2019 MAZDA MODEL CX-30 cooling

▼Engine Exhaust (Carbon
monoxide)
WARNING
Do not drive your vehicle if you smell
exhaust gas inside the vehicle:
Engine exhaust gas is dangerous. This
gas contains carbon monoxide (CO),
which is colourless, odourless, and
poisonous. When inhaled, it can cause
loss of consciousness and death. If you
smell exhaust gas inside the vehicle,
keep all windows fully open and
contact an expert repairer (we
recommend an Authorised Mazda
Repairer) immediately.
Do not run the engine when inside an
enclosed area:
Running the engine inside an enclosed
area, such as a garage, is dangerous.
Exhaust gas, which contains poisonous
carbon monoxide, could easily enter
the cabin. Loss of consciousness or
even death could occur.
Open the windows or adjust the
heating or cooling system to draw
fresh air when idling the engine:
Exhaust gas is dangerous. When the
vehicle is stopped with the windows
closed and the engine running for a
long time even in an open area,
exhaust gas, which contains poisonous
carbon monoxide, could enter the
cabin. Loss of consciousness or even
death could occur.
Clear snow from underneath and
around your vehicle, particularly the
tail pipe, before starting the engine:
Running the engine when a vehicle is
stopped in deep snow is dangerous.
The exhaust pipe could be blocked by
the snow, allowing exhaust gas to
enter the cabin. Because exhaust gas
contains poisonous carbon monoxide,
it could cause loss of consciousness or
even death to occupants in the cabin.
Before Driving
Fuel and Emission
3-33

NOTE
xThe cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or
off, to cool the engine
compartment quickly.
xIf the system detects that the
remaining battery power of the key is
low when the ignition is switched
from ON to ACC or OFF, the
following is indicated.
Replace with a new battery before
the key becomes unusable.
Refer to Key Battery Replacement on
page 6-39.
A message is indicated in the display
of the instrument cluster.
Refer to KEY Warning Indication/
Warning Light (Red) on page 7-56.
x(Automatic transmission)
If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
▼Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number
of times while the engine is running or
the vehicle is being driven will turn the
engine
off immediately. The ignition
switches to ACC.
i-stop*
▼i-stop
The i-stop function automatically stops
the engine when the vehicle is stopped
at a
traffic light or stuck in
traffic, and
then restarts the engine automatically
to resume driving. The system provides
improved fuel economy, reduced
exhaust gas emissions, and eliminates
idling noise while the engine is
stopped.
Engine idle stopping and restarting
NOTE
xAfter parking the vehicle, make sure
that the ignition is switched OFF.
There is the possibility of the vehicle
moving if the vehicle is parked while
i-stop is operating.
xThe i-stop indicator light (green)
turns on under the following
conditions:
xWhen engine idling is stopped.
xThe i-stop indicator light (green)
turns off when the engine is
restarted.
When Driving
Start/Stop Engine
*Some models.4-11

2. When the accelerator pedal is
depressed or the RES switch is
operated while the vehicle is kept
stopped by the MRCC with Stop &
Go function/CTS, the engine
automatically restarts. The engine
restarts automatically when the
accelerator pedal is depressed with
the selector lever in the D/M
position (not in second gear fixed
mode).
(When the vehicle is stopped by the
AUTOHOLD function)
1. When the brake pedal is depressed
while the vehicle is being driven
(except for driving in the R or M
position second gear fixed mode)
and the vehicle is brought to a stop,
the i-stop function will operate and
it continues to operate even if the
brake is released.
2. The engine restarts automatically
when the accelerator pedal is
depressed with the selector lever in
the D/M position (not in second
gear fixed mode).
3. If the selector lever is in the N or P
position, the engine does not
restart when the brake pedal is
released. The engine restarts when
the brake pedal is depressed again
or the selector lever is shifted to the
D, M (not in second gear fixed
mode) or the R position. (For the
purposes of safety, always keep the
brake pedal depressed when
shifting the selector lever while
engine idling is stopped.)
Engine idle stopping and restarting
while driving (With M Hybrid)
(When not using MRCC with Stop &
Go function/CTS)
1. Engine idling stops when the
vehicle speed is about 20 km/h (12
mph) or slower after depressing the
brake pedal while driving the
vehicle (in D position).
2. The engine restarts automatically
after releasing the brake pedal with
the selector lever in the D position.
(When using MRCC with Stop & Go
function/CTS)
1. Engine idling stops when the
vehicle speed is about 20 km/h (12
mph) or slower after decelerating
the vehicle a certain amount or
more while in headway control
using the MRCC with Stop & Go
function/CTS.
2. If it is necessary to accelerate while
in headway control using the MRCC
with Stop & Go function/CTS, the
engine restarts automatically.
Operation conditions
Under the following conditions, engine
idling stops and the i-stop indicator
light (green) turns on.
x(SKYACTIV-G 2.0,
SKYACTIV-G 2.5,
SKYACTIV-X 2.0)
The engine is warmed up.
x(SKYACTIV-D 1.8)
The engine is not cold.
xThe engine has been started and the
vehicle is driven for a certain period.
xThe engine is started with the bonnet
closed.
xAll doors, liftgate, and bonnet are
closed.
xThe driver's seat belt is fastened.xThe air conditioner is not operating
with the airflow mode in the
position.xThe temperature setting dial of the
air conditioner is in a position other
than maximum heating or maximum
cooling (A/C ON) position.
x(Automatic air-conditioning)
The vehicle's interior temperature
and the set temperature for the air
conditioner are nearly the same.
When Driving
Start/Stop Engine
4-13

position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is stopped by
depressing the brake pedal.
xThe vehicle is not driven on a
slope.
xThe vehicle is not stopped
suddenly.
NOTE
Under the following conditions, a
period of time is required to stop
engine idling
xThe battery power is depleted for
some reasons such as the vehicle has
not been driven for a long period.
xThe ambient temperature is high or
low.
xAfter the battery terminals are
disconnected for some reasons such
as for battery replacement.
x(SKYACTIV-D 1.8)
After PM removal is performed by
the diesel particulate filter.
Engine does not restart
If the following operations are
performed while the idling is stopped,
the engine will not restart for safety
reasons. In such cases, start the engine
using the normal method.
x(European model)
xThe bonnet is opened.xThe driver's seat belt is unfastened
and the driver's door is opened.
x(With M Hybrid)
xAutomatic transmission
The driver's seat belt is unfastened
and the driver's door is opened.
xManual transmission
The driver's door is opened.
Engine-stop period is short or time
until next engine idle stop is long
xThe ambient temperature is high or
low.
xThe battery power is depleted.xPower consumption by the vehicle's
electrical parts is high.
Engine restarts automatically while
engine idling is stopped
Under the following conditions, the
engine restarts automatically.
xThe i-stop OFF switch is pressed until
the beep sounds.
xThe air conditioner is operated with
the airflow mode in the
position.xThe temperature setting dial of the
air conditioner is in the maximum
heating or maximum cooling (A/C
ON) position.
x(Automatic air-conditioning)
The cabin temperature is largely
different from the set temperature of
the air conditioner.
xThe brakes are released slightly on a
slope and the vehicle begins to
move.
xTwo minutes have elapsed since the
idling was stopped.
xThe battery power is depleted.x(Automatic transmission)
Engine idling is stopped while the
vehicle is stopped
xThe accelerator pedal is depressed
with the selector lever in the D or
M (not in second gear fixed mode)
position.
xThe selector lever is shifted to the R
position.
xThe selector lever is shifted from N
or P position to D or M (not in
second gear fixed mode) position.
When Driving
Start/Stop Engine
4-15

Operating Tips
▼Operating Tips
xOperate the air-conditioning system
with the engine running.
xTo prevent the battery from being
discharged, do not leave the fan
control dial/switch on for a long
period of time with the ignition
switched ON when the engine is not
running.
x(With i-stop)
The
airflow amount may decrease
slightly while the i-stop function is
operating.
xClear all obstructions such as leaves,
snow and ice from the bonnet and
the air inlet in the cowl grille to
improve the system efficiency.
xUse the air-conditioning system to
defog the windows and dehumidify
the air.
xThe recirculate mode should be used
when driving through tunnels or
while in a
traffic jam, or when you
would like to shut off outside air for
quick cooling of the interior.
xUse the outside air position for
ventilation or windscreen defrosting.
xIf the vehicle has been parked in
direct sunlight during hot weather,
open the windows to let warm air
escape, then run the air-conditioning
system.
xRun the air conditioner about 10
minutes at least once a month to
keep internal parts lubricated.
xHave the air conditioner checked
before the weather gets hot. Lack of
refrigerant may make the air
conditioner less efficient.
The refrigerant specifications are
indicated on a label attached to the
inside of the engine compartment. If
the wrong type of refrigerant is used,
it could result in a serious
malfunction of the air conditioner.
Consult a professional, government
certified repairer for the inspection
or repair because a special device is
required for the air conditioner
maintenance.
For details, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
1. Label
Interior Features
Air-Conditioning System
5-2

NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector switch
This switch controls the source of air
entering the vehicle.

Outside or recirculated air positions
can be selected. Press the switch to
select outside/recirculated air
positions.
Recirculated air position (indicator
light illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested
traffic (high engine exhaust
areas) or when quick cooling is
desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
WARNING
Do not use the position (indicator
light turns on) in cold or rainy
weather:
Using the
position (indicator light
turns on) in cold or rainy weather is
dangerous as it will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident.
Windscreen defroster switch
Press the switch to defrost the
windscreen and front door windows.
Refer to Windscreen Defrosting and
Defogging on page 5-7.
Rear window defogger switch
Press the rear window defogger switch
to defrost the rear window.
Refer to Rear Window Defogger on
page 4-66.
▼Heating
1. Press the switch.
2. Set the air intake selector to the
outside air position (indicator light
turns off).
3. Set the temperature control dial to
the hot position.
4. Set the fan control dial to the
desired speed.
5. If dehumidified heating is desired,
turn on the air conditioner.
NOTE
xIf the windscreen fogs up easily, press
the
switch.xIf cooler air is desired at face level,
press the
switch and adjust the
temperature control dial to maintain
maximum comfort.
xThe air to the
floor is warmer than air
to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
▼Cooling
1. Press the switch.
2. Set the temperature control dial to
the cold position.
3. Set the fan control dial to the
desired speed.
4. Turn on the air conditioner by
pressing the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature
control dial as needed to maintain
maximum comfort.
Interior Features
Air-Conditioning System
5-6

CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffic,
monitor the high engine coolant
temperature warning indication to see
if it is displayed (page 7-51).
The air conditioner may cause engine
overheating. If the warning indication
is displayed, turn the air conditioner
off (page 7-44).
NOTE
xWhen maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector to the
recirculated air position, then turn
the fan control dial fully clockwise.
xIf warmer air is desired at
floor level,
press the
switch and adjust the
temperature control dial to maintain
maximum comfort.
xThe air to the floor is warmer than air
to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
▼Ventilation
1. Press the switch.
2. Set the air intake selector to the
outside air position (indicator light
turns off).
3. Set the temperature control dial to
the desired position.
4. Set the fan control dial to the
desired speed.
▼Windscreen Defrosting and
Defogging
1. Press the switch.
2. Set the temperature control dial to
the desired position.
3. Set the fan control dial to the
desired speed.
4. If dehumidified heating is desired,
turn on the air conditioner.
WARNING
Do not defog the windscreen using
the
switch with the temperature
control set to the cold position:
Using the
switch with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog
up. Your vision will be hampered,
which could lead to a serious accident.
Set the temperature control to the hot
or warm position when using the
switch.
NOTE
xFogging on the windows clears up
more easily while the air conditioner
is on, but they will fog up more easily
if the air conditioner is turned
off.
xBe careful that the windows do not
fog up when doing any of the
following:
xSwitching to recirculate modexTurning off the air conditionerxFor maximum defrosting , turn on the
air conditioner, set the temperature
control dial to the extreme hot
position, and turn the fan control
dial fully clockwise.
xIf warm air is desired at the floor,
press the
switch.
xWith the switch, the outside air
position is automatically selected to
defrost the windscreen. The air
intake selector cannot be changed to
the recirculated air position.
Interior Features
Air-Conditioning System
5-7

The functions for switches other
than those operated continue to
operate in auto control.
Power switch (System On/Off)
The air-conditioning system turns on or
off by pressing the power switch.
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and anticlockwise for
cold.
Turn the temperature control dial to
adjust the temperature between 15 °C
(60 °F) and 29 °C (84 °F).
xWhen the SYNC switch is on:
Turn the driver temperature control
dial to control the temperature
throughout the entire cabin.
xWhen the SYNC switch is off:
Turn the driver or front passenger
temperature control dial to
independently control the
temperature on each side of the
cabin.
NOTE
xThe air-conditioning system changes
to the individual operation mode
(SYNC switch indicator light turns
off) by turning the front passenger
temperature control dial even when
the SYNC switch is on, which allows
individual control of the set
temperature for the driver and front
passenger.
xWhen you set the temperature to the
lower or upper limit, “Lo” or “Hi” is
displayed.
xThe temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
Refer to Outside Temperature
Display on page 4-28.
Fan control switch
The fan has 7 speeds. The selected
speed will be displayed.
Mode selector switch
The desired
airflow mode can be
selected (page 5-4).
NOTE
xWith the airflow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and
air at a comparably lower
temperature will flow through the
central, left and right vents.
xTo set the air vent to , press the
windscreen defroster switch.
xIn the position, the outside air
position is automatically selected.
A/C switch
Pressing the A/C switch while the
AUTO switch is turned on will turn
off
the air conditioner (cooling/
dehumidifying functions).
The on/off of the air conditioner
switches each time the A/C switch is
pressed.
NOTE
xThe air conditioner operates when
the A/C switch is pressed while the
air conditioner is turned off.
xThe air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector switch
Outside or recirculated air positions
can be selected. Press the switch to
select outside/recirculated air
positions.
Interior Features
Air-Conditioning System
5-10