2019 MAZDA MODEL CX-30 start stop button

Keyless Entry System
▼Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors,
liftgate, and fuel-filler flap, and opens/
closes the liftgate.
The system can start the engine
without having to take the key out of
your purse or pocket.
Operating the theft-deterrent system is
also possible on theft-deterrent
system-equipped vehicles.

System malfunctions or warnings are
indicated by the following warning
lights or beeps.
Check the displayed message for more
information and, if necessary, have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer), according to the indication.
xKEY Warning Indication/Warning
Light (Red)
Refer to KEY Warning Indication/
Warning Light (Red) on page 7-56.
xIgnition Not Switched Off (STOP)
Warning Beep
Refer to Ignition Not Switched Off
(STOP) Warning Beep on page
7-67.
xKey Removed from Vehicle Warning
Beep
Refer to Key Removed from Vehicle
Warning Beep on page 7-68.
If you have a problem with the key,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).

If your key is lost or stolen, consult an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible for a replacement and to
make the lost or stolen key inoperative.
CAUTION
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
NOTE
xThe keyless entry system operation
may vary due to local conditions.
xThe keyless entry system is fully
operational when the ignition is
switched off. The system does not
operate if the ignition is switched to
any position other than off.
xIf the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new
battery, refer to Key Battery
Replacement (page 6-39).
xBattery life is about 1 year. Replace
the battery with a new one if the
messages are displayed in the
instrument cluster. Replacing the
battery about once a year is
recommended because the KEY
warning indication may not display
depending on the rate of battery
depletion.
xAdditional keys can be obtained at
an Authorised Mazda Repairer. Up
to 6 keys can be used with the
keyless functions per vehicle. Bring
all keys to an Authorised Mazda
Repairer when additional keys are
required.
Before Driving
Keys
3-4

xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
The hazard warning lights will flash
twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard
warning lights will flash twice to
indicate that the system is turned off.
▼To Stop the Alarm
A triggered alarm can be turned off
using any one of the following
methods:
xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
xPressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will
flash
twice.
Before Driving
Security System
3-52

Ignition Switch
▼Push Button Start Positions
The system operates only when the key
is within operational range.
Each time the push button start is
pressed, the ignition switches in the
order of
off, ACC, and ON. Pressing
the push button start again from ON
switches the ignition
off.
1. Indicator light
2. Push button start
NOTE
xThe engine starts by pressing the
push button start while depressing
the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission). To switch
the ignition position, press the push
button start without depressing the
pedal.
xDo not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission,
the selector lever is in the P position,
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
Off
The power supply to electrical devices
turns off and the indicator light
(amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat,
always switch the ignition off, set the
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
accident.
In addition, if your intention is to leave
the vehicle for even a short period, it is
important to switch the ignition
off, as
leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is
flashing , a message is
displayed on the multi-information,
and the beep sound is heard, this
indicates that the steering wheel is not
unlocked. To unlock the steering
wheel, press the push button start
while moving the steering wheel left
and right.
When Driving
Start/Stop Engine
4-4

ACC (Accessory)
Some electrical accessories will
operate and the indicator light (amber)
illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start
has been pressed to ACC, and the
doors will not lock/unlock even if they
have been locked manually.
ON
This is the normal running position
after the engine is started. The
indicator light (amber) turns off. (The
indicator light (amber) illuminates
when the ignition is switched ON and
the engine is not running.)
Some indicator lights/warning lights
should be inspected before the engine
is started.
Refer to Warning/Indicator Lights on
page 4-32.
Refer to Indication/Indicator Lights on
page 4-34.
NOTE
(SKYACTIV-G 2.0, SKYACTIV-G 2.5,
SKYACTIV-X 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
▼Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
xThe key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
xThe engine can be started when the
push button start is pressed from off,
ACC, or ON.
xThe push button start system
functions (function which can start
the engine by only carrying the key)
can be deactivated to prevent any
possible adverse effect on a user
wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable to
start the engine by carrying the key.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-8.
xAfter starting a cold engine, the
engine speed increases and a
whining sound from the engine
compartment can be heard.
When Driving
Start/Stop Engine
4-5

This is for improved exhaust gas
purification and does not indicate
any parts defect.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to depress the brake
pedal firmly until the engine has
completely started.
5.(Manual transmission)
Continue to depress the clutch
pedal firmly until the engine has
completely started.
(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
NOTE
x(Manual transmission)
The starter will not operate if the
clutch pedal is not depressed
sufficiently.
x(Automatic transmission)
The starter will not operate if the
selector lever is not in P or N
position and the brake pedal is
not depressed sufficiently.
6. Make sure that the push button
start indicator light (green) turns
on.
1. Indicator light
2. Push button start
NOTE
xIf the push button start indicator
light (green) flashes, make sure
that the key is being carried.
xIf the push button start indicator
light (green)
flashes with the key
being carried, touch the key to
the push button start and start
the engine.
Refer to Engine Start Function
When Key Battery is Dead on
page 4-8.
CAUTION
If the KEY warning indication (red)
is displayed, or the push button
start indicator light (amber)
flashes,
this could indicate a problem with
the engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC
or ON.
Refer to KEY Warning Indication/
Warning Light (Red) on page
7-56.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
NOTE
xUnder the following conditions,
the KEY warning indication (red)
is displayed after the push button
start is pressed. This informs the
driver that the push button start
will not switch to ACC, even if it
is pressed from off (page 7-56).
xThe key battery is dead.xThe key is out of operational
range.
xThe key is placed in areas where
it is difficult for the system to
detect the signal (page 3-7).
When Driving
Start/Stop Engine
4-6

xA key from another
manufacturer similar to the key
is in the operational range.
x(Forced engine starting method)
If the KEY warning indication
(red) is displayed, or the push
button start indicator light
(amber) flashes, this could
indicate that the engine may not
start using the usual starting
method (page 7-56). Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible. If this occurs,
the engine can be force-started.
Press and hold the push button
start until the engine starts. Other
procedures necessary for starting
the engine, such as having the key
in the cabin, and depressing the
clutch pedal (manual
transmission) or the brake pedal
(automatic transmission) are
required.
xWhen the engine is force-started,
the KEY warning indication (red)
remains displayed and the push
button start indicator light
(amber) remains flashing.
x(Automatic transmission)
When the selector lever is in the
neutral (N) position, the push
button start indicator light (green)
does not turn on.
7. Press the push button start after the
push button start indicator light
(green) turns on.
NOTE
xAfter starting the engine, the push
button start indicator light
(amber) turns off and the ignition
switches to the ON position.
x(SKYACTIV-G 2.0, SKYACTIV-G
2.5, SKYACTIV-X 2.0)
After pressing the push button
start and before the engine starts,
the operation sound of the fuel
pump motor from near the fuel
tank can be heard, however, this
does not indicate a malfunction.
x(SKYACTIV-D 1.8)
xThe starter does not rotate until
the glow indicator light turns
off.
xIf the ignition is left switched
ON for a long period of time
without the engine running
after the glow plugs are
warmed up, the glow plugs may
warm up again which will
illuminate the glow indicator
light.
xWhen starting the engine, do
not release the clutch pedal
(manual transmission) or the
brake pedal (automatic
transmission) until the glow
indicator light in the instrument
cluster turns off and the engine
starts, after pressing the push
button start.
xIf the clutch pedal (manual
transmission) or the brake
pedal (automatic transmission)
is released before the engine
starts, depress the clutch pedal
(manual transmission) or the
brake pedal (automatic
transmission) again and press
the push button start to start
the engine.
8. After starting the engine, let it idle
for about 10 seconds (Prohibited in
Germany).
When Driving
Start/Stop Engine
4-7

NOTE
x(Germany)
Drive immediately after starting
the engine. However do not use
high engine speeds until reaching
the operating temperature.
x(SKYACTIV-G 2.0, SKYACTIV-G
2.5,
SKYACTIV-X 2.0)
xWhether the engine is cold or
warm, it should be started
without the use of the
accelerator.
xIf the engine does not start the
first time, refer to Starting a
Flooded Engine under
Emergency Starting. If the
engine still does not start, have
your vehicle inspected by an
expert repairer (we recommend
an Authorised Mazda Repairer)
(page 7-42).
x(SKYACTIV-D 1.8)
If the ambient temperature is
lower than about >+ 10 °C (14
°F), the maximum engine speed
may not be attained for about 3
minutes after the engine starts to
protect the engine.
x(Manual transmission vehicle
with i-stop function)
If the engine has stopped due to
stalling , it can be restarted by
depressing the clutch pedal
within 3 seconds of the engine
stopping.
The engine cannot be restarted
even if the clutch pedal is
depressed under the following
conditions:
xThe driver's door is open.xThe driver's seat belt is
unfastened.
xThe clutch pedal is not released
completely after the engine
stalled.
xThe clutch pedal is depressed
with the engine not stopped
completely.
▼Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not to
allow the following , otherwise the
signal from the key will not be received
correctly and the engine may not start.
¾Metal parts of other keys or metal
objects touch the key.
¾Spare keys or keys for other vehicles
equipped with an immobilizer
system touch or come near the key.
¾Devices for electronic purchases, or
security passage touch or come near
the key.
If the engine cannot be started due to
a dead key battery, the engine can be
started using the following procedure:
1. Continue to depress the brake
pedal firmly until the engine has
completely started.
2.(Manual transmission)
Continue to depress the clutch
pedal
firmly until the engine has
completely started.
When Driving
Start/Stop Engine
4-8

(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
3. Make sure that the push button
start indication light (green) flashes.
4. Align the centre area of the emblem
on the transmitter with the centre
area of the push button start while
the push button start indicator light
(green) flashes.

1. Indicator light
2. Push button start
3. Transmitter
4. Emblem

5. Make sure that the push button
start indicator light (green) turns
on.
6. Press the push button start to start
the engine.
NOTE
xThe engine cannot be started
unless the clutch pedal is fully
depressed (manual transmission)
or the brake pedal is fully
depressed (automatic
transmission).
xIf there is a malfunction with the
push button start function, the
push button start indicator light
(amber) flashes. In this case, the
engine may start, however, have
the vehicle checked at an expert
repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
xIf the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle
checked at an expert repairer (we
recommend an Authorised
Mazda Repairer).
xTo switch the ignition position
without starting the engine,
perform the following operations
after the push button start
indicator light (green) turns on.
1. Release the clutch pedal
(manual transmission) or
brake pedal (automatic
transmission).
2. Press the push button start to
switch the ignition position.
The ignition switches in the
order of ACC, ON, and off
each time the push button
start is pressed. To switch the
ignition position again,
perform the operation from
the beginning.
▼Emergency Operation for Starting
the Engine
If the KEY warning indication (red) is
displayed, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
When Driving
Start/Stop Engine
4-9