2019 MAZDA MODEL CX-30 length

recommend an Authorised Mazda
Repairer).
xMake sure the trailer cargo is secure
to prevent it from shifting.
xMake sure the mirrors meet all
government regulations. Inspect
them.
xBefore starting out, inspect the
operation of all vehicle and trailer
lights and all vehicle-to-trailer
connections. Stop and re-inspect all
lights and connections after driving a
short distance.
Driving
xYour Mazda will handle differently
with a trailer in tow, so practice
turning , backing , and stopping in a
traffic-free area.
xTake time to get accustomed to the
extra weight and length.
xDo not exceed 100 km/h (62 mph)
with a trailer in tow. If the local legal
maximum speed with a trailer in tow
is less than 100 km/h (62 mph), do
not exceed the legal speed.
CAUTION
If the vehicle exceeds 100 km/h (62
mph) with a trailer in tow, the
vehicle could be damaged.
xWhen ascending a hill, shift into a
lower gear to reduce the possibility
of overloading or overheating the
engine, or both.
xWhen descending a hill, shift into a
lower gear and use engine
compression as a braking effect. Pay
constant attention to speed and use
the brakes only as needed. Holding
the brake pedal down for a
prolonged period may cause the
brakes to overheat and lose power.
Parking
Avoid parking on an incline with a
trailer. If this must be done, follow
these instructions.
Parking on an Incline
1. Set the parking brake and the
brakes.
2. Have someone block the wheels of
the vehicle and trailer while you
apply the brakes.
3. After the wheels are blocked,
release the parking brake and the
brakes slowly, allowing the blocks
to bear the load.
4. Set the parking brake firmly.
5. If the vehicle has an automatic
transmission, put the selector lever
in P position. If it has a manual
transmission, place the gear shift in
1 or R position.
Starting on an Incline
1. Start the engine (page 4-5).
2. Release the parking brake and
slowly pull away a short distance
from the wheel blocks.
3. Stop on the nearest level ground,
set the parking brake, and pick up
the wheel blocks.
Before Driving
Towing
3-67

Switch Posi-
tionWiper operation
High speed
Variable-speed intermittent wipers
Set the lever to the intermittent
position and choose the interval timing
by rotating the switch.
Rotate the switch upward to shorten
the interval time of the wiper
operation, and rotate the switch
downward to lengthen it.

1. Switch
2. Shorten
3. Lengthen
With auto-wiper control

1. Indicator light
Switch Position
Wiper operation
No. Type A Type B
MISTOperation while
pulling up lever
OFF Stop
AUTO*1AUTO*1Auto control
LO Low speed
HI High speed
*1 When the wiper lever is switched to the
AUTO position, the indicator light turns on.
Auto-wiper control*
When the wiper lever is in the AUTO
position, the rain sensor senses the
amount of rainfall on the windscreen
and turns the wipers on or off
automatically
(offŠintermittentŠlow
speedŠhigh speed).

The sensitivity of the rain sensor can be
adjusted by turning the switch on the
wiper lever.
From the centre position (normal),
rotate the switch upward for higher
sensitivity (faster response) or rotate it
downward for less sensitivity (slower
response).

1. Switch
2. Higher sensitivity
3. Centre position
4. Less sensitivity
When Driving
Switches and Controls
4-62*Some models.

NOTE
xWhen you resume driving by pressing
the RES switch, your vehicle does not
start moving until the distance
between your vehicle and the vehicle
ahead lengthens to the
specified
distance or farther.
xThe engine restarts automatically
when any of the actions to resume
driving are performed while i-stop is
operating.
xIf the MRCC with Stop & Go
function is temporarily cancelled
during stop hold control, you cannot
resume driving by pressing the RES
switch when there are no vehicles in
front of your vehicle. Depress the
accelerator pedal and resume driving
the vehicle.
xIf the vehicle ahead starts moving
within 3 seconds after your vehicle is
stopped by the stop hold control,
headway control will resume even if
you do not resume driving your
vehicle, such as by depressing the
accelerator pedal.
Resume driving information
If you do not resume driving within a
few seconds after the vehicle ahead
starts moving , the multi-information
display vehicle-ahead indication
flashes to urge the driver to resume
driving. If you do not resume driving
after the indicator light flashes, a
sound is activated to urge you to
resume driving.
Cruising & Traffic Support
(CTS)
*
▼Cruising & Traffic Support (CTS)
The CTS is a system which consists of a
headway control function and a
steering assist function for reducing
driver fatigue during traffic jams when
driving on expressways or highways.
This system performs headway control
to maintain a constant distance
between your vehicle and a vehicle
ahead at a preset vehicle speed
without you having to use the
accelerator or brake pedal. Even
further, with the steering assist
function, when vehicle lane lines are
detected, the function assists the driver
in keeping the vehicle within the lane
lines. If lane lines are not detected, the
function provides the driver driving
assistance in keeping the vehicle along
the motion path with the vehicle
ahead.
WARNING
Do not rely completely on CTS:
¾The CTS is not an automated driving
system. In addition, the functions
have limitations. Do not rely
completely on the system and always
stay on course using the steering
wheel.
¾Set a vehicle speed within the speed
limit according to the road
conditions and the weather
conditions.
When Driving
i-ACTIVSENSE
4-148*Some models.

Request Indication on display
Shift up Shift Up to a Higher Gear
Shift down Shift Down to a Lower Gear
NOTE
xIf the gears are not shifted up even
though the shift-up request
indication is displayed, load will be
applied to the engine and the CTS
might be automatically cancelled or
engine damage could occur.
xIf the gears are not shifted down
even though the shift-down request
indication is displayed, the CTS
might be automatically cancelled or
engine stalling could occur.
▼Stop Hold Control (Automatic
Transmission)
While in headway control using the
CTS, your vehicle will stop when a
vehicle ahead stops. When the vehicle
is stopped and the stop hold control
operates, the CTS indicator light turns
on.
NOTE
xEven if the CTS is temporarily
cancelled during stop hold control,
the vehicle is held in its stopped
position.
xThe parking brake is automatically
applied and the vehicle is held in its
stopped position when 10 minutes
or longer have passed since the stop
hold control operated. When this
occurs, the CTS is temporarily
cancelled.
xIf the i-stop operation conditions are
met during stop hold control, the
engine stops even though the brake
pedal is not depressed.
Refer to i-stop on page 4-11.
xThe brake lights turn on during stop
hold control.

To resume driving
After the vehicle ahead starts moving
while your vehicle is stopped under
stop hold control, press the RES switch
or depress the accelerator pedal to
cancel the stop hold control and start
driving.
NOTE
xWhen you resume driving by pressing
the RES switch, your vehicle does not
start moving until the distance
between your vehicle and the vehicle
ahead lengthens to the
specified
distance or farther.
xThe engine restarts automatically
when any of the actions to resume
driving are performed while i-stop is
operating.
xIf the CTS is temporarily cancelled
during stop hold control, you cannot
resume driving by pressing the RES
switch when there are no vehicles in
front of your vehicle. Depress the
accelerator pedal and resume driving
the vehicle.
When Driving
i-ACTIVSENSE
4-161

Item Capacity
Fuel tankFWD51.0 L (13.5 US gal, 11.2 Imp
gal)
AWD48.0 L (12.7 US gal, 10.6 Imp
gal)
Check oil and
fluid levels with dipsticks or reservoir gauges.
▼Dimensions
Item Vehicle specification
Overall length 4,395 mm (173.0 in)
Overall width 1,795 mm (70.7 in)
Overall height 1,540 mm (60.6 in)
Front tread 1,565 mm (61.6 in)
Rear tread 1,565 mm (61.6 in)
Wheelbase 2,655 mm (104.5 in)
▼Light Bulbs
The LED bulb cannot be replaced. Consult an expert repairer (we recommend an
Authorised Mazda Repairer) when the replacement is necessary.
Exterior light
Light bulbCategory
Wattage
UN-R*1 (SAE)
xHeadlightsxPosition lightsxFront direction indicator lightsxSide direction indicator lightsxHigh-mount brake lightxRear direction indicator lightsxBrake lightsxTail lightsxReverse lights
xRear fog light*
xNumber plate lightsLEDŠ (Š)
Running lights
*LED type LEDŠ (Š)
Bulb type
21
*2W21/5W (7444)
*1 UN-R stands for United Nations Regulation.*2
Double-filament light bulb, however, only 21 W
filament bulb is used in the running lights.
Specifications
Specifications
*Some models.9-9