2021 YAMAHA YXZ1000R Owners Manual

9-20
9
TIPA “ ” mark is stamped on the crankcase
near the engine oil drain bolt. 10. Install the engine oil drain bolt with newgasket, the oil tank drain bolt with new
gasket, and then tighten the bolts to the
specified torques. 11. Add 2.00 L (2.11 US qt, 1.76 Imp.qt) of
the recommended engine oil to the oil
tank.
12. Check the O-ring for damage, and re- place it if necessary.1. Engine oil drain bolt
2. Gasket
3. “ ” mark
1 2
3
Tightening torques:Engine oil drain bolt:10 N∑m (1.0 kgf∑m, 7.4 lb∑ft)
Engine oil tank drain bolt: 16 N∑m (1.6 kgf∑m, 12 lb∑ft)
UB5J7CE0.book Page 20 Thursday, November 26, 2020 1:37 PM

9-21
9
13. Install and tighten the engine oil tank fillercap and the cylinder head cap.
14. Start the engine, warm it up for several minutes, and then turn it off.
15. Remove the engine oil tank filler cap, and then add sufficient oil of the recommend-
ed type to raise it to the maximum level
mark on the dipstick.
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down. 16. Install and tighten the engine oil tank fillercap.
17. Start the engine and let it idle for several minutes. During this time, check for oil
leakage. If any oil leaks are found, stop
the engine and check for the cause.
18. Stop the engine, wait at least ten minutes, and then check the oil level one last time.
19. Install the engine oil tank cover by install- ing the bolts.
20. Install the panel.
To change the engine oil and oil filter
1. Park the vehicle on a level surface.
2. Loosen the left and right side panels by removing the bolt as shown.
1. Engine oil tank filler cap
2. O-ring
3. Cylinder head cap
3
2
1
2
UB5J7CE0.book Page 21 Thursday, November 26, 2020 1:37 PM

9-22
9
3. Remove the rear bottom panel by remov-ing the bolts. 4. Remove the bolts, and then slide the cen-
ter bottom panel rearward to remove it.1. Left side panel
2. Right side panel
3. Bolt
3
1
3
2
1. Rear bottom panel
2. Bolt
2
1
2
2
UB5J7CE0.book Page 22 Thursday, November 26, 2020 1:37 PM

9-23
9
5. Follow steps 2–9 of the “To change theengine oil” section for the oil draining pro-
cedure.
6. Remove the oil filter cartridge with an oil filter wrench. Make sure the O-ring is re-
moved together with the oil filter car-
tridge. If the O-ring remains attached to
the crankcase, oil leakage may occur.
TIPAn oil filter wrench is available from a Yamaha
dealer. 7. Apply a light coat of clean engine oil to
the O-ring of the new oil filter cartridge.TIPMake sure that the O-ring is properly seated.
1. Center bottom panel
2. Bolt
2
2
2
2
2
1
1. Oil filter cartridge
2. Oil filter wrench
2
1
UB5J7CE0.book Page 23 Thursday, November 26, 2020 1:37 PM

9-24
9
8. Install the new oil filter cartridge, and thentighten to the specified torque. 9. Follow steps 10–20 of the “To change the
engine oil” section for the oil filling proce-
dure.
10. Slide the front portion of the center bot- tom panel into place as shown, and then
hook the left and right sides of the center
bottom panel into place.1. O-ringTightening torque:Oil filter cartridge:17 N·m (1.7 kgf·m, 13 lb·ft)
1
1. Torque wrench
1
UB5J7CE0.book Page 24 Thursday, November 26, 2020 1:37 PM

9-25
9
11. Install the center bottom panel bolts, andthen tighten them to the specified torque.1. Center bottom panel
1. Center bottom panel
1
1
1. Bolt A
2. Bolt B
3. Bolt C
1
2
3
UB5J7CE0.book Page 25 Thursday, November 26, 2020 1:37 PM

9-26
9
12. Install the rear bottom panel by installingthe bolts, and then tightening them to the
specified torque. 13. Install the side panel bolts, and then tight-
en them to the specified torque.1. Bolt A
2. Bolt B
3. Bolt CTightening torques:Bolt A:7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt C: 7 N·m (0.7 kgf·m, 5.2 lb·ft)1
3
2
3
1. Rear bottom panel
2. Bolt A
3. Bolt BTightening torques: Bolt A:7 N∑m (0.7 kgf∑m, 5.2 lb∑ft)
Bolt B: 7 N∑m (0.7 kgf∑m, 5.2 lb∑ft)
3
1
2
2
UB5J7CE0.book Page 26 Thursday, November 26, 2020 1:37 PM

9-27
9
EBU38630Why YamalubeYAMALUBE oil is a Genuine YAMAHA Partborn of the engineers’ passion and belief that
engine oil is an important liquid engine com-
ponent. We form teams of specialists in the
fields of mechanical engineering, chemistry,
electronics and track testing, and have them
develop the engine together with the oil it will use. Yamalube oils take full advantage of the
base oil’s qualities and blend in the ideal ba-
lance of additives to make sure the final oil
clears our performance standards. Thus,
Yamalube mineral, semisynthetic and syn-
thetic oils have their own distinct characters
and value. Yamaha’s experience gained over
many years of research and development into
oil since the 1960’s helps make Yamalube the
best choice for your Yamaha engine.
EBU35108Transmission oilCheck the oil level and change the transmis-
sion oil at the intervals specified in the period-
ic maintenance chart.
1. Bolt BTightening torque: Bolt B:7 N·m (0.7 kgf·m, 5.2 lb·ft)
1
1
UB5J7CE0.book Page 27 Thursday, November 26, 2020 1:37 PM