2021 RAM 1500 Owners Manual

GETTING TO KNOW YOUR VEHICLE95
RamBox Emergency Release Lever
As a security measure, an Emergency Release
Lever is built into the storage bin cover latching
mechanism.
In the event of an individual being locked inside
the storage bin, the storage bin cover can be
opened from inside of the bin by pulling on the
glow-in-the-dark lever attached to the storage
bin cover latching mechanism.
Emergency Release Lever

BED DIVIDER — IF EQUIPPED
The bed divider has two functional positions:
Divider Position
Storage Position
Divider Position
The divider position is intended for managing
your cargo and assisting in keeping cargo from
moving around the bed. There are 11 divider
slots along the bed inner panels which allow for
various positions to assist in managing your
cargo.To install the bed divider into a divider position,
perform the following:

1. Make sure the center handle is unlocked
using the vehicle key and rotate the center
handle vertically to release the divider side
gates.

Center Handle And Lock

Do not allow children to have access to the
storage bins. Once in the storage bin, young
children may not be able to escape. If
trapped in the storage bin, children can die
from suffocation or heat stroke.
In an accident, serious injury could result if
the storage bin covers are not properly
latched.
Do not drive the vehicle with the storage bin
covers open.
Keep the storage bin covers closed and
latched while the vehicle is in motion.
Do not use a storage bin latch as a
tie-down.
WARNING! (Continued)
1 — Center Handle Lock
2 — Handle
3 — Unlocked Position
4 — Locked Position
2

21_DT_OM_EN_USC_t.book Page 95

96GETTING TO KNOW YOUR VEHICLE
2. With the side gates open, position the
divider so the outboard ends align with the
intended slots in the sides of the bed.

Aligning Gate To Slots

3. Rotate the side gates closed so that the outboard ends are secured into the
intended slots of the bed.
4. Rotate the center handle horizontally to secure the side gates in the closed position.
Side Gates Closed

5. Lock the center handle to secure the panel into place.
Storage Position
The storage position for the bed divider is at the
front of the truck bed which maximizes the bed
cargo area when not in use.
To install the bed divider into the storage
position, perform the same steps as you would
for the divider position, except position the
divider fully forward in the bed against the front
panel.
Storage Position

The outboard ends should be positioned in front
of the cargo tie-down loops.

Cargo Tie-Down Loop

21_DT_OM_EN_USC_t.book Page 96

GETTING TO KNOW YOUR VEHICLE97
SLIDE-IN CAMPERS
CAMPER APPLICATIONS
Certain truck models are not recommended for
slide-in campers. To determine if your vehicle is
excluded, please refer to the “Consumer
Information Truck-Camper Loading” document
available online at ramtrucks.com. For safety
reasons, follow all instructions in this
document.
NOTE:
When a cap or pickup camper is installed on a
vehicle, an alternate Center High Mounted Stop
Light (CHMSL) must be provided.
TRI-FOLD TONNEAU COVER — IF EQUIPPED
The Tri-Fold Tonneau Cover can be installed on
the truck bed to protect your gear and cargo.
TONNEAU COVER COMPONENTS

Folded Tonneau Components Tonneau Cover Latch Components

WARNING!
To avoid inhaling carbon monoxide, which is
deadly, the exhaust system on vehicles
equipped with “Cap or Slide-In Campers”
should extend beyond the overhanging
camper compartment and be free of leaks.
1 – Stowage Strap
2 – Tonneau Bumper Folded
1 — Handle
2 — Slide Locking Lever
3 — Locating Bumper
4 — Truck Flange Bead
5 — Latch Bumper
6 — J Hook
2

21_DT_OM_EN_USC_t.book Page 97

98GETTING TO KNOW YOUR VEHICLE

Position One (Front Latches Latched And Stowage
Straps Secured)
Position Two (Front And Rear Latches Latched)

TRI-FOLD TONNEAU COVER FOLDING
F
OR DRIVING OR REMOVAL
To remove the Tonneau Cover use the following
steps:

1. Open the tailgate to access the rear pair of
Tonneau Cover latches located on the
underside of the Cover.

Location Of Rear Latches Slide Locking Lever Inward

2. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull
the handle downward into the released
position.

Unlatching Latch

1 — Panel 1
2 — Panel 2
3 — Panel 3

21_DT_OM_EN_USC_t.book Page 98

GETTING TO KNOW YOUR VEHICLE99

Released Position
Hold The Bumper And Push The Handle Up

3. Holding the bumper, push the fully released latch to the center and push up. Push the
handle firmly, locking it into the stowed
position. Repeat Steps 2 and 3 for the
opposite side latch.
Stowed Position
Lift Panel 3 And Fold Onto Panel 2

4. Lift up on Panel 3 and fold it onto Panel 2.
Correct Folding — Hold Panels Together

NOTE:
When folding the second and third panels, the
sections MUST be held together to avoid
damage to the cover material. Fold the panel
gently. Do not allow the panels to drop under
their own weight.

Incorrect Folding — Will Cause Damage

2

21_DT_OM_EN_USC_t.book Page 99

100GETTING TO KNOW YOUR VEHICLE
5. Lift up on the second and third panel and
fold them onto the first panel.

Stowage Strap Clipped

6. Unsnap the stowage strap and clip. Repeat for both straps to prevent the tonneau cover
panels from unfolding.

Position One (Front Latches Latched And Stowage Straps Secured)
NOTE:
Be sure the Tonneau Cover has been folded
completely, and the stowage straps are
engaged, before removing.

Fully Folded Tonneau Cover

NOTE:
The vehicle can be driven with the tonneau in
the folded position or can be completely
removed.
Slide Locking Lever Inward

7. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull
the handle downward into the released
position.

Unlatching Latch

CAUTION!
The folded tonneau cover must be latched by
both front latches and both front stowage
straps or damage to the tonneau cover or
vehicle may occur. Damage could occur while
driving.

21_DT_OM_EN_USC_t.book Page 100

GETTING TO KNOW YOUR VEHICLE101

Released Position
Hold The Bumper And Push The Handle Up

8. Holding the bumper, push the fully released latch to the center and push up. Push the
handle firmly, locking it into the stowed
position. Repeat Steps 2 & 3 for the
opposite side latch.
9. With two people, remove the cover.
TRI-FOLD TONNEAU COVER
I
NSTALLATION
To install the Tonneau Cover follow these steps:

1. Position the Tonneau Cover on the truck
bed and center using the locating
bumpers.

2. Locate the front pair of Tonneau Cover latches on the underside of the Cover. Slide
the locking lever toward the inside of the
truck bed and release the latch from the
stowed position, and pull the handle
downward into the released position. Do
this for both the left and right side.

Location of Front Latches Slide Locking Lever Towards Inside Of Truck
Unlatching Latch

2

21_DT_OM_EN_USC_t.book Page 101

102GETTING TO KNOW YOUR VEHICLE

Released Position

3. Swing the J Hook from the handle and push the handle to the center and up, ensuring
that the J Hook is under the truck flange.
Push up on the handle firmly, locking it into
the latched position.

J Hook Under Truck Flange
NOTE:
Make sure the bumper is in front of the truck
flange bead.

Pull Handle Downward

4. Pull down on the handle to ensure the Slide Locking Lever is fully engaged. Do this for
both the left and right side.
5. Unclip the stowage straps, and re-snap them to the bow.
6. Unfold the Tonneau Cover to the second panel position.
Incorrect Folding — Will Cause Damage

NOTE:
When folding the second and third panels, the
sections MUST be held together to avoid
damage to the cover material. Fold the panel
gently. Do not allow the panels to drop under
their own weight.

Second Panel Position

1 — Front Of Truck
2 — J Hook

21_DT_OM_EN_USC_t.book Page 102