2019 MAZDA MODEL CX-30 alarm

Theft-Deterrent System*
▼Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or
its contents being stolen, the alarm
alerts the surrounding area of an
abnormality by sounding the siren/
horn and flashing the hazard warning
lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic
waves to detect movement inside the
vehicle and to raise an alert of an
intrusion into the vehicle.

The intrusion sensor detects certain
kinds of movement inside the vehicle,
however, it may also respond to
phenomenon outside the vehicle such
as vibrations, loud noise, wind, and air
currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
¾Do not hang clothing or objects from
a head restraint or a coat hook.
¾Return the extension sunvisors to
their original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
¾Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
¾Do not install seats that are not
Mazda genuine products.
¾To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

1. Intrusion sensor and intrusion
sensor bezel
▼Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently
and the hazard warning lights flash for
about 30 seconds when the system is
triggered by any one of the following:
With the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
xThe intrusion sensor detects a
movement in the vehicle.
Before Driving
Security System
*Some models.3-49

The system will be triggered again (up
to 10 times) if one of the above
conditions remains.

xDisconnecting the battery terminal
(the hazard warning lights do not
flash).
The system will be triggered about 10
times.
Without the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
NOTE
xThe liftgate does not open while the
theft-deterrent system is operating.
xIf the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the
hazard warning lights will flash when
the battery is charged or replaced.
▼How to Arm the System
1. Close the windows and the
sunroof* securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof*
open, the system can be armed,
however, leaving the windows or
the sunroof
* even partially open can
invite theft, and wind blowing into
the vehicle could trigger the alarm.
The intrusion sensor function can
also be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors,
and the liftgate are closed.
4. Press the lock button on the
transmitter.
The hazard warning lights will flash
once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch “
”
while any door is open and then
close all of the doors.
(With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully
armed.
Before Driving
Security System
3-50*Some models.

NOTE
xThe theft-deterrent system can
also be armed by activating the
auto relock function with all the
doors, the liftgate and the bonnet
closed.
Refer to Transmitter on page 3-5.
xThe system will disarm if one of
the following operations takes
place within 20 seconds after
pressing the lock button:
xUnlocking any door.xOpening any door.xOpening the bonnet.xSwitching the ignition ON.
To rearm the system, do the
arming procedure again.
xWhen the doors are locked by
pressing the lock button on the
transmitter while the
theft-deterrent system is armed,
the hazard warning lights will
flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With the Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the
intrusion sensor to prevent the alarm
from triggering unnecessarily.
xLeaving the vehicle with a movable
object, passengers or pets remaining
inside.
xLeaving an object inside the vehicle
that can roll around, such as when
the vehicle is placed on a tilting,
unstable surface when being
shipped.
xHanging small objects/accessories in
the vehicle, hanging clothing on a
coat hook, or placing other items
which can move easily inside the
vehicle.
xParking in an area where there is
strong vibration or loud noise.
xWhen using a high pressure or
automatic car wash.
xContinuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
xDoors are locked with a window or
the sunroof* left open.xAn accessory heater or device that
produces moving air and vibration
operates while the theft deterrent
system is armed.
NOTE
If any door or the liftgate remains
closed for 30 seconds, all the doors
and the liftgate automatically re-lock
and the theft deterrent system arms
even if a window and the sunroof
* is
left open.

To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash 3
times.
NOTE
xTo reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
xThe intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the
theft-deterrent system is armed.
▼To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Before Driving
Security System
*Some models.3-51

xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
The hazard warning lights will flash
twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard
warning lights will flash twice to
indicate that the system is turned off.
▼To Stop the Alarm
A triggered alarm can be turned off
using any one of the following
methods:
xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
xPressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will
flash
twice.
Before Driving
Security System
3-52

▼Multi-information Display
1. Multi-information Display
2. INFO switch

The multi-information display indicates the following information.
xSpeedometerxOdometerxTr i p m e te rxOutside temperaturexDistance-to-emptyxAverage fuel economyxCurrent fuel economyxDeceleration Regeneration Charge Display (M Hybrid)xi-ACTIVSENSE DisplayxVehicle Speed Alarm*
xDoor-Ajar/Liftgate-Ajar Warning Indication*1
xMessage Display
*1 Displayed when opening door/liftgate.
When Driving
Instrument Cluster and Display
*Some models.4-23

▼Deceleration Regeneration Charge
Display (M Hybrid)
This displays the status of the charging
produced by deceleration
regeneration.
Refer to M Hybrid on page 4-86.
▼Vehicle Speed Alarm*
In this mode, the current setting for the
vehicle speed alarm is displayed. You
can change the vehicle speed setting at
which the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard.
1. “Speed Alert” message is displayed

The vehicle speed alarm can be set
using the centre display.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
Always set the vehicle speed according
to the laws and regulations of the
country/city in which the vehicle is
driven. In addition, always verify the
speed of the vehicle using the
speedometer.
▼i-ACTIVSENSE Display
Displays the system status.

xRefer to Lane Departure Warning
System (LDWS) on page 4-105.
xRefer to Blind Spot Monitoring
(BSM) on page 4-109.
xRefer to
Tra ffi c Sign Recognition
System (TSR) on page 4-113.
xRefer to Distance & Speed Alert
(DSA) on page 4-119.
xRefer to Driver Attention Alert (DAA)
on page 4-120.
xRefer to Driver Monitoring (DM) on
page 4-122.
xRefer to Front Cross Traffic Alert
(FCTA) on page 4-123.
xRefer to Mazda Radar Cruise Control
(MRCC) on page 4-131.
xRefer to Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function) on page
4-141.
xRefer to Cruising & Traffic Support
(CTS) on page 4-152.
xRefer to Lane-keep Assist System
(LAS) on page 4-165.
xRefer to Adjustable Speed Limiter
(ASL) on page 4-166.
When Driving
Instrument Cluster and Display
4-30*Some models.

stops flashing and remains on. The warning sound is activated continuously until
the vehicle speed decreases below the speed limit sign.
Speed Limit Sign Threshold setting
x+ 0: If the vehicle speed exceeds the speed limit sign displayed in the display, the
excessive speed warning is activated.
x+ 5: If the vehicle speed exceeds the speed limit sign displayed in the display by 5
km/h (3 mph), the excessive speed warning is activated.
x+ 10: If the vehicle speed exceeds the speed limit sign displayed in the display by
10 km/h (5 mph), the excessive speed warning is activated.
NOTE
xIn the following cases, the excessive speed warning stops operating.
xThe vehicle speed is less than the speed of the displayed speed limit sign. (If the
activation timing for the excessive speed warning is changed in the
personalisation features, the excessive speed warning stops operating when the
vehicle speed is less than the changed vehicle speed.
xA speed limit sign indication has been updated and the vehicle speed is lower
than the updated indication.
xDisplay of the speed limit sign stops.xThe warning indication is displayed at the same time the excessive speed warning
sound is activated if the vehicle speed exceeds the speed indicated on the speed
limit sign.
Refer to Excessive Speed Warning on page 7-72.
xIf the Forward Sensing Camera (FSC) or data recorded in the navigation system
incorrectly recognises the actual speed limit sign at a lower speed, the excessive
speed alarm is activated even if the vehicle is driven at the legal speed.
When Driving
i-ACTIVSENSE
4-117

that engine idling is stopped. It stops
when the driver's door is closed.
x(European model)
The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not
restart automatically to ensure safety.
Start the engine using the normal
method.
(With M Hybrid)
x(Manual transmission)
With the shift lever in a position
other than neutral, the driver's
door is opened.
x(Automatic transmission)
With the selector lever in the D or
M (not in second gear
fixed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
(Without M Hybrid)
x(Manual transmission)
With the shift lever in a position
other than neutral, the driver's seat
belt is unfastened and the driver's
door is opened.
x(Automatic transmission)
With the selector lever in the D or
M (not in second gear fixed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
▼Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under
the following conditions:
xThe vehicle is driven with the parking
brake applied.
xThe Electric Parking Brake (EPB)
switch is pulled while the vehicle is
driven.
xYou attempt to start driving the
vehicle while the conditions for
releasing the Electric Parking Brake
(EPB) automatically have not been
met.
▼AUTOHOLD Warning Beep
Message is displayed and beep sound
is activated simultaneously for about 5
seconds when using AUTOHOLD
function or when AUTOHOLD switch
is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.

If the message is displayed and the
beep sound is activated
simultaneously, have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Outside Temperature Warning
Beep*
Warns the driver of the possibility of icy
roads when the outside temperature is
low.
If the outside temperature is lower
than about 4 °C (39 °F) , a beep sound
is heard once and the outside
temperature display
flashes for about
10 seconds.
Refer to Outside Temperature Display
on page 4-28.
▼Vehicle Speed Alarm*
The vehicle speed alarm function is
designed to alarm the driver via a
single beep sound and a warning
indication in the instrument cluster
that the previously set vehicle speed
has been exceeded.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-70*Some models.