Page 29 of 200
4-1
4
EBU31170
DESCRIPTION
EBU31180Left view
1 2,3 4 5 6
9
12
137
810
11
1. Front shock absorber
2. Brake fluid reservoir
3. Clutch fluid reservoir
4. Door
5. Shoulder bolster
6. Driver seat belt
7. Coolant reservoir 8. Air filter
9. Cargo bed
10.Muffler
11.Exhaust pipe
12.Engine
13.TransmissionUB5J7CE0.book Page 1 Thursday, November 26, 2020 1:37 PM
Page 77 of 200
6-2
6
Engine oil• Check oil level.
• Fill with oil to proper level if necessary.
6-6, 9-16
Drivetrain • Check front differential, transmission case, and rear final
gear for leakage. 6-6, 6-6, 6-6, 9-27,
9-30, 9-32
Coolant • Check coolant level in reservoir.
• Fill with coolant if necessary. 6-6, 9-34
Accelerator pedal • Check free play and for proper operation. 6-7
Seat belts • Check for proper operation and belt wear. 6-7
Passenger handhold • Check for stability and proper fastening. 6-7, 8-8
Steering • Check for proper operation. 6-7
Shift lever • Check for proper operation. 6-8
Fittings and fasteners • Check all fittings and fasteners. 6-8
Instruments, lights and
switches • Check for proper operation.
4-3, 5-2, 6-8, 9-65,
9-65
Wheels and tires • Check tire pressure and for wear and damage. 6-8, 9-56, 9-57
Axle boots • Check for damage. 9-36
ITEM
ROUTINE PAGE
UB5J7CE0.book Page 2 Thursday, November 26, 2020 1:37 PM
Page 81 of 200
6-6
6
Always place a portable fuel container on the
ground before filling it. Before removing the
container cap, touch the container with the
fuel dispenser nozzle. Keep fuel dispenser
nozzle in contact with container inlet when fill-
ing. WARNING! Never refill a fuel container
in the bed of any vehicle. Fire may result
from a build-up of static electricity. The
discharge of this build-up while refueling
can cause a spark and ignite the gasoline.[EWB03270]
EBU35680Engine oilMake sure the engine oil is at the specified
level. Add oil as necessary. (See page 9-16.)NOTICEECB03020 Do not use oils with a diesel specifica-
tion of “CD” or oils of a higher quality
than specified. In addition, do not use
oils labeled “ENE RGY CONSERVING II”
or higher.
Make sure that no foreign material en-
ters the oil tank.
EBU35322TransmissionMake sure there is no oil leaking from the
transmission case.EBU31761CoolantCheck the coolant level in the reservoir and
replenish if necessary. (See page 9-34.)EBU36020Final gearMake sure there is no oil leaking from the final
gear case.EBU36030Differential gearMake sure there is no oil leaking from the dif-
ferential gear case.Recommended engine oil type and quantity: See page 11-1.
UB5J7CE0.book Page 6 Thursday, November 26, 2020 1:37 PM
Page 151 of 200
9-34
9
4. Install the differential gear oil drain boltand its new gasket, and then tighten the
bolt to the specified torque.
5. Refill the differential gear case with the recommended oil.
6. Check the oil filler bolt gasket for dam- age, and replace it if necessary. 7. Install the differential gear oil filler bolt
and its gasket, and then tighten the bolt
to the specified torque.
8. Check for oil leakage. If oil leakage is found, check for the cause.
EBU35112CoolantThe coolant level should be checked regular-
ly. In addition, the coolant must be changed
at the intervals specified in the periodic main-
tenance chart.
1. Differential gear oil drain bolt
2. GasketTightening torque:Differential gear oil drain bolt:9.8 N·m (0.98 kgf·m, 7.2 lb·ft)
1 2
Tightening torque: Differential gear oil filler bolt:23 N∑m (2.3 kgf∑m, 17 lb∑ft)
Recommended coolant: YAMALUBE coolant
Coolant quantity: Coolant reservoir (up to full level):0.56 L (0.59 US qt, 0.49 Imp.qt)
Radiator (including all routes): 3.78 L (4.00 US qt, 3.33 Imp.qt)
UB5J7CE0.book Page 34 Thursday, November 26, 2020 1:37 PM
Page 152 of 200
9-35
9
TIPIf genuine Yamaha coolant is not available,
use an ethylene glycol antifreeze containing
corrosion inhibitors for aluminum engines and
mix with distilled water at a 1:1 ratio. NOTICEECB02190Mix antifreeze with distilled water only.
However, if distilled water is not available,
soft water may be used for refilling. Do not
use hard water or salt water since they are
harmful to the engine. To check the coolant level1. Park the vehicle on a level surface.
2. Wait for the engine to cool for an accurate
reading.
3. Look at the coolant level in the coolant
reservoir. 4. If the coolant is at or below the minimum
level mark, remove panel C. (See page
9-10.)
5. Remove the coolant reservoir cap, add coolant up to the maximum level mark,
and then install the cap. NOTICE: If cool-
ant is not available, use distilled water
or soft tap water instead. Do not use
hard water or salt water since they are
harmful to the engine. If water has
been used instead of coolant, replace
1. Maximum level mark
2. Minimum level mark
21
UB5J7CE0.book Page 35 Thursday, November 26, 2020 1:37 PM
Page 153 of 200
9-36
9
it with coolant as soon as possible,
otherwise the cooling system will not
be protected against frost and corro-
sion. If water has been added to the
coolant, have a Yamaha dealer check
the antifreeze content of the coolant
as soon as possible, otherwise the ef-
fectiveness of the coolant will be re-
duced.
[ECB01012]
6. Install the panel when finished servicing
the vehicle. To change the coolant
The coolant must be changed at the intervals
specified in the periodic maintenance chart.
Have a Yamaha dealer change the coolant.
WARNING! Never attempt to remove the
radiator cap when the engine is hot.
[EWB04250]
EBU32400
Axle bootsCheck the axle boots for holes or tears.
If any damage is found, have them replaced
by a Yamaha dealer.
1. Coolant reservoir cap
1
1. Front axle boot
1
1
UB5J7CE0.book Page 36 Thursday, November 26, 2020 1:37 PM
Page 186 of 200
9-69
9
Engine overheating
Wait for the engine to cool before removing the radiator cap. WARNING! If the engine is not
cool when removing the radiator cap, hot fluid and steam could blow out under pressure
and burn you.
[EWB03460]
Place a thick rag over the cap and remove the cap slowly to allow any re-
maining pressure to escape.
TIP Tap water can be used in an emergency. Ch ange to the recommended coolant as soon as
possible.
The engine will tend to overheat if the radiator is caked with mud, or if air was not properly bled
from the cooling system. Wait until the
engine has cooled.
Check the coolant level in the
coolant reservoir and/or radiator.
Level is OK.Level is low, check the
cooling system for leakage.
No
leakage.Leakage.
Ask a Yamaha dealer to inspect
and repair the cooling system.Add coolant. (See TIP.)
Restart the engine. If the engine overheats again, ask a
Yamaha dealer to inspect and/or repair the cooling system.
UB5J7CE0.book Page 69 Thursday, November 26, 2020 1:37 PM
Page 192 of 200
11-3
11
Final gear oil:Type:SAE 80W-90 API GL-5 Hypoid gear oil
Quantity:
0.47 L (0.50 US qt, 0.41 Imp.qt)Differential gear oil:Type:SAE 80W-90 API GL-5 Hypoid gear oil
Quantity:
0.18 L (0.19 US qt, 0.16 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level mark):0.56 L (0.59 US qt, 0.49 Imp.qt)
Radiator (including all routes):
3.78 L (4.00 US qt, 3.33 Imp.qt)Air filter:Air filter element:Wet element
Air filter oil grade:
Foam air-filter oil
Secondary air filter element: Oil-coated paper elementFuel:Recommended fuel:
Regular unleaded gasoline (Gasohol [E10] acceptable)
Minimum research octane: 91
Fuel tank capacity: 34 L (9.0 US gal, 7.5 Imp.gal)
Fuel reserve amount:
8.5 L (2.24 US gal, 1.87 Imp.gal)
Throttle body:ID mark:B5H1Spark plug (s):Manufacturer/model:NGK/CR9EB
Spark plug gap: 0.7–0.8 mm (0.028–0.031 in)Drivetrain:Primary reduction ratio:1.660 (88/53)
Secondary reduction ratio: 7.333 (46/23 x 33/9)
Final drive:
Shaft
Clutch type: Wet, multiple-disc
Transmission type: 5-speed with reverse
Gear ratio:
1st: 2.400 (36/15)
2nd:
1.545 (34/22)
3rd: 1.192 (31/26)
4th: 0.962 (25/26)
5th:
0.806 (25/31)
Reverse gear: 2.467 (28/15 x 37/28)
UB5J7CE0.book Page 3 Thursday, November 26, 2020 1:37 PM
