stick, add oil.1. Engine oil tank filler cap
2. O-ring
3. Engine oil dipstick
4. Maximum level mark
5. Tip of the engine oil dipstick
45
32
1
UB5J7CE0.book Page 17 Thursday, November 26, 2020 1:37 PM

9-18
9
TIPAdd oil a little at a time so as not to overfill be-
yond the maximum level mark. 7. Check the O-ring for damage, and re-place it if necessary.
8. Install the engine oil tank filler cap.
9. Install the panel.
To change the engine oil 1. Park the vehicle on a level surface.
2. Remove panel D. (See page 9-10.)
3. Remove the engine oil tank cover by re- moving the bolts. 4. Start the engine, warm it up for several
minutes, and then turn it off.
5. Remove the engine oil tank filler cap and the cylinder head cap.
1. Engine oil tank cover
2. Bolt
1
2
UB5J7CE0.book Page 18 Thursday, November 26, 2020 1:37 PM

9-19
9
6. Place an oil pan under the oil tank to col-lect the used engine oil. 7. Remove the oil tank drain bolt and used
gasket.
8. Place an oil pan under the engine to col- lect the used engine oil.
9. Remove the engine oil drain bolt and used gasket.1. Engine oil tank filler cap
1. Cylinder head cap
1
1
1. Engine oil tank drain bolt
2. Gasket
2
1
UB5J7CE0.book Page 19 Thursday, November 26, 2020 1:37 PM