2019 MAZDA MODEL CX-30 service indicator

Scheduled Maintenance
▼Scheduled Maintenance
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system
and to efficient engine operation. Do not tamper with them.
All inspections and adjustments must be made by an expert repairer (we
recommend an Authorised Mazda Repairer).
▼Europe
Vehicles utilizing the vehicle status monitor feature (My Mazda Service):
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
For vehicles in European countries, except SKYACTIV-D 1.8 for Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
20,000 km (12,500 miles) or 12 months, whichever comes first. (after the previous
maintenance)
For SKYACTIV-D 1.8 vehicles in Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
10,000 km (6,250 miles) or 12 months, whichever comes
first. (after the previous
maintenance)
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
SKYACTIV-G 2.0 AND SKYACTIV-X 2.0
Engine oil &
filter
*1*2RRRRRRRRRRRR
Spark plugs
*4
SKYACTIV-G
2.0Replace every 120,000 km (75,000 miles).
SKYACTIV-X
2.0Replace every 64,000 km (40,000 miles).
Air filter
*5RRRR
Fuel lines and hoses IIIIII
Hoses and tubes for emission I I I I
SKYACTIV-D 1.8
Engine oil &
filter
*1*3RRRRRRRRRRRR
Maintenance and Care
Scheduled Maintenance
6-3

*10 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the
vehicle is operated in extremely humid climates, replace the brake fluid annually.
*11 If this component has been submerged in water, the oil should be replaced.*12 Tyre rotation is recommended every 10,000 km (6,250 miles).*13 Inspect a spare tyre if installed.*14 Check the tyre repair fluid expiration date every year when performing the periodic maintenance.
Replace the tyre repair fluid bottle with new one before the expiration date.
*15 If DTC P1200 is stored, clean the fuel system by Mazda genuine deposit cleaner.
If the required tool (M-MDS) is not available, clean the fuel system by Mazda genuine deposit
cleaner without performing self-test.
Using non-genuine deposit cleaner would cause an internal failure in the fuel system.
*16 If the vehicle is operated primarily under any of the following conditions, perform "Self-test with
Mazda Modular Diagnostic System (M-MDS)" at every 10,000 km (6,250 miles).
a) The vehicle is idled for long periods or driven at low speeds, such as with police cars, taxis, or
driver's education school car.
b) Driving under extremely high temperature conditions.
▼Except Europe
Israel
Vehicles utilizing the vehicle status monitor feature:
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.

Maximum interval 15,000 km or 12 months, whichever comes first

Manually set Next Service Distance of Vehicle Status Monitor to 10,000 km or short-
er if the vehicle is driven primarily under any of the following conditions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Maintenance Item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Engine oil & oil
filter *1RRRRRRRRRRRR
Drive belts
*2IIIIIIIIIIII
Engine coolant level IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-6

Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
10,000 km or shorter.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level,
specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.*7 Check the tyre repair fluid expiration date every year when performing the periodic maintenance.
Replace the tyre repair
fluid bottle with new one before the expiration date.
*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the
vehicle is driven in extremely humid climates, replace the brake fluid annually.
*9 If the vehicle is driven in very dusty or sandy areas, clean and if necessary, replace the air
filter more
often than the recommended intervals.
*10 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22
may cause serious damage to the engine and cooling system.
Russia/Belarus/Azerbaijan/Kazakhstan/Armenia
Vehicles utilizing the vehicle status monitor feature:
Russia/Belarus/Kazakhstan
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.
Refer to Table A to identify the required maintenance items.

Maximum interval 15,000 km or 12 months, whichever comes first

Manually set Next Service Distance and Date of Vehicle Status Monitor to 7,500 km
and 6 months if the vehicle is driven primarily under any of the following conditions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Maintenance and Care
Scheduled Maintenance
6-8

Refer to Table B to identify the required maintenance items.
Azerbaijan/Armenia
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.
Refer to Table B to identify the required maintenance items.

Maximum interval 5,000 km or 6 months, whichever comes
first

Manually set Next Service Distance of Vehicle Status Monitor to a shorter mileage
than 5,000 km if the vehicle is driven primarily under any of the following condi-
tions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Refer to Table B to identify the required maintenance items.
Ta b l e A
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Engine oil &
filter *1RRRRRRRRRRRR
Spark plug IIIIIIIRIIII
Drive belts
*2IIIIIIIIIIII
Engine coolant level IIIIIIIIIIII
Battery
*3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Steering operation and linkages I I I I I I I I I I I I
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Driveshaft dust boot IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-9

Display*1*2Content Action to be taken
Depress Brake Pedal to
Start EngineThis message is indicated when the
push button start is pressed without
depressing the brake pedal.When starting the engine, press the
push button start with the brake ped-
al depressed.
Depress Clutch Pedal to
Start EngineThis message is indicated when the
push button start is pressed without
depressing the clutch pedal.When starting the engine, press the
push button start with the clutch
pedal depressed.
Press Push Button Start
Switch While Turning
Steering Wheel Left or
RightThis message is indicated while the
steering wheel is locked.Release the steering wheel lock by
pressing the start button while turn-
ing the steering wheel to the left and
right.
Check Gear Selector
Lever PositionThis message is indicated when the
selector lever is shifted to the P or R
position while driving.Check the selector lever position.
Close Door and Fasten
Seat BeltThis message is indicated when AU-
TOHOLD is about to operate and a
door is opened or a seat belt is unfas-
tened.When the AUTOHOLD is turned on,
close the doors and fasten seat belts.
Wiper Blades Must Be
on Windscreen Before
OperatingThis message is indicated when the
ignition is switched ON with the wip-
er arms at the service positions.Return the wiper arms to the initial
positions.
Windscreen Wiper
Range of Motion Re-
duced. Remove Ob-
struction(s)This message is indicated when there
is snow or dirt accumulation on the
windscreen and the wiper operation
range is narrowed.Remove foreign matter from the
windscreen.
Ignition Not Switched
OffThis message is indicated when the
driver’s door is opened without
switching the ignition OFF.Switch the ignition OFF before leaving
the vehicle.
Gear Selector Lever Not
in ParkDisplays when the push button start
is pressed while the selector lever is
in a position other than P, and the ig-
nition is switched to ACC.Shift the selector lever to the P posi-
tion and then switch the ignition OFF.
Excessive Transmission
Temperature. Drive
SlowlyThis message is indicated when the
internal temperature of the automatic
transmission is high.Drive slowly to reduce load on the
automatic transmission.
Excessive Transmission
Temperature. Stop Vehi-
cle in a safe LocationThis message is indicated when the
automatic transmission
fluid temper-
ature is abnormally high.Park the vehicle in a safe place imme-
diately and contact an expert repairer
(we recommend an Authorised Maz-
da Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-65

where contact details are also
provided.

Data, which is exclusively stored locally
on the vehicle, may be viewed with
expert assistance, e.g., in a vehicle
workshop, in return for payment if
appropriate.

Legal requirements regarding the
disclosure of data
To the extent that legal regulations
exist, manufacturers are obliged to
release information stored by them, at
the request of public authorities, to the
extent required on a case-by-case
basis (e.g., when a criminal offence is
being investigated).

Public authorities are also permitted to
read the data from vehicles in specific
cases, within the scope of applicable
law. For example, in the event of an
accident, information can be read from
the air bag control unit to help clarify
the circumstances of the accident.

Operational data on the vehicle
Control units process data in order to
operate the vehicle.

These include, for example:
xvehicle status information (e.g.,
speed, deceleration, lateral
acceleration, wheel speed, seatbelt
usage indicator),
xenvironmental conditions (e.g.,
temperature, rain sensor, distance
sensor).

These data are generally volatile and
are not stored beyond the operating
time, and only processed on the
vehicle itself. Control units frequently
contain data storage media. These can
be used to document, either
temporarily or permanently,
information about the condition of the
vehicle, component stress,
maintenance requirements and
technical events and failures.

The following information may be
stored, depending on the technical
configuration:
xoperating conditions of system
components (e.g.,
fill levels, tyre
pressures and battery status),
xmalfunctions and defects in
important system components (e.g.,
lighting and brakes),
xresponse of the system to
extraordinary driving situations (e.g.,
deployment of an air bag, activation
of stability control systems),
xinformation on events in which the
vehicle is damaged,
xfor electric vehicles, the state of
charge of the high-voltage battery
and the vehicle’s estimated range.

In particular cases (e.g., if the vehicle
has detected a malfunction), it may be
necessary to store data which would
normally be volatile.

If you make use of services (e.g., repair
and maintenance services), it may be
possible, if necessary, to read out and
use the stored operating data together
with the vehicle identification number.
The data from the vehicle may be read
out by employees of the Mazda
Network (e.g. authorised workshops,
manufacturer) or by third parties (e.g.,
breakdown services, independent
repair shops). The same applies in the
case of warranty cases and quality
assurance measures.

The data is usually read out via the
mandatory OBD (on-board
Customer Information
Collection and Processing of Data in the Vehicle
8-6