2019 MAZDA MODEL CX-30 instrument cluster

Traffic Sign Recognition System (TSR)*
▼Tra ffi c Sign Recognition System (TSR)
The TSR helps prevent the driver from overlooking traffic signs, and provides support
for safer driving by displaying traffic signs on the active driving display/instrument
cluster which are recognised by the Forward Sensing Camera (FSC) or recorded in
the navigation system while the vehicle is driven.
The TSR displays the speed limit (including auxiliary signs) , do not enter,
traffic stop,
and passing prohibited
* signs.
If the vehicle speed exceeds the speed limit sign indicated in the active driving
display/instrument cluster while the vehicle is driven, the system notifies the driver
using the indication in the active driving display/instrument cluster and a warning
sound.
Speed limit (including auxiliary signs) , do not enter and passing prohibited
* signs
1. Sign recognised
2. Sign displayed
3. Active driving display indication
When Driving
i-ACTIVSENSE
*Some models.4-111

4. Instrument cluster
5. Basic display
6. i-ACTIVSENSE display
7. Recognized speed limit indication colour changes.
Stop sign
1. Sign recognised and displayed at same time
2. Active driving display indication
3. Instrument cluster
WARNING
Always check the traffic signs visually while driving.
The TSR helps prevent the driver from overlooking traffic signs and provides support
for safer driving. Depending on the weather conditions or problems with traffic
signs, a traffic sign may not be recognised or a traffic sign different from the actual
traffic sign may be displayed. Always make it your responsibility as a driver to check
the actual traffic signs. Otherwise, it could result in an accident.
NOTE
xThe TSR is not supported in some countries or regions. For information concerning
the supported countries or regions, consult an expert repairer (we recommend an
Authorised Mazda Repairer).
xThe TSR operates only if the navigation system SD card (Mazda genuine) is
inserted in the SD card slot. Consult an expert repairer (we recommend an
Authorised Mazda Repairer) for details.
*
When Driving
i-ACTIVSENSE
4-112*Some models.

xThe TSR does not operate if there is a malfunction in the Forward Sensing Camera
(FSC).
xUnder the following conditions, the TSR may not operate normally.
xAn object placed on the instrument panel is reflected in the windscreen and
picked up by the camera.
xHeavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
xThe tyre pressures are not adjusted to the specified pressure.xTyres other than standard tyres are equipped.xThe vehicle is driven on the ramp and surrounding area to or from a rest area or
a tollgate on a highway.
xWhen surrounding brightness suddenly changes such as when entering or exiting
a tunnel.
xThe illumination of the headlights is weakened because of dirt or the optical axis
is deviated.
xThe windscreen is dirty or foggy.xThe windscreen and camera are fogged (water droplets).xStrong light is directed at the front of the vehicle (such as backlight or high-beam
headlights of on-coming vehicles).
xThe vehicle is making a sharp turn.xStrong light reflects off the road.xA traffic sign is in a position which makes it difficult to reflect the light from the
vehicle's headlights, such as when the vehicle is driven at night or in a tunnel.
xThe vehicle is driven under weather conditions such as rain, fog, or snow.xThe stored map data for the navigation system is not current.xA traffic sign is obscured by mud or snow.xA traffic sign is concealed by trees or a vehicle.xA
traffic sign is partially shaded.xA traffic sign is bent or warped.xA
traffic sign is too low or too high.xA traffic sign is too bright or too dark (including electronic traffic signs).xA traffic sign is too big or too small.xThere is an object similar to the traffic sign being read (such as another traffic
sign or other signs resembling it).
xThe TSR can be set to invisible on the active driving display.
Refer to the Settings section in the Mazda Connect Owner's Manual.
▼Traffic Sign Display Indication
The following traffic signs are displayed
on the active driving display/
instrument cluster.
Speed limit signs (including auxiliary
signs)
1. Speed limit signs
2. Auxiliary sign (example)
When Driving
i-ACTIVSENSE
4-113

▼Excessive Speed Warning
If the vehicle speed exceeds the speed limit sign displayed in the active driving
display/instrument cluster, the area around the speed limit sign flashes in amber and
the warning sound is activated at the same time. If the vehicle speed continues to
exceed the displayed speed limit sign, the indication stops flashing and remains on.
Check the surrounding conditions and adjust the vehicle speed to the legal speed
using the appropriate operation such as depressing the brake pedal.
1. Vehicle is doing 90 km/h when 80 km/h speed limit sign is recognised.
2. Vehicle continues to do 90 km/h after 80 km/h speed limit sign is passed.
3. Active driving display indication
4. Instrument cluster

The excessive speed warning is initially set to visual only. If you want to activate the
excessive speed warning , change the setting in the personalisation features. In
addition, the warning pattern and the warning activation timing differ depending on
the setting contents.
Refer to the Settings section in the Mazda Connect Owner's Manual.
Speed Limit Sign Alert setting
xOff: The excessive speed warning is not activated.xVisual: The area around the speed limit sign displayed in the display
flashes in
amber, and if the vehicle speed continues to exceed the displayed speed limit
sign, the indication stops
flashing and remains on.
xVisual + Audible: The area around the speed limit sign displayed in the display
flashes in amber and the warning sound is activated at the same time. If the
vehicle speed continues to exceed the displayed speed limit sign, the indication
When Driving
i-ACTIVSENSE
4-116

1. “Time for a Break” message is
displayed
▼Cancelling Driver Attention Alert
(DAA)
The DAA can be set to not activate.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Driver Monitoring (DM)*
▼Driver Monitoring (DM)
The DM is a system which detects
driver fatigue and sleepiness, and
encourages the driver to take a rest.
While driving the vehicle at about 5
km/h (3 mph) or faster, the DM
detects changes in the driver's facial
features using the driver monitoring
camera. The system then estimates the
amount of accumulated fatigue and
sleepiness of the driver and encourages
the driver to take a rest using a warning
indication in the instrument cluster and
a warning sound.
Two types of warning indication
patterns are set for notifying the driver
based on the estimated amount of
accumulated fatigue and sleepiness of
the driver.
xFatigue and sleepiness are detected:
Warning pattern (caution)
xMuch more fatigue and sleepiness
are detected: Warning pattern
(warning)
When Driving
i-ACTIVSENSE
*Some models.4-121

WARNING
Do not rely completely on the DM
and always drive carefully:
The DM is a system which detects
driver fatigue and sleepiness, and
encourages the driver to take a rest.
This is not designed to prevent driver
fatigue and sleepiness, and
over-reliance on the system could lead
to an accident. Drive carefully and turn
the steering wheel appropriately.
In addition, the system may not be
able to detect driver fatigue and
sleepiness correctly depending on the
traffic and driving conditions. The
driver must take
sufficient rest in order
to drive safely.
Operation conditions
The DM begins monitoring after 20
minutes have passed since the driver
began driving the vehicle and when
the vehicle speed is about 5 km/h (3
mph) or faster.
NOTE
xIf the vehicle speed decreases to less
than about 5 km/h (3 mph) while
the DM is monitoring, the DM stops
monitoring for 6 minutes even if the
vehicle speed returns to about 5
km/h (3 mph) or faster.
xIf the driver monitoring camera does
not recognise the driver correctly, the
DM may not monitor correctly.
Refer to Driver Monitoring Camera
on page 4-226.
xAfter the DM has displayed the
first
message encouraging the driver to
take a rest, it does not display it
again during the following periods.
xAfter displaying the warning
pattern (caution), the next warning
pattern (caution) is not displayed
until 45 minutes have passed.
xAfter displaying the warning
pattern (warning), the next
warning pattern (warning) is not
displayed until 15 minutes have
passed.
xAfter displaying the warning
pattern (warning), the next
warning pattern (caution) is not
displayed until 45 minutes have
passed.
▼Driver Monitoring (DM) Display
When the Driver Monitoring (DM)
detects driver fatigue or sleepiness, it
activates the warning sound and
displays an alert in the instrument
cluster.
Warning pattern (caution) (white)
1. “Time for a Break” message is
displayed

When Driving
i-ACTIVSENSE
4-122

▼Adjustable Speed Limiter (ASL) Display
The setting status of the ASL is displayed in the active driving display or the display in
the instrument cluster.
StatusIndication on
multi-informa-
tion display/
active driving
displayExplanation
Stand-by dis-
play
Displays when the speed limiter switch is operated and the system
is turned on.
Turns off when the system is turned off.
Setting display
Displays when the SET- or SET+ switch is operated and the speed is
set.
Cancel display
Displays when any of the following operations is done and the sys-
tem is temporarily cancelled.
xCANCEL switch is operatedxAccelerator pedal is strongly depressed
Warning display
If the vehicle speed exceeds the set speed by about 5 km/h (3
mph) or more, the ASL display
flashes.
The display flashes until the vehicle speed decreases to the set
speed or less.
A warning beep is activated at the same time as the warning dis-
play.
Refer to Speed Limiter Warning Beep on page 7-72.
▼Activation/Deactivation
NOTE
When the ignition is switched
off, the
system status before it was turned
off is
maintained.
For example, if the ignition is switched
off while the ASL is operating , the
system will be operable when the
ignition is switched ON the next time.
Activation
Press the LIM switch to activation the
system. The ASL screen is displayed,
and the ASL standby indication
displays in white.
Deactivation
Press the LIM switch again to
deactivation the system. The ASL
screen is no longer displayed and the
ASL indication does not display.
When Driving
i-ACTIVSENSE
4-168

▼Setting the System
WARNING
Always verify the safety of the
surrounding area when setting the
ASL:
If the speed is set lower than the
current vehicle speed, the vehicle
speed is decreased to the set speed.
Verify the safety of the surrounding
area and keep a safer distance
between vehicles ahead and behind
you.
1. Press the LIM switch to turn the
system on.
2. Press the RES switch up (SET+) or
down (SET-) to set the speed.
When the current vehicle speed is
30 km/h (19 mph) or more, the
speed is set to the current vehicle
speed. When the current vehicle
speed is less than 30 km/h (19
mph), the speed is set to 30 km/h
(19 mph).
3. To increase the set speed, press the
RES switch up (SET+) continuously.
The set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES switch up (SET
+) momentary. For example, the set
speed increases about 4 km/h (4
mph) by pressing the RES switch up
(SET+) 4 times.
4. To decrease the set speed, press the
RES down
(SET-) continuously. The
set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES down
(SET-)
momentary. For example, the set
speed decreases about 4 km/h (4
mph) by pressing the RES down
(SET-) 4 times.
NOTE
xWhen the vehicle set speed is
displayed in the instrument cluster,
press the RES switch to set the
displayed vehicle speed.
xThe system is temporarily cancelled
when the vehicle is accelerated by
depressing the accelerator pedal
strongly, however, it resumes when
the vehicle speed decreases to the
set speed or less.
xThe vehicle speed may exceed the
set speed on a down slope.
xIn the following cases, the system
cannot be set.
xAny door is open.xThe driver's seat belt is unfastened.
▼Temporarily Cancelling the System
The system is temporarily cancelled
(stand-by status) when any of the
following operations is done while the
ASL is displayed.
xCANCEL switch is pressedxAccelerator pedal is strongly
depressed
xAny door is openedxThe driver’s seat belt is unfastened
Press the RES switch to resume the
operation at the previous set speed.
The ASL display remains displayed.
NOTE
xThe set speed can be set by pressing
the RES switch up (SET+) or down
(SET-) while the system is in stand-by
status.
xThe ASL is not cancelled by
depressing the brake pedal.
When Driving
i-ACTIVSENSE
4-169