2019 MAZDA MODEL CX-30 warning lights

Front Passenger Air Bag Deactivation Switch*
▼Front Passenger Air Bag Deactivation Switch
WARNING
Do not deactivate the front passenger air bag unnecessarily:
Unnecessary deactivation of the front passenger air bag is dangerous. If turned
off
unnecessarily, the front passenger will not receive the added protection of the air
bag. Serious injuries or even death could occur. With the exception of installing a
child-restraint system on the front passenger seat, do not turn the air bag
deactivation switch to the OFF position.

The front passenger air bag deactivation switch should be used to deactivate the
front passenger front and side air bags and also the front passenger seat belt
pretensioner system if installing a child-restraint system on the front passenger seat.
When the ignition is switched ON, both front passenger air bag deactivation
indicator lights illuminate regardless of the front passenger air bag deactivation
switch position. The indicator light turns off after a specified period of time, then
turns on/off depending on the conditions as indicated in the following table.

Front Passenger Air Bag Deacti-
vation SwitchFront Passenger Seat/Side Air
Bag, Front Passenger Seat Belt
Pretensioner Operation Condi-
tionFront Passenger Air Bag Deacti-
vation Indicator Light
OFF position
Deactivate
Essential Safety Equipment
SRS Air Bags
*Some models.2-51

Keyless Entry System
▼Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors,
liftgate, and fuel-filler flap, and opens/
closes the liftgate.
The system can start the engine
without having to take the key out of
your purse or pocket.
Operating the theft-deterrent system is
also possible on theft-deterrent
system-equipped vehicles.

System malfunctions or warnings are
indicated by the following warning
lights or beeps.
Check the displayed message for more
information and, if necessary, have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer), according to the indication.
xKEY Warning Indication/Warning
Light (Red)
Refer to KEY Warning Indication/
Warning Light (Red) on page 7-56.
xIgnition Not Switched Off (STOP)
Warning Beep
Refer to Ignition Not Switched Off
(STOP) Warning Beep on page
7-67.
xKey Removed from Vehicle Warning
Beep
Refer to Key Removed from Vehicle
Warning Beep on page 7-68.
If you have a problem with the key,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).

If your key is lost or stolen, consult an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible for a replacement and to
make the lost or stolen key inoperative.
CAUTION
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
NOTE
xThe keyless entry system operation
may vary due to local conditions.
xThe keyless entry system is fully
operational when the ignition is
switched off. The system does not
operate if the ignition is switched to
any position other than off.
xIf the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new
battery, refer to Key Battery
Replacement (page 6-39).
xBattery life is about 1 year. Replace
the battery with a new one if the
messages are displayed in the
instrument cluster. Replacing the
battery about once a year is
recommended because the KEY
warning indication may not display
depending on the rate of battery
depletion.
xAdditional keys can be obtained at
an Authorised Mazda Repairer. Up
to 6 keys can be used with the
keyless functions per vehicle. Bring
all keys to an Authorised Mazda
Repairer when additional keys are
required.
Before Driving
Keys
3-4

▼Transmitter
1. Operation indicator light
2. Lock button (
)
3. Unlock button (
)
4. Power liftgate button (
or )*
5. Intrusion sensor cancel button ()*
NOTE
xThe headlights turn on/off by
operating the transmitter. Refer to
Leaving Home Light on page 4-57.
x(With theft-deterrent system)
The hazard warning lights
flash when
the theft-deterrent system is armed
or turned
off.
Refer to Theft-Deterrent System on
page 3-49.
x(With the advanced keyless function
(European models))
The setting can be changed so that a
beep sound is heard for confirmation
when the doors, liftgate, and
fuel-filler flap are locked/unlocked
using the key.
(With the advanced keyless function
(Except European models))
A beep sound can be heard for
confirmation when the doors,
liftgate, and
fuel-filler
flap are
locked/unlocked using the key. If
you prefer, the beep sound can be
turned
off.
The volume of the beep sound can
also be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
The operation indicator light
flashes
when the buttons are pressed.
Lock button
To lock the doors, liftgate, and
fuel-filler flap, press the lock button
and the hazard warning lights will
flash
once.
(With the advanced keyless function
(Except European models))
A beep sound will be heard once.
NOTE
xIf the lock button is pressed with any
door or liftgate open, any closed
door can be locked. Close any open
door and liftgate to lock.
xMake sure all the doors, liftgate, and
fuel-filler flap are locked after
pressing the button.
x(With double locking system)
Pressing the lock button twice within
3 seconds will activate the double
locking system.
Refer to Double Locking System on
page 3-12.
x(With theft-deterrent system)
If the lock button is pressed with all
the doors and liftgate closed, the
hazard warning lights will flash and
the theft-deterrent system is armed.
Unlock button
Ty p e A
To unlock the driver's door and the
fuel-filler flap, press the unlock button
and the hazard warning lights will flash
twice.
Before Driving
Keys
*Some models.3-5

(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.

To unlock the other doors and liftgate,
press the unlock button again within 5
seconds.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.
Ty p e B
To unlock the doors, liftgate, and
fuel-filler flap, press the unlock button
and the hazard warning lights will
flash
twice.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.
NOTE
x(With 2-step unlocking function)
xThe system can be set to unlock all
the doors, liftgate, and fuel-filler
flap when pressing the unlock
button once.
xThe system can be set to unlock
the driver's door and the fuel-filler
flap by pressing the unlock button
on the transmitter, and to unlock
the other doors and liftgate by
pressing the button again within 5
seconds.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(Auto re-lock function)
After unlocking with the key, all the
doors, liftgate, and fuel-filler flap will
automatically lock if any of the
following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
flash for confirmation.
xA door or the liftgate is opened.xThe ignition is switched to any
position other than
off.
The time required for the doors to
lock automatically can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(With theft-deterrent system)
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned
off, the hazard
warning lights will flash twice to
indicate that the system is turned
off.
Power liftgate button
*
To open/close the liftgate, press the
power liftgate button for one second
or longer with the liftgate in the fully
closed/open position.
The hazard warning lights flash twice
and the liftgate opens/closes after the
beep sounds.
For details on the power liftgate
function, refer to Power Liftgate on
page 3-22.
Ty p e A
Ty p e B
Before Driving
Keys
3-6*Some models.

Intrusion sensor cancel button*
To cancel the intrusion sensor (part of
the theft-deterrent system), press the
intrusion sensor cancel button within
20 seconds after pressing the lock
button and the hazard warning lights
will flash 3 times.
Refer to Theft-Deterrent System on
page 3-49.
Power saving function
By turning on the transmitter power
saving function, the advanced keyless
entry
*1 and push button start system
functions turn off and the battery
power consumption of the transmitter
is restricted.
The remote control function is
operational by operating the
transmitter switch even while the
power saving function is turned on.
However, the operation indicator light
of the transmitter does not turn on/
flash.
Turning on the power saving function
After you have turned on the power
saving function according to the
following procedure, the hazard
warning lights and sound operate
*1
one time.
1. Press the lock button on the
transmitter 4 times within 3
seconds to turn on the operation
indicator light.
2. Press the lock button continuously
for 1.5 seconds or longer while the
operation indicator light turns on
(for 5 seconds).
3. Press any of the buttons on the
transmitter to make sure that the
operation indicator light does not
turn on/flash.
Turning
off the power saving function
After you have turned off the power
saving function according to the
following procedure, the hazard
warning lights and sound operate
*1
one time.
1. Press any of the buttons on the
transmitter to make sure that the
operation indicator light does not
turn
on/flash.
2. Press the lock button on the
transmitter 4 times within 3
seconds to turn on the operation
indicator light.
3. Press the lock button continuously
for 1.5 seconds or longer while the
operation indicator light turns on
(for 5 seconds).
*1 With the advanced keyless function
▼Operational Range
The system operates only when the
driver is in the vehicle or within
operational range while the key is
being carried.
Starting the Engine
NOTE
xStarting the engine may be possible
even if the key is outside of the
vehicle and extremely close to a door
and window, however, always start
the engine from the driver's seat.
If the vehicle is started and the key is
not in the vehicle, the vehicle will not
restart after it is shut off and the
ignition is switched to off.
Before Driving
Keys
*Some models.3-7

WARNING
Never activate the double locking
system with passengers, especially
children, still inside the vehicle:
Activating the system with passengers,
especially children, still inside the
vehicle is dangerous. The passengers
cannot open the doors from inside.
They would be trapped and subjected
to extreme temperatures. This could
result in serious injuries or even death.
How to Activate the system
1. Switch the ignition
off and take the
key with you.
2. Close all the doors and liftgate.
3. Press the lock button on the
transmitter twice within 3 seconds.
The hazard warning lights operate 1
time each time the button is
pressed.
NOTE
x(With the advanced keyless
function)
You can also activate the system
by touching the sensing area of
the door lock touch sensor twice
within 3 seconds. The hazard
warning lights operate 1 time
each time the sensing area is
touched.
4. The indicator light illuminates for
about 3 seconds to indicate that
the system has been activated.

NOTE
The system cannot be activated
when any door or the liftgate is
open.
How to Deactivate the System
Unlock the driver's door or start the
engine.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the system can only be deactivated by
unlocking a door with the auxiliary key.
▼Locking, Unlocking with Touch
Sensor, Door Handle (With the
advanced keyless function)
By touching the sensing area of the
touch sensor, various locking/
unlocking operations can be done
without taking the key out of a bag or
pocket.
There are two types of touch sensors
used for locking and unlocking , and
each sensor is built into the outer door
handle on the driver and front
passenger's doors.
1. Sensing area of door lock touch
sensor (Depression on outer side of
door handle)
2. Sensing area of door release touch
sensor (Inner side of door handle)
NOTE
xWhen locking/unlocking with the
transmitter carried, securely touch
the sensing area of the touch sensor
as follows.
Before Driving
Doors and Locks
3-13

Locking
Unlocking
xThe system may not operate normally
under the following conditions.
xYou touch the sensing area of the
door lock touch sensor and the
sensing area of the door release
touch sensor at the same time.
xYou touch the sensing area of the
touch sensor while wearing gloves.
xForeign matter such as snow or dirt
is stuck on the sensing area of the
touch sensor.
xYou pull the door handle just after
touching the sensing area of the
touch sensor.
xThe system may operate if the outer
side door handle of a front door is
splashed with water by a car wash or
rain while the transmitter is in the
operation range.
xIf the system does not operate even
though you touch the sensing area of
the touch sensor correctly, release
the touch sensor once, and then
touch the sensing area of the touch
sensor again after waiting about 3
seconds.
Locking
When locking , touch the sensing area
of the door lock touch sensor with all
of the following conditions met.
xThe ignition is switched OFF.xAll the doors are closed.xYou are carrying the transmitter.
The following locations are locked by
touching the sensing area of the door
lock touch sensor.
xAll doorsxFuel-filler flapxLiftgate
When locking , the hazard warning
lights operate one time.
(Except European models)
A beep sound operate one time.
Unlocking
When unlocking , touch the sensing
area of the door release touch sensor
with all of the following conditions
met.
xThe ignition is switched OFF.xThe driver’s door is locked.xThree seconds or longer have passed
since the doors were locked.
xYou are carrying the transmitter.
Ty p e A
(Unlocking from the driver's door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the
driver's door.
Before Driving
Doors and Locks
3-14

xDriver’s doorxFuel-filler flap
NOTE
xThe location to be unlocked can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.

(Unlocking from the front passenger’s
door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the front
passenger's door.
xAll doorsxFuel-filler flapxLiftgate
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.
Ty p e B
The following locations are unlocked
by touching the sensing area of the
door release touch sensor.
xAll doorsxFuel-filler flapxLiftgate
NOTE
x(With 2-step unlocking function)
The location to be unlocked can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.
NOTE
xConfirm that all the doors and
liftgate are securely locked.
For the liftgate, move it without
pressing the electric liftgate opener
to verify that the liftgate has not been
left ajar.
x(European models)
The setting can be changed so that a
beep sound is heard for confirmation
when the doors, fuel-filler flap, and
liftgate are locked/unlocked using a
touch sensor.
(Except European models)
A beep sound is heard for
confirmation when the doors,
fuel-filler flap, and liftgate are
locked/unlocked using the touch
sensor. If you prefer, the beep sound
can be turned off.
The volume of the beep sound can
also be changed. Refer to the
Settings section in the Mazda
Connect Owner's Manual.
x(With theft-deterrent system)
The hazard warning lights flash when
the theft-deterrent system is armed
or turned off.
Refer to Theft-Deterrent System on
page 3-49.
xThe setting can be changed so that
the doors, fuel-filler flap, and liftgate
are locked automatically without
touching the sensing area of the
touch sensor.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
(Walk-away auto lock function)
Before Driving
Doors and Locks
3-15