2019 MAZDA MODEL CX-30 low oil pressure

Signal Warning Refer to
(Amber)
*i-stop Warning Indication/Warning Light*17-53
*Automatic Transmission Warning Indication/Warning Light*17-55
*AWD Warning Indication/Warning Light*17-56
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning
Light*17-55
*Tyre Pressure Monitoring System (TPMS) Warning Indication/Warn-
ing Light*1
Flashing
7-57
Tu r n s o n
7-60
(Red)KEY Warning Indication/Warning Light
*17-56
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-58
*Adaptive LED Headlights (ALH) Warning Indication/Warning Light*17-58
i-ACTIVSENSE Warning Indication/Warning Light*17-58
Exterior Light Warning Indication/Warning Light*17-58
Low Fuel Warning Indication/Warning Light 7-58
Engine Oil Level Warning Indication/Warning Light*17-59
*120 km/h Warning Light*17-57
Seat Belt Warning Indication/Warning Light (Front seat) 7-59
(Red)Seat Belt Warning Light (Rear seat) 7-59
When Driving
Instrument Cluster and Display
*Some models.4-33

i-ACTIV AWD Operation
▼i-ACTIV AWD Operation
AWD provides excellent drivability on
snow-covered and ice-packed roads,
sand and mud, as well as on steep
slopes and other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Refer to AWD Warning Indication/
Warning Light on page 7-56.
WARNING
Never spin a wheel that is off the
ground:
Spinning a wheel that is off the ground
as a result of the vehicle being stuck or
in a ditch is dangerous. The drive
assembly could be seriously damaged
which could lead to an accident or
could even lead to overheating, oil
leakage, and a
fire.
▼AWD Driving
This vehicle has not been designed for
the purpose of off-road driving or
rallies. Do not attempt to drive over
uneven or rocky surfaces, or across
rivers.
Although this vehicle is equipped with
AWD, acceleration, steering and
braking operations should be
conducted in the same manner as with
a non-AWD vehicle, with the emphasis
placed on safe driving.
▼Ty re s a n d Ty re C h a i n s
The condition of the tyres plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to
the drive assembly, please note the
following:
Ty re s
xWhen replacing tyres, always replace
all front and rear tyres at the same
time.
xAll tyres must be of the same size,
manufacture, brand and tread
pattern. Pay particular attention
when equipping snow or other types
of winter tyres.
xDo not mix tread-worn tyres with
normal tyres.
xInspect tyre
inflation pressures at the
specified periods adjust to the
specified pressures.
NOTE
Check the tyre
inflation pressure label
attached to driver's door frame for the
correct tyre
inflation pressure.
xMake sure to equip the vehicle with
genuine tyres of the specified size,
on all wheels. With AWD, the system
is calibrated for all 4 wheels being of
the same dimensions.
Tyre chains
xInstall tyre chains to the front tyres.xDo not use tyre chains on the rear
wheels.
xDo not drive the vehicle faster than
30 km/h (19 mph) with the tyre
chains installed.
xDo not drive the vehicle with tyre
chains on road conditions other than
snow or ice.
▼To w i n g
If the vehicle requires towing, have it
towed with all 4 wheels completely
off
the ground.
Refer to Towing Description on page
7-46.
When Driving
i-ACTIV AWD
4-92

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Exhaust system and heat shields IIIIIIIIIIII
Function of all lights I I I I I I I I I I I I
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Tyre inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines & hoses IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) R R R R R R
Hoses and tubes for emission I I I
Air
filter
*9RRRR
Manual transmission oil R R
Fuel filterExcept below
countriesReplace every 120,000 km.
Azerbaijan/
ArmeniaReplace every 60,000 km.
Engine coolant
*10Replace at first 195,000 km or 120 months; after that,
every 90,000 km or 60 months.
Rear differential oil
*11
Transfer oil*11
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust,
fill up, or replace if necessary.
T: Tighten
R: Replace
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
7,500 km or 6 months.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.
Maintenance and Care
Scheduled Maintenance
6-10

3. MIN

SKYACTIV-D 1.8

1. X Mark
2. MAX
3. OK
4. MIN

NOTE
(SKYACTIV-D 1.8)
When inspecting the engine oil
level, pull out the dipstick straight
without twisting. In addition, when
inserting the dipstick, always insert
it without twisting so that the “X”
mark faces the front of the vehicle.
6. Pull it out again and examine the
level.
The level is normal if it is between
the MIN and MAX marks.
If it is near or below MIN, add
enough oil to bring the level to
MAX.
CAUTION
Do not overfill the engine oil. This
may cause engine damage.
7. Make sure the O-ring on the
dipstick is positioned properly
before reinserting the dipstick.
8. Reinsert the dipstick fully.
Engine Coolant
▼Inspecting Coolant Level
WARNING
Do not use a match or live flame in
the engine compartment. DO NOT
ADD COOLANT WHEN THE ENGINE
IS HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Maintenance and Care
Owner Maintenance
6-28

with plain water is ineffective, use a
mild soap made for use on vehicles.

Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the finish.

After washing the vehicle, dry it with a
clean chamois to prevent water spots
from forming.
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
When using an automatic car wash
xRetract the door mirrors.xThe automatic car wash brushes
could reduce the paint lustre or
hasten paint deterioration.
When using a high water pressure car
wash
High water temperature and high
water pressure car washers are
available depending on the type of car
wash machine. If the car washer nozzle
is put too close to the vehicle, the
force of the spray could damage or
deform the molding,
affect the
sealability of parts, and allow water to
penetrate the interior. Keep a
sufficient
space (30 cm (12 in) or more)
between the nozzle and the vehicle. In
addition, do not spend too much time
spraying the same area of the vehicle,
and be very careful when spraying
between gaps in doors and around
windows.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the
finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle
body, wax the metal trim to maintain
its lustre.

1. Use wax which contains no
abrasives.
Waxes containing abrasive will
remove paint and could damage
bright metal parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colours.
3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle does not need it.
▼Paint Damage Touch-up
Repair damage to the finish caused by
stone chipping, damage during parking
etc., by using Mazda touch-up paint
before rust begins to form. First,
remove the dirt and grease with a
clean soft cloth.

If rust has already begun to form:

1. Remove rust completely with
sandpaper.
2. Wipe with a clean soft cloth.
3. Apply rust preventive primer to the
area.
Maintenance and Care
Appearance Care
6-57

▼Plastic Part Maintenance
xWhen cleaning the plastic lenses of
the lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these
chemical agents can discolour or
damage the surfaces resulting in a
significant loss in functionality. If
plastic parts become inadvertently
exposed to any of these chemical
agents, flush with water immediately.
xIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
petrol, oil, engine coolant, or battery
fluid, it could cause discolouration,
staining, or paint peeling. Wipe off
any such chemical agents or fluids
using a soft cloth immediately.
xHigh water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
xDo not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
xIn addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
xDo not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
xRubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following , wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or
peeling of the coating , and it will make
it hard to wipe off later.
xBeverage or fragrancexGrease or oilxSoiling
▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which
have been pulled out for cleaning,
dry them off thoroughly and make
Maintenance and Care
Appearance Care
6-59

When starting the engine, the brake
system warning light may turn on and
the warning indication may be
displayed. In this case, park the
vehicle in a safe location and release
the brake pedal.
If the brake system warning light/
warning indication does not turn off
even after parking the vehicle, have
the vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).

▼Electronic Brake Force Distribution
System Warning
If the electronic brake force
distribution control unit determines
that some components are operating
incorrectly, the control unit may
illuminate the brake system warning
light and the ABS warning light
simultaneously. The problem is likely to
be the electronic brake force
distribution system.
WARNING
Do not drive with both the brake
system warning light and ABS warning
light illuminated. Have the vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the brakes inspected
as soon as possible:
Driving when the brake system warning
light and ABS warning light are
illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly in
an emergency stop than under normal
circumstances.
▼Charging System Warning
Indication/Warning Light
If the warning light illuminates while
driving , it indicates a malfunction of
the alternator or of the charging
system.
Drive to the side of the road and park
off the right-of-way. Consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
CAUTION
Do not continue driving when the
charging system warning light is
illuminated because the engine could
stop unexpectedly.
▼Engine Oil Warning Indication/
Warning Light
This warning light indicates low engine
oil pressure.
CAUTION
Do not run the engine if the oil
pressure is low. Otherwise, it could
result in extensive engine damage.
If the light illuminates or the warning
indication is displayed while driving:
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-50

at an expert repairer (we recommend
an Authorised Mazda Repairer).
xWhen there is a malfunction in the
AWD system.
“Excessive AWD System Load. Drive
Slowly Until Warning Light Turns Off.
Vehicle Now in Front Wheel Drive” is
displayed/When the light is flashing
The indication is displayed/the light
flashes under the following conditions.
Park the vehicle in a safe place and
check that the warning indication light
turns
off/ the warning light stops
flashing, and then drive the vehicle.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer) if the indication is
continuously displayed.
xWhen the differential oil temperature
is excessively high.
xWhen there is a large difference
between the front and rear wheel
rotation, such as when trying to
remove the vehicle from mud.
“Mismatched Tyre Diameters. Vehicle
Now in Front Wheel Drive” is
displayed/When the light is turned on
The indication is displayed/the light
turns on under the following
conditions. Inspect the tyre sizes or
tyre pressures on all 4 wheels. Contact
an expert repairer (we recommend an
Authorised Mazda Repairer) if the
indication remains on or the warning
light remains illuminated.
xWhen any of the tyre diameter is
different.
xWhen any of the tyre pressure is
incorrect.
▼120 km/h Warning Light*
The 120 km/h warning light
illuminates when the vehicle speed
exceeds 120 km/h.
Action to be taken
Lower the vehicle speed.
▼Tyre Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Flashing)
*
If there is a problem with the TPMS or
the voltage of a tyre pressure sensor
decreases, the TPMS warning light
flashes and a message is displayed on
the multi-information display. Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or
flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-57