2019 MAZDA MODEL CX-30 sound

2. Adjust the steering wheel height so
that the gauges can be viewed
easily.
3. Raise the lever to securely lock the
steering wheel.
Adjusting the head restraint position
To prevent shock to the head and
neck, adjust the head restraints to their
correct positions.
Refer to Height Adjustment on page
2-15.
▼Driving Position Memory (Power
Seat)*
The desired driving position can be
called up after programming the
position.
The following driving positions can be
programmed.
xDriver’s seat position (seat slide,
height adjustment, front edge of seat
bottom, seat recline)
Refer to Adjusting the Driver's Seat
on page 2-4.
xActive driving display (display
position, brightness level, display
information)
Refer to Active Driving Display on
page 4-39.
xOutside mirror angle
Refer to Outside Mirrors on page
3-36.
A driving position can be programmed
to the following parts.
xPosition memory button
xTransmitter used for vehicle
NOTE
xLumbar support adjustment cannot
be programmed.
Programming
1. Make sure the parking brake is on.
2.(Automatic transmission)
Make sure the selector lever is in
the P position.
3. Switch the ignition ON.
4. Adjust the following parts to the
desired conditions.
xDriver's seatxActive driving displayxOutside mirrors
5. Press the SET button continuously
until a sound is activated.
1. 1 button
2. 2 button
3. SET button
6. Do the following operation within 5
seconds after the sound is activated
to programme the driving position.
xProgramming to a position
memory button
Press the button you want to
programme, either 1 or 2 button.
xProgramming to the transmitter
Press the unlock button on the
transmitter.
A sound is activated when the
operation is completed correctly.
Essential Safety Equipment
Seats
2-10*Some models.

NOTE
xIf you do not perform the operation
correctly, a sound indicating that the
programming has failed is activated.
xIf the angle of the outer mirrors only
changes a little, the angle of the
outer mirrors may not have been
programmed correctly.
xIf the angle of the outer mirrors is
adjusted close to the limits of its
range of motion, the driving position
can be successfully programmed, but
it may fail when calling up the
programmed driving position.
Calling up the programmed driving
position
CAUTION
Do not place fingers or hands around
the bottom of the seat while the seat
memory function is operating. The seat
moves automatically while the seat
memory function is operating and
fingers or hands could get pinched and
injured.
Using the position memory button
1. Make sure the parking brake is on.
2.(Automatic transmission)
Make sure the selector lever is in
the P position.
3. Switch the ignition ON.
4. Press the programming button for
the driving position you want to call
up (button 1 or 2).
5. A sound is activated when the
adjustment to the programmed
driving position is completed.
NOTE
xWhen adjustment of the driving
position is not necessary, a sound is
not activated.
xThe driving position adjustment is
cancelled in the following cases:
xThe seat adjustment switch on the
driver's seat is operated.
xThe angle of the outer mirrors is
adjusted.
xThe SET button is pressed.xProgramming button 1 or 2 is
pressed.
xThe lock button or unlock button
on the transmitter is pressed.
xThe vehicle starts moving.xThe active driving display is
adjusted.
x(Manual transmission)
The parking brake is released.
x(Automatic transmission)
The selector lever is shifted to a
position other than P.
Using the transmitter
1. Unlock the driver's door using one
of the following methods.
xTouch the sensing area of the
door release touch sensor.
xPress the unlock button on the
transmitter.
2. When you open the driver's door
within 90 seconds after unlocking
the doors, the adjustment of the
following parts starts.
xDriver's seatxActive driving display (When the
ignition is switched ON, the
adjusted active driving display is
activated.)
xOutside mirrors
A sound is activated when the
adjustment is completed.
NOTE
xWhen adjustment of the driving
position is not necessary, a sound is
not activated.
Essential Safety Equipment
Seats
2-11

xThe driving position adjustment is
cancelled in the following cases:
xThe seat adjustment switch on the
driver's seat is operated.
xThe angle of the outer mirrors is
adjusted.
xThe SET button is pressed.xProgramming button 1 or 2 is
pressed.
xThe lock button or unlock button
on the transmitter is pressed.
xThe vehicle starts moving.xThe active driving display is
adjusted.
x(Manual transmission)
The parking brake is released.
x(Automatic transmission)
The selector lever is shifted to a
position other than P.
Erasing programmed driving positions
Erasing the driving positions
programmed to the key
1. Switch the ignition OFF.
2. Press the SET button continuously
until a sound is activated.
3. Press the lock button on the
transmitter within 5 seconds after
the sound is activated.
NOTE
If you do not perform the operation
correctly, a sound indicating that the
programming has failed is activated.
▼Adjusting the Front Passenger's
Seat
1.Seat Slide
To move a seat forward or
backward, raise the lever and slide
the seat to the desired position and
release the lever.
Make sure the lever returns to its
original position and the seat is
locked in place by attempting to
push it forward and backward.
2.Height Adjustment
*
To adjust the seat height, move the
lever up or down.
3.Seat Recline
To change the seatback angle, lean
forward slightly while raising the
lever. Then lean back to the desired
position and release the lever.
Make sure the lever returns to its
original position and the seatback is
locked in place by attempting to
push it forward and backward.

Essential Safety Equipment
Seats
2-12*Some models.

▼Transmitter
1. Operation indicator light
2. Lock button (
)
3. Unlock button (
)
4. Power liftgate button (
or )*
5. Intrusion sensor cancel button ()*
NOTE
xThe headlights turn on/off by
operating the transmitter. Refer to
Leaving Home Light on page 4-57.
x(With theft-deterrent system)
The hazard warning lights
flash when
the theft-deterrent system is armed
or turned
off.
Refer to Theft-Deterrent System on
page 3-49.
x(With the advanced keyless function
(European models))
The setting can be changed so that a
beep sound is heard for confirmation
when the doors, liftgate, and
fuel-filler flap are locked/unlocked
using the key.
(With the advanced keyless function
(Except European models))
A beep sound can be heard for
confirmation when the doors,
liftgate, and
fuel-filler
flap are
locked/unlocked using the key. If
you prefer, the beep sound can be
turned
off.
The volume of the beep sound can
also be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
The operation indicator light
flashes
when the buttons are pressed.
Lock button
To lock the doors, liftgate, and
fuel-filler flap, press the lock button
and the hazard warning lights will
flash
once.
(With the advanced keyless function
(Except European models))
A beep sound will be heard once.
NOTE
xIf the lock button is pressed with any
door or liftgate open, any closed
door can be locked. Close any open
door and liftgate to lock.
xMake sure all the doors, liftgate, and
fuel-filler flap are locked after
pressing the button.
x(With double locking system)
Pressing the lock button twice within
3 seconds will activate the double
locking system.
Refer to Double Locking System on
page 3-12.
x(With theft-deterrent system)
If the lock button is pressed with all
the doors and liftgate closed, the
hazard warning lights will flash and
the theft-deterrent system is armed.
Unlock button
Ty p e A
To unlock the driver's door and the
fuel-filler flap, press the unlock button
and the hazard warning lights will flash
twice.
Before Driving
Keys
*Some models.3-5

(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.

To unlock the other doors and liftgate,
press the unlock button again within 5
seconds.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.
Ty p e B
To unlock the doors, liftgate, and
fuel-filler flap, press the unlock button
and the hazard warning lights will
flash
twice.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.
NOTE
x(With 2-step unlocking function)
xThe system can be set to unlock all
the doors, liftgate, and fuel-filler
flap when pressing the unlock
button once.
xThe system can be set to unlock
the driver's door and the fuel-filler
flap by pressing the unlock button
on the transmitter, and to unlock
the other doors and liftgate by
pressing the button again within 5
seconds.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(Auto re-lock function)
After unlocking with the key, all the
doors, liftgate, and fuel-filler flap will
automatically lock if any of the
following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
flash for confirmation.
xA door or the liftgate is opened.xThe ignition is switched to any
position other than
off.
The time required for the doors to
lock automatically can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(With theft-deterrent system)
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned
off, the hazard
warning lights will flash twice to
indicate that the system is turned
off.
Power liftgate button
*
To open/close the liftgate, press the
power liftgate button for one second
or longer with the liftgate in the fully
closed/open position.
The hazard warning lights flash twice
and the liftgate opens/closes after the
beep sounds.
For details on the power liftgate
function, refer to Power Liftgate on
page 3-22.
Ty p e A
Ty p e B
Before Driving
Keys
3-6*Some models.

Intrusion sensor cancel button*
To cancel the intrusion sensor (part of
the theft-deterrent system), press the
intrusion sensor cancel button within
20 seconds after pressing the lock
button and the hazard warning lights
will flash 3 times.
Refer to Theft-Deterrent System on
page 3-49.
Power saving function
By turning on the transmitter power
saving function, the advanced keyless
entry
*1 and push button start system
functions turn off and the battery
power consumption of the transmitter
is restricted.
The remote control function is
operational by operating the
transmitter switch even while the
power saving function is turned on.
However, the operation indicator light
of the transmitter does not turn on/
flash.
Turning on the power saving function
After you have turned on the power
saving function according to the
following procedure, the hazard
warning lights and sound operate
*1
one time.
1. Press the lock button on the
transmitter 4 times within 3
seconds to turn on the operation
indicator light.
2. Press the lock button continuously
for 1.5 seconds or longer while the
operation indicator light turns on
(for 5 seconds).
3. Press any of the buttons on the
transmitter to make sure that the
operation indicator light does not
turn on/flash.
Turning
off the power saving function
After you have turned off the power
saving function according to the
following procedure, the hazard
warning lights and sound operate
*1
one time.
1. Press any of the buttons on the
transmitter to make sure that the
operation indicator light does not
turn
on/flash.
2. Press the lock button on the
transmitter 4 times within 3
seconds to turn on the operation
indicator light.
3. Press the lock button continuously
for 1.5 seconds or longer while the
operation indicator light turns on
(for 5 seconds).
*1 With the advanced keyless function
▼Operational Range
The system operates only when the
driver is in the vehicle or within
operational range while the key is
being carried.
Starting the Engine
NOTE
xStarting the engine may be possible
even if the key is outside of the
vehicle and extremely close to a door
and window, however, always start
the engine from the driver's seat.
If the vehicle is started and the key is
not in the vehicle, the vehicle will not
restart after it is shut off and the
ignition is switched to off.
Before Driving
Keys
*Some models.3-7

All doors, fuel-filler flap, and liftgate
will automatically unlock if they are
locked using the power door locks
with any door or the liftgate open.
The vehicle lock-out prevention
feature does not operate while the
ignition is switched off.
When all doors, fuel-filler flap, and
liftgate are locked using the power
door lock with any door or the
liftgate open, the closed doors,
fuel-filler flap, and liftgate are
locked. After that, when all doors
and the liftgate are closed, all doors
and the liftgate are locked. However,
if the key is inside the vehicle, all
doors, fuel-filler flap, and liftgate are
automatically unlocked.
(With the advanced keyless
function)
The beep sound is heard for about
10 seconds to notify the driver that
the key has been left in the vehicle.
(Without the advanced keyless
function)
The horn sound is heard twice to
notify the driver that the key has
been left in the vehicle.
x(Door unlock (control) system with
collision detection)
This system automatically unlocks the
doors, fuel-filler flap, and liftgate in
the event the vehicle is involved in an
accident to allow passengers to get
out of the vehicle immediately and
prevent being trapped inside. While
the ignition is switched ON and in
the event the vehicle receives an
impact strong enough to inflate the
air bags, all the doors,
fuel-filler
flap,
and liftgate are automatically
unlocked after about 6 seconds have
elapsed from the time of the
accident.
The doors, fuel-filler flap, and liftgate
may not unlock depending on how
an impact is applied, the force of the
impact, and other conditions of the
accident.
If door-related systems or the battery
is malfunctioning , the doors and
the , fuel-filler flap, and liftgate may
not unlock depending on your
vehicle type.
▼Unlocking with Auxiliary Key
Only the driver's door can be unlocked
using the auxiliary key.
Refer to Keys on page 3-2.
Insert the auxiliary key while the
driver's door handle is pulled and turn
the key to the unlock side. Turn the
auxiliary key back to its original
position before removing it.
NOTE
If you attempt to open the driver’s
door using an unauthorised auxiliary
key, the key cylinder will spin around
but the door will not unlock.
▼Double Locking System*
The double locking system is designed
to prevent someone who has broken
into your vehicle from opening the
door from the inside.

If you have any problems with the
double locking system, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
Before Driving
Doors and Locks
3-12*Some models.

Locking
Unlocking
xThe system may not operate normally
under the following conditions.
xYou touch the sensing area of the
door lock touch sensor and the
sensing area of the door release
touch sensor at the same time.
xYou touch the sensing area of the
touch sensor while wearing gloves.
xForeign matter such as snow or dirt
is stuck on the sensing area of the
touch sensor.
xYou pull the door handle just after
touching the sensing area of the
touch sensor.
xThe system may operate if the outer
side door handle of a front door is
splashed with water by a car wash or
rain while the transmitter is in the
operation range.
xIf the system does not operate even
though you touch the sensing area of
the touch sensor correctly, release
the touch sensor once, and then
touch the sensing area of the touch
sensor again after waiting about 3
seconds.
Locking
When locking , touch the sensing area
of the door lock touch sensor with all
of the following conditions met.
xThe ignition is switched OFF.xAll the doors are closed.xYou are carrying the transmitter.
The following locations are locked by
touching the sensing area of the door
lock touch sensor.
xAll doorsxFuel-filler flapxLiftgate
When locking , the hazard warning
lights operate one time.
(Except European models)
A beep sound operate one time.
Unlocking
When unlocking , touch the sensing
area of the door release touch sensor
with all of the following conditions
met.
xThe ignition is switched OFF.xThe driver’s door is locked.xThree seconds or longer have passed
since the doors were locked.
xYou are carrying the transmitter.
Ty p e A
(Unlocking from the driver's door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the
driver's door.
Before Driving
Doors and Locks
3-14