2019 MAZDA MODEL CX-30 maintenance

Replace the tyre when this happens.
1. New tread
2. Worn tread
3. Tread wear indicator
You should replace the tyre before the
band crosses the entire tread.
▼Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling could
be affected, leading to loss of control
and an accident.
CAUTION
A wrong-sized wheel may adversely
affect:
¾Ty re
fit
¾Wheel and bearing life
¾Ground clearance
¾Snow-chain clearance
¾Speedometer calibration
¾Headlight aim
¾Bumper height
¾Tyre Pressure Monitoring System
*
NOTE
xWhen replacing a wheel, make sure
the new one is the same as the
original factory wheel in diameter,
rim width, and offset (inset/outset).
xFor details, contact an expert repairer
(we recommend an Authorised
Mazda Repairer).

Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and
flat spots.
Maintenance and Care
Owner Maintenance
*Some models.6-43

Light Bulbs
▼Light Bulbs
Front
Ty p e A
1. Vanity mirror lights*
2. Front overhead lights/Front map
lights
3. Side direction indicator lights
4. Front direction indicator lights/
Position lights
5. Running lights/Headlights (Low
beam)
6. Headlights (High/Low beam)
7. Running lights
8. Headlights (High beam)
*
9. Headlights (Wide-range low beam)*
Ty p e B
1. Vanity mirror lights*
2. Front overhead lights/Front map
lights
3. Side direction indicator lights
4. Running lights
*
5. Front direction indicator lights/
Position lights
6. Headlights (High/Low beam)
Rear
1. Luggage compartment light
2. High-mount brake light
3. Rear overhead light
4. Tail lights
*
5. Rear direction indicator lights
6. Brake lights/Tail lights
7. Tail lights (Liftgate side)
*
8. Reverse lights
9. Rear fog light*
10.Number plate lights
CAUTION
When removing the lens or lamp unit
using a flathead screwdriver, make sure
that the flathead screwdriver does not
contact the interior terminal. If the
flathead screwdriver contacts the
terminal, a short circuit may occur.
NOTE
xWhen replacing a bulb, contact an
expert repairer (we recommend an
Authorised Mazda Repairer) if
necessary.
xUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
xFor details regarding the installation
positions of the interior lights, refer
to the following:
Maintenance and Care
Owner Maintenance
6-44*Some models.

xVanity mirror lights
Refer to Vanity Mirrors on page
5-32.
xFront overhead lights/front map
lights, rear overhead light, and
luggage compartment light
Refer to Interior Lights on page
5-33.
▼Replacing Exterior Light Bulbs
The exterior lights have either LEDs or
normal bulbs.
Only the bulb for a running lights (type
B) can be replaced.
LED type
xHeadlightsxRunning lights (Type A)xPosition lightsxFront direction indicator lightsxSide direction indicator lightsxHigh-mount brake lightxRear direction indicator lightsxBrake lightsxTail lightsxReverse lightsxRear fog lightsxNumber plate lights
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an expert
repairer (we recommend an
Authorised Mazda Repairer) if the
replacement is necessary.
Bulb type
Running lights (Type B)
1. Make sure the ignition is switched
off, and the headlight switch is off.
2. If you are changing the left bulb,
start the engine, turn the steering
wheel all the way to the right, and
turn off engine. If you are changing
the right bulb, turn the steering
wheel to the left.
3. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
4. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
5. Turn the screw anticlockwise and
remove it, and then partially peel
back the mudguard.
Maintenance and Care
Owner Maintenance
6-45

6. Remove the wiring harness from
the clip.
7. Turn the socket and bulb assembly
anticlockwise and remove it.
8. Disconnect the bulb from the
socket.
9. Install the new bulb in the reverse
order of the removal procedure.
▼Replacing Interior Light Bulbs
LED type
xFront overhead lights/Front map
lights
xRear overhead lightxVanity mirror lights*
xLuggage compartment light
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an expert
repairer (we recommend an
Authorised Mazda Repairer) if the
replacement is necessary.
Fuses
▼Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate
circuit protector. If a fuse has blown,
the inside element will be melted.

If the same fuse blows again, avoid
using that system and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
▼Fuse Replacement
Replacing the fuses on the vehicle's
left side
If the electrical system does not work,
first inspect the fuses on the vehicle's
left side.

1. Make sure the ignition is switched
off, and other switches are off.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the
fuse puller provided on the fuse
Maintenance and Care
Owner Maintenance
6-46*Some models.

block located in the engine
compartment.
4. Inspect the fuse and replace it if it is
blown.
1. Normal
2. Blown

5. Insert a new fuse of the same
amperage rating , and make sure it
fits tightly. If it does not
fit tightly,
have an expert install it. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
If you have no spare fuses, borrow
one of the same rating from a
circuit not essential to vehicle
operation, such as the audio or
accessory socket circuit.
CAUTION
Always replace a fuse with a
genuine Mazda fuse or equivalent
of the same rating. Otherwise, you
may damage the electric system.
6. Reinstall the cover and make sure
that it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the
fuse block under the bonnet.
If a fuse is blown, it must be replaced.
Follow these steps:

1. Make sure the ignition is switched
off, and other switches are
off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of
the same amperage rating.
1. Normal
2. Blown

Maintenance and Care
Owner Maintenance
6-47

WARNING
Do not replace the main fuse by
yourself. Have an expert repairer
(we recommend an Authorised
Mazda Repairer) perform the
replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse
is a high current fuse. Incorrect
replacement could cause an
electrical shock or a short circuit
resulting in a fire.
4. Reinstall the cover and make sure
that it is securely installed.
Maintenance and Care
Owner Maintenance
6-48

▼Fuse Panel Description
Fuse block (Engine compartment)
No.FUSE RAT-
INGPROTECTED COMPONENT
F1ŠŠ
F2 20 A
Windscreen wiper de-icer
*
F330 A
Engine control system*
20 A/30 A
Injector*
F4 20 A
S-VT*
F5 40 A Engine control system
F6 20 A
S-VT
*
Maintenance and Care
Owner Maintenance
*Some models.6-49

No.FUSE RAT-
INGPROTECTED COMPONENT
F715 A
Fuel warmer
*
20 A
Fuel pump*
F8 15 A Engine control system
F9 15 A
Transmission control system
*
F10 15 A Engine control system
F11 7.5 A Air conditioner
F12 15 A Engine control system
F13 15 A
NOx sensor
*
F14 20 A
Front seat warmer*
F15 20 A
Headlight washer*
F16 15 A For protection of various circuits
F17ŠŠ
F18 15 A Accessory sockets
F19 60 A Power steering system
F20 15 A Headlight (LH) 1
F21 15 A Headlight (RH) 1
F22 15 A Keyless system
F23 30 A ABS, Dynamic stability control system
F24 15 A Headlight (LH) 2
F25 15 A Headlight (RH) 2
F26 7.5 A On board diagnostics
F27 25 A For protection of various circuits
F28 25 A For protection of various circuits
F29 15 A Windscreen washer
F30ŠŠ
F31 15 A Horn
F32 15 A Headlights
F33ŠŠ
F34ŠŠ
F35 50A ABS, Dynamic stability control system
F36ŠŠ
F37 40 A Rear window defogger
F38 50 A For protection of various circuits
Maintenance and Care
Owner Maintenance
6-50*Some models.