2019 MAZDA MODEL CX-30 maintenance

▼Plastic Part Maintenance
xWhen cleaning the plastic lenses of
the lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these
chemical agents can discolour or
damage the surfaces resulting in a
significant loss in functionality. If
plastic parts become inadvertently
exposed to any of these chemical
agents, flush with water immediately.
xIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
petrol, oil, engine coolant, or battery
fluid, it could cause discolouration,
staining, or paint peeling. Wipe off
any such chemical agents or fluids
using a soft cloth immediately.
xHigh water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
xDo not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
xIn addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
xDo not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
xRubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following , wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or
peeling of the coating , and it will make
it hard to wipe off later.
xBeverage or fragrancexGrease or oilxSoiling
▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which
have been pulled out for cleaning,
dry them off thoroughly and make
Maintenance and Care
Appearance Care
6-59

sure there is no remaining moisture
on them.
WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
expert repairer (we recommend an
Authorised Mazda Repairer):
If a seat belt is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.
Use a mild detergent to remove
soiling from a seat belt:
If organic solvents are used for cleaning
the seat belts or they become stained
or bleached, there is the possibility of
them becoming weakened and as a
result, they may not function at their
full capacity which could cause serious
injury or death.
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will
make it difficult to clean them later,
and it may
affect the smooth retracting
of the seat belt.
▼Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
▼Upholstery Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe
off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼Leather Upholstery Maintenance*
1. Remove dust and sand using a
vacuum cleaner.
2. Wipe off the soiled area with a soft
cloth and a suitable, special cleaner
or a soft cloth soaked in a mild
detergent (about 5%) diluted with
water.
3. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
4. Remove moisture with a dry, soft
cloth and allow the leather to
further dry in a well-ventilated,
shaded area. If the leather gets wet
such as from rain, remove the
moisture and dry it as soon as
possible.
NOTE
xBecause genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
xTo maintain the quality for as long as
possible, periodical maintenance,
about twice a year, is recommended.
xIf the leather upholstery comes into
contact with any of the following,
clean it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
xSand or dirtxGrease or oil, such as hand creamxAlcohol, such as in cosmetic or
hair dressing items
xIf the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such
as hardening and shrinkage.
Maintenance and Care
Appearance Care
6-60*Some models.

xExposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car
under direct sunlight for long
periods, shade the interior using
sunshades.
xDo not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality
and colouring. If the cabin
temperature becomes hot, the vinyl
may deteriorate and adhere to the
genuine leather.
▼Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discolouration, stains,
cracks or peeling of the coating.
▼Instrument Panel Top (Soft pad)
Maintenance
Extremely soft material is used for the
soft pad surface. If the soft pad surface
is rubbed harshly with a dry cloth, it
could result in the surface being
damaged and leaving white scratch
marks.
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5%) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼Active Driving Display
Maintenance*
The dust-proof sheet has a coating.
When cleaning , do not use a hard or
rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving
display, wipe it off immediately. The
dust-proof sheet could be damaged
and the surface coating could be
scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning
the dust-proof sheet is recommended.
▼Panel Maintenance
If a panel becomes soiled, wipe it off
with a soft cloth soaked in clean water
and thoroughly wrung out.
If some areas require further cleaning ,
use the following procedure:
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5 %) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic parts
such as plating as they can be
scratched easily.
▼Cleaning the Window Interiors
If the windows become covered with
an oily, greasy, or waxy
film, clean
them with glass cleaner. Follow the
directions on the container.
CAUTION
¾Do not scrape or scratch the inside
of the window glass. It could
damage the thermal filaments and
the aerial lines.
¾When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water, gently
wiping the thermal filaments and the
aerial lines.
Maintenance and Care
Appearance Care
*Some models.6-61

Use of glass cleaning products could
damage the thermal filaments and
the aerial lines.
Maintenance and Care
Appearance Care
6-62

Ty p e E
1. Jack lever
2. Spare tyre hold-down bolt
3. Screwdriver
*
4. Towing eyelet
5. Jack
6. Spare tyre
7. Wrench
*
8. Wheel brace
▼Jack*
To remove the jack
1. Remove the luggage mat.

2. Remove the jack.

To secure the jack
Perform the removal procedure in
reverse.
Maintenance
xAlways keep the jack clean.xMake sure the moving parts are kept
free from dirt or rust.
xMake sure the screw thread is
adequately lubricated.
▼Spare Tyre*
Your Mazda has a temporary spare
tyre.
The temporary spare tyre is lighter and
smaller than a conventional tyre, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tyres should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare
tyre on the front wheels (driving
wheels):
Driving with the temporary spare tyre
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tyre to the front wheel and install the
temporary spare tyre to the rear.
CAUTION
¾When using the temporary spare
tyre, driving stability may decrease
compared to when using only the
conventional tyre. Drive carefully.
¾To avoid damage to the temporary
spare tyre or to the vehicle, observe
the following precautions:
If Trouble Arises
Flat Tyre
*Some models.7-25

Do not ignore the TPMS warning light
when it is turned on or flashing:
Continuing to drive the vehicle while
ignoring the illumination/flashing of
the TPMS warning light is dangerous
because a tyre may burst which could
lead to an accident. Take appropriate
measures as soon as possible.
▼High Beam Control System (HBC)
Warning Indication/Warning Light
(Amber)
*
The light remains turned on if there is a
problem with the system. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼Adaptive LED Headlights (ALH)
Warning Indication/Warning Light
(Amber)
*
The light remains turned on if there is a
problem with the system. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼i-ACTIVSENSE Warning
Indication/Warning Light*
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
▼Exterior Light Warning Indication/
Warning Light
This light illuminates if there is a
malfunction in the exterior lights
(except number plate lights). Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
CAUTION
Do not drive the vehicle while an
exterior light has a malfunction. Poor
visibility, and not being able to signal
braking and turns may cause an
accident. In addition, if the vehicle is
driven with the lights not turned on, it
may conflict with laws and regulations
due to poor maintenance.
▼Low Fuel Warning Indication/
Warning Light
The light turns on when the remaining
fuel is about 9.0 L (2.3 US gal, 1.9 Imp
gal). If you continue to drive after the
light turns on without refuelling and
the fuel gauge reaches nearly empty,
the light flashes.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-58*Some models.

where contact details are also
provided.

Data, which is exclusively stored locally
on the vehicle, may be viewed with
expert assistance, e.g., in a vehicle
workshop, in return for payment if
appropriate.

Legal requirements regarding the
disclosure of data
To the extent that legal regulations
exist, manufacturers are obliged to
release information stored by them, at
the request of public authorities, to the
extent required on a case-by-case
basis (e.g., when a criminal offence is
being investigated).

Public authorities are also permitted to
read the data from vehicles in specific
cases, within the scope of applicable
law. For example, in the event of an
accident, information can be read from
the air bag control unit to help clarify
the circumstances of the accident.

Operational data on the vehicle
Control units process data in order to
operate the vehicle.

These include, for example:
xvehicle status information (e.g.,
speed, deceleration, lateral
acceleration, wheel speed, seatbelt
usage indicator),
xenvironmental conditions (e.g.,
temperature, rain sensor, distance
sensor).

These data are generally volatile and
are not stored beyond the operating
time, and only processed on the
vehicle itself. Control units frequently
contain data storage media. These can
be used to document, either
temporarily or permanently,
information about the condition of the
vehicle, component stress,
maintenance requirements and
technical events and failures.

The following information may be
stored, depending on the technical
configuration:
xoperating conditions of system
components (e.g.,
fill levels, tyre
pressures and battery status),
xmalfunctions and defects in
important system components (e.g.,
lighting and brakes),
xresponse of the system to
extraordinary driving situations (e.g.,
deployment of an air bag, activation
of stability control systems),
xinformation on events in which the
vehicle is damaged,
xfor electric vehicles, the state of
charge of the high-voltage battery
and the vehicle’s estimated range.

In particular cases (e.g., if the vehicle
has detected a malfunction), it may be
necessary to store data which would
normally be volatile.

If you make use of services (e.g., repair
and maintenance services), it may be
possible, if necessary, to read out and
use the stored operating data together
with the vehicle identification number.
The data from the vehicle may be read
out by employees of the Mazda
Network (e.g. authorised workshops,
manufacturer) or by third parties (e.g.,
breakdown services, independent
repair shops). The same applies in the
case of warranty cases and quality
assurance measures.

The data is usually read out via the
mandatory OBD (on-board
Customer Information
Collection and Processing of Data in the Vehicle
8-6

diagnostics) connection on the vehicle.
The operating data read out document
the technical conditions of the vehicle
or individual components and help
with fault diagnostics, compliance with
warranty obligations and quality
improvement. These data, in particular
information regarding component
stress, technical events, operating
errors and other errors are transmitted
to the manufacturer, if necessary,
together with the vehicle identification
number. In addition, product liability
falls under the responsibility of the
manufacturer. For this purpose, the
manufacturer uses operating data
external to the vehicles, for example,
recall campaigns. These data also may
be used to verify the customer’s
statutory warranty and manufacturer
warranty claims.

Error memory on the vehicle can be
reset by a service operator within the
course of repair and maintenance work
or at your request.

Comfort and infotainment functions
You can store comfort settings and
customisations on the vehicle, and
change/reset these at any time.

Depending on the particular vehicle
configurations, these may include:
xseat and steering wheel position
settings,
xchassis adjustments and
air-conditioning settings,
xcustomisations such as interior
lighting.

You are also able to incorporate data
into the vehicle’s infotainment
functions yourself within the context of
the selected configuration.

Depending on the particular vehicle
configurations, these may include:
xmultimedia data, e.g., music,
films
or photos for playback in an
integrated multimedia system,
xaddress book data for use in
conjunction with an integrated
hands-free system or integrated
navigation system,
xnavigation destinations entered,xdata relating to the use of internet
services.

This data for comfort and infotainment
functions may be stored locally on the
vehicle or it may be located on a
device that you have connected to your
vehicle (e.g., smartphone, USB stick or
MP3 player). Provided that you have
entered this data yourself, you will be
able to delete it at any time.

Transmission of this data from the
vehicle is exclusively at your request, in
particular, relating to the settings you
have selected when using online
services.

Smartphone integration, for example,
Android Auto or Apple car play

If your vehicle is equipped accordingly,
you will be able to connect your
smartphone or another mobile device
to the vehicle so that you can control it
using the integrated control elements
within the vehicle. Smartphone images
and sounds can be output via the
vehicle’s multimedia system. At the
same time, specific information is
transferred to your smartphone.
Depending on the type of integration,
Customer Information
Collection and Processing of Data in the Vehicle
8-7