#
Press and hold the sliding door button until
th e sliding door has opened or closed.
The sliding door mo ves with increased forc e.
Obser vethat in such circum stances, the
bloc kage detection is less sensitive. Tostop
th e mo vement, release the sliding door but‐
to n. #
Remo vethe cause of the bloc kage atthe ear‐
liest opportunity. Ta
ilgate Opening and closing
the tailgate &
DANG ER Risk of exhaust gas poisoning
Combustion engines emit poisonous exhaust
ga ses such as carbon monoxide. Exhaust
ga ses can enter theve hicle interior if theta il‐
gate is open when the engine is running,
especially if theve hicle is in motion. #
Always switch off the engine before
opening theta ilgate. #
Never drive with theta ilgate open. *
NO
TEDama getotheta ilgate caused by
obs tacles ab ovetheve hicle The
tailgate swings rear wa rds and upwards
when it is opened. #
Make sure that there is suf ficient space
behind and ab ovetheta ilgate. %
Yo
u will find de tails of theta ilgate opening
dimensions under "Technical data"
(/ page 276). #
Toopen: push button 1onthe handle and
ra ise theta ilgate. #
Toclose: pulltheta ilgate firm ly down wards
by loop 2and close it from outside.
Opening the tailgate in an emer gency
If th e battery voltage is low or thevo ltage supply
is inter rupte d,theta ilgate cannot be opened.
In an emer gency, you can open theta ilgate using
th ere lease cat chfor service purposes. #
Prise off the co ver on the lo wer part of the
ta ilgate with a suitable tool, e.g. the scr ew‐
driver from theve hicle tool kit. #
Insert the scr ewdriver into the opening and
mo vethere lease le ver until theta ilgate
unloc ksand opens. #
Lift theta ilgate upwards. EAS
Y-PA CK tailgate Note
s onthe EAS Y-PA CK tailgate &
DANG ER Risk of exhaust gas poisoning
Combustion engines emit poisonous exhaust
ga ses such as carbon monoxide. Exhaust
ga ses can enter theve hicle interior if theta il‐
gate is open when the engine is running,
especially if theve hicle is in motion. #
Always switch off the engine before
opening theta ilgate. #
Never drive with theta ilgate open. *
NO
TEDama getotheta ilgate caused by
obs tacles ab ovetheve hicle The
tailgate swings rear wa rds and upwards
when it is opened. #
Make sure that there is suf ficient space
behind and ab ovetheta ilgate. %
Yo
u will find de tails of theta ilgate opening
dimensions under "Technical data"
(/ page 276). 58
Opening and closing
Inter
rupting automatic operation #
Press button 1inthe handle again.
or #
Press closing button 2intheta ilgate again.
or #
Press the008C button on theke y again for
longer than 0.5 seconds.
Ad justing the opening angle of the tail gate
Setting the end position
Yo u can set the opening angle of theta ilgate by
saving the desired position as the end position. #
Open theta ilgate and stop automatic opera‐
tion in the desired position.
or #
Open theta ilgate and manually swing it into
th e desired position. #
Press and hold the closing button 008Con
th eta ilgate until the confirmation tone
sounds once.
The cur rent position of theta ilgate has been
sa ve d as the end position.
Re setting tothe maximum opening angle #
Open theta ilgate. #
Press and hold the closing button 008Con
th eta ilgate until the confirmation tone
sounds twice.
The sa ved end position has been dele ted and
th eta ilgate opens again tothe maximum
ex tent.
Re setting the tailgate
Yo u must reset theta ilgate if there has been a
malfunction or an inter ruption in thevo ltage sup‐
ply. #
Ifth eta ilgate is open: close theta ilgate by
hand. #
Brief lypress the button in the handle of the
ta ilgate, step out of the swinging range of the
ta ilgate and open thetai lgate. #
When theta ilgate is fully open, press the
008C closing button in theta ilgate and step
out of the swinging range of theta ilgate.
The tailgate closes. When thetai lgate is fully
closed, it is reset and operational.
% When the008C button of theke y is prog ram‐
med for operating theta ilgate (/ page61),
yo u can also use theke yto open and close
th eta ilgate. Opening and closing
there ar window &
DANG ER Risk of poisoning from exhaust
ga ses
Combustion engines emit poisonous exhaust
ga ses, such as carbon monoxide. Exhaust
ga ses can enter theve hicle interior if there ar
wind owis open when the engine is running,
especial lyifth eve hicle is in motion. #
Always switch off the engine before
opening there ar wind ow. #
Never drive with there ar wind owopen. Re
quirements
R The vehicle or load compartment is unloc ked
and theta ilgate is closed.
R To
open using theke y:
- The vehicle is equipped with an EAS Y-
PA CK tailgate and the008C button on the
ke y is prog rammed toopen there ar win‐
dow (/ page61) or theve hicle is
equipped with the Bunk Package.
Opening #
Press the008C button on thekey.
or #
Press button 1onthe handle on there ar
wind ow.
Closing #
Swing there ar wind owdown and push it
closed. 60
Opening and closing
#
Tosto p automatic ope ration: push or pull
th e0057 button be yond the point of resist‐
ance and release it.
Yo u will still be able tooperate the sliding sunroof
if yo u swit choff the engine or remo vethekey.
This function will remain available for 30 seconds
or until you open a front door.
When the po wer supp lyis switched off, the slid‐
ing sunroof will close automatically in thefo llow‐
ing situations:
R If it starts torain
R Intheeve nt of extreme outside temp eratures
R After six hours
R Ifth ere is a malfunction in the po wer supply
The sliding sunroof will remain raised at there ar
to allow theve hicle interior tocontinue tobe ven‐
tilated.
The sliding sunroof will not close in thefo llowing
situations:
R Ifth e sliding sunroof is raised at there ar.
R Ifth e sliding sunroof is obstructed.
R If it is not raining on thefield of thera in sen‐
sor on the windscreen because theve hicle is
underneath a bridge, forex ample.
If th e sliding sunroof closes via thera in closing
function and is obstructed in the process, it will
open again slightl y.The rain closing function will
th en be disabled. Opening and closing
thero ller sunblinds of
th e sliding sunroof &
WARNING Risk of becoming trapped
when thero ller sunblind is being opened
and closed
Body parts may become trapped between the
ro ller sunblind and frame or sliding roof. #
When opening or closing, make sure
that no body parts are in thero ller sun‐
blind's range of mo vement. #
Release the button immediately if some‐
body becomes trapped.
or #
Brief lypress the button in any direction
during automatic operation.
The opening or closing process will be
st opped. Re
quirements
R The po wer supply has been switched on.
Re versing function of thero ller sunblind
Yo u can open and close thero ller sunblind only
when the sliding sunroof is closed.
The roller sunblinds are fitted wi than automatic
re ve rsing function. If a solid object pr events or
hinders the closing process, thero ller sunblind
will open again automaticall y.The automatic
re ve rsing function is only an aid and is not a sub‐
st itute foryo ur attentiveness in the process of
closing thero ller sunblinds. #
When closing thero ller sunblind, make sure
th at no body parts are in thera nge of mo ve‐
ment. &
WARNING Risk of becoming trapped
despite reve rsing function
In particular, there ve rsing function will not
re act:
R tosoft, light and thin objects, e.g. fingers
R when you close thero ller sunblind again
manually immediately af ter automatic
re ve rsing #
When closing thero ller sunblind, make
sure that no body parts are in thera nge
of mo vement. #
Release the button immediately if some‐
body becomes trapped.
or #
Press the button in any direction during
th e automatic closing process.
The closing process will be stopped. Opening and closing
roller sunblinds Opening and closing
65
Yo
u can close thero ller sunblinds only when the
sliding sunroof is closed. #
Toopen: pressthe0057 button.
The roller sunblinds will open, and the sliding
sunroof will then be raised into theve nt posi‐
tion.
or #
Pull ba ckthe0057 button.
The roller sunblinds will open. #
Toclose: pull down the0057 button.
When the sliding sunroof is closed, thero ller
sunblinds will close.
If yo u push or pull the0057 button be yond the
point of resis tance and release it, you will start
automatic operation in the direction in question.
Yo u can stop automatic operation bypushing or
pulling the button again.
Opening and closing roller sunblinds from the
re ar #
Push or pull button 1tothe point of resist‐
ance and hold it until thero ller sunblind or
th e sliding sunroof has reached the desired
position. #
Automatic ope ration: push or pull button 1
be yond the point of resis tan ce and release it.
Wi th th e sliding sunroof, a comple teopening or
closing process will alw ays pass thro ugh "vent
position", a fixe d intermediate position. You will
need tooperate button 1twice toexe cute a
comple teopening or closing process. Re
ctifying problems with the sliding sunroof &
WARNING Risk of becoming trapped or
fa ta l injuries when closing the sliding
sunroof again
If yo u close the sliding sunroof again immedi‐
ately af ter it has been bloc ked or reset, the
sliding sunroof will close with increased or
maximum forc e. #
Make sure that no parts of the body are
in the closing area. #
Release the button immediately if some‐
body becomes trapped.
or #
Brief lypress the button in any direction
during the automatic closing process.
The closing process will be stopped. The sliding sunroof cannot be closed and
you
cannot de tect the cause.
If th e sliding sunroof is obstructed during closing
and opens again slightly: #
Immediately af terth e sliding sunroof has
been obstructed, pull the0057 button down
again tothe point of resis tance until the slid‐
ing sunroof is closed.
The sliding sunroof will be closed with
increased forc e.
If th e sliding sunroof is obstructed again and
opens again slightly: #
Immediately af terth e sliding sunroof has
been obstructed, pull the0057 button down
again tothe point of resis tance until the slid‐
ing sunroof is closed.
The sliding sunroof will be closed without the
automatic reve rsing function. Anti-theft pr
evention Fu
nction of the immobiliser The immobiliser pr
events your vehicle from being
st ar ted without the cor rect key.
The immobiliser is automatically activated when
th e ignition is switched off, and deactivated when
th e ignition is switched on.
When leaving theve hicle, alw aysta ke thekey
with you and lock theve hicle. If theke y is left
inside theve hicle, an yone can start the engine. 66
Opening and closing
Note
s onthe cor rect driver's seat position &
WARNING Risk of injury ifve hicle set‐
tings are adjus ted while theve hicle is in
motion
Yo u could lose control of theve hicle in partic‐
ular in thefo llowing situations:
R Ifyo u adjust the driver's seat, the head
re stra ints, thesteering wheel or the mir‐
ro r while theve hicle is in motion.
R Ifyo ufast enyour seat belt while theve hi‐
cle is in motion. #
Before starting the engine: adjust the
driver's seat, head restra ints, steering
wheel and mir ror in particular and fas‐
te nyo ur seat belt. Ensure
thefo llowing when adjusting steering
wheel 3, seat belt 2and driver's seat 1:
R You are sitting as faraw ay from the driver's
airbag as possible.
R You are sitting in an upright position.
R Your thighs are gently suppor tedby the seat
cushion.
R Your legs are not fully extended and you can
re ach the pedals easily.
R The back of your head is suppo rted at eye
le ve lby the middle part of the head restra int
R You can hold thesteering wheel with your
arms slightly bent.
R You can mo veyour legs without any restric‐
tions.
R You can see all of the instrument clus ter dis‐
pla yswe ll R
You ha vea good overview of the tra ffic condi‐
tions.
R Your seat belt sits snugly against your body
and passes across the cent reofyour shoul‐
der and across your hips in the pelvic area. Seats
Ad
justing the front seat mechanically &
WARNING Risk of becoming trapped if
th e seats are adjus tedby children
Children could become trapped if they adjust
th e seats, particular lywhen unat tended. #
When le aving theve hicle, alw aysta ke
th eke y with you and lock theve hicle. #
Never lea vechildren unat tended in the
ve hicle. &
WARNING Risk of injury ifve hicle set‐
tings are adjus ted while theve hicle is in
motion
Yo u could lose control of theve hicle in partic‐
ular in thefo llowing situations:
R Ifyo u adjust the driver's seat, the head
re stra ints, thesteering wheel or the mir‐
ro r while theve hicle is in motion.
R Ifyo ufast enyour seat belt while theve hi‐
cle is in motion. #
Before starting the engine: adjust the
driver's seat, head restra ints, steering
wheel and mir ror in particular and fas‐
te nyo ur seat belt. &
WARNING Risk of becoming trapped dur‐
ing seat adjustment
When you adjust a seat, you or other vehicle
occupants could become trapped, e.g. on the
seat guide rail. #
Make sure when adjusting a seat that
no one has any body parts in the sweep
of the seat. &
WARNING Risk of accident due tothe
driver's seat not being engaged
The driver's seat may mo veunexpectedly
while driving.
This could cause youto lose control of the
ve hicle. Seats and
stowage 69
#
Pull le ver1 upwards and slide the seat for‐
wa rds or back until the desired position has
been reached. #
Release le ver1 and push the seat back or
fo rw ards until you hear the seat engage.
% Fo
r front swivel seats, the le ver in position
1 is used torelease the swivel seat. The
le ve rto adjust thefo re -and-aft position is in
th efo rm of a bar in front of the seat
(/ page 74).
Ad justing the seat height #
Pull or push le ver3 repeatedly until the
desired seat height has been reached.
Ad justing the seat backrest #
Turn handwheel 4forw ards.
The seat backrest will mo vetoave rtical posi‐
tion. #
Turn handwheel 4backwards.
The seat backrest will tilt bac k.
Ad justing the seat angle #
Turn handwheel 2forw ards.
The front of the seat cushion will tilt down. #
Turn handwheel 2backwards.
The front of the seat cushion will tilt up. Ad
justing the front seat electrically &
WARNING Risk of becoming trapped if
th e seats are adjus tedby children
Children could become trapped if they adjust
th e seats, particularly when unattended. #
When leaving theve hicle, alw aysta ke
th eke y with you and lock theve hicle. #
Never lea vechildren unat tended in the
ve hicle. The seats can be adjus
ted when there is no key in
th e ignition loc k. &
WARNING Risk of injury ifve hicle set‐
tings are adjus ted while theve hicle is in
motion
Yo u could lose control of theve hicle in partic‐
ular in thefo llowing situations:
R Ifyo u adjust the driver's seat, the head
re stra ints, thesteering wheel or the mir‐
ro r while theve hicle is in motion.
R Ifyo ufast enyour seat belt while theve hi‐
cle is in motion. #
Before starting the engine: adjust the
driver's seat, head restra ints, steering
wheel and mir ror in particular and fas‐
te nyo ur seat belt. &
WARNING Risk of becoming trapped dur‐
ing seat adjustment
When you adjust a seat, you or other vehicle
occupants could become trapped, e.g. on the
seat guide rail. #
Make sure when adjusting a seat that
no one has any body parts in the sweep
of the seat. Obser
vethe saf ety no tes on "Airbags" and "Chil‐
dren in theve hicle". &
WARNING Risk of injury or death dueto
th e front seat being positioned too close
to the cockpit
The front airbags can also injure the occu‐
pants in the front of theve hicle. #
Always adjust the front seats so they
are as faraw ay as possible from the
front airbags. #
In addition, obser vethe no tes on cor‐
re ct seat adjustment. &
WARNING Risk of injury or death dueto
incor rect seat position
The seat belt will not of ferth e intended le vel
of pr otection if you ha venot mo vedth e seat
backrest toan almost vertical position.
In particular, you may slip under the seatbelt
and injure yourself. #
Adjust the seat properly before begin‐
ning your journe y. #
Always ensure that the seat backrest is
in an almost vertical position and that Seats and
stowage 71
#
Adjust the seat tothe desired position. #
Adjust theex terior mir rorto the desired posi‐
tion. #
Brief lypress memory button Vandthen
press preset position button 0037,Tor
U within thre e seconds.
An acoustic signal sounds. The settings are
st ored. #
Tocall up: press and hold preset position
button 0037,TorU untilthe seat and
th eex terior mir rors are in thestored position. Ro
tating the front seats &
WARNING Risk of injury orfatal injuries
due tothe driver's seat and front
passenger seat not being engaged
In this situation, there stra int sy stems cann ot
per form their intended pr otective function. #
Enga gethe driver's seat‑ and front
passenger seat in the direction of tra vel
before starting the engine. *
NO
TEDama getothe seats due tocolli‐
sion wi thadjacent car parts The seats can collide with adjacent car parts
when
they are rotated.
This can damage the seats. #
When rotating the seats, make sure
th ere is suf ficient clea rance. Yo
u can rotate the driver's and front passenger
seats by50° and 180°. The seats engage bo thin
and opposite tothe direction of tra vel as well as
at 50° totheex it. #
When rotating the seat, open there spective
front door in order toavoid a collision with
th e door trim. #
Adjust thesteering wheel in such a wayth at
th ere is suf ficient clea rance torotate and
adjust the driver's seat (/ page 96). #
Push le ver1 inthe direction of the ar row.
The turning device will be unloc ked. #
Rotate the seat in the desired direction. #
Ifth ere is a risk of collision with the cent re
console or the B‑pillar, pull le ver2 upwards
and mo vethe front seat forw ards or back‐
wa rds into the desired position. Then release
le ve r2. #
Inthe desired position, make sure that the
seat has engaged in the direction of rotation
and the longitudinal direction. Ad
justing armrests #
Foldthe armrest upwards more than 45° in
position 0048.
The armrest will be unlo cked. #
Foldthe armrest forw ards 0049asfar as it will
go. #
Slowly fold the armrest upwards into the
re qu ired position. #
Tofold the armrest up wards: if necessar y,
fo ld the armrest upwards more than 90° in
position 0047. Re
ar seats and rear ben chseat Note
s onthere ar seats
Yo ur vehicle may be equipped with thefo llowing
seats and bench seats in there ar compartment:
R Standard rear seat
R Luxury rear seat
R Comfort rear ben chseat
R Seat/bunk combination 74
Seats and stowage
#
Always make sure that there ar ben ch
seat is engaged as described. In order
toensure that there ar ben chseat can
securely engage, keep the seat guide rails and
anchora ges in theve hicle floor free from dirt and
fo re ign objects.
If th e indicator tab of the seat anchorage is not
re tracted into the seat anchorage, the seat is not
cor rectly engaged. Engage the seat again.
Re moving the seat/bunk combination
A seat/bunk combination may not be fitted in the
fa ce-to-face position. %
In
vehicles with a seat rail sy stem, car ryout
th ere lease, remo val and subsequent reins tal‐
lation of a rear ben chseat at the mar ked at
th e mar ked basic setting. #
If necessar y,remo vethe bed extension
(/ page 90). #
Remo vethestow age compartments
(/ page 98). #
Foldthere lease handle forth ere ar seat
anchorage 1up. #
Tilt th e seat/bunk combination forw ard using
th e upper edge of the seat backrest. #
Pull there lease handle for front seat ancho‐
ra ge s2 up. #
Hold the seat/bunk combination bythe lo wer
edge of the seat cushion. #
Foldthe seat/bunk combination forw ards
and lift it out of seat anchorages 3.Installing
the seat/bunk combination #
Hold the seat/bunk combination bythe lo wer
edge of the seat cushion. #
Place the seat/bunk combination into the
front seat anchorages 3from abo veatthe
front and allow toengage. #
Make sure that release handles for front seat
legs 2are folded underneath in the direc‐
tion of thefloor of theve hicle. #
Foldthe seat/bunk combination back into
th e seat position. #
Press there lease handle forth ere ar seat
anchorage 1down wards until the indicator
ta bs 4 have fully retracted into there ar seat
anchorages.
The rear seat anchorages of the seat/bunk com‐
bination are cor rectly engaged when the seat
anchorages engage audibly and the indicator tabs
4 onthe seat anchorages are no longer visible
and ha vefully retracted into the seat anchorages. Head
restra ints Ad
justing the head restra int mechanically &
WARNING Risk of injury ifve hicle set‐
tings are adjus ted while theve hicle is in
motion
Yo u could lose control of theve hicle in partic‐
ular in thefo llowing situations:
R Ifyo u adjust the driver's seat, the head
re stra ints, thesteering wheel or the mir‐
ro r while theve hicle is in motion.
R Ifyo ufast enyour seat belt while theve hi‐
cle is in motion. #
Before starting the engine: adjust the
driver's seat, head restra ints, steering
wheel and mir ror in particular and fas‐
te nyo ur seat belt. 92
Seats and stowage