2019 MAZDA MODEL CX-30 instrument cluster

▼Intelligent Speed Assistance (ISA) Display
The setting status of the ISA is displayed in the active driving display or the display in
the instrument cluster.
StatusIndication on
multi-informa-
tion display/
active driving
displayExplanation
Stand-by dis-
play
Displays when the speed limiter switch is operated and the system
is turned on.
Turns off when the system is turned off.
Setting display
Displays when the RES switch up (SET+) or down (SET-) is operated
(while the ISA set indication is displayed), and the speed is set.
Cancel display
Displays when any of the following operations is done and the sys-
tem is temporarily cancelled.
xCANCEL switch is operatedxAccelerator pedal is strongly depressedxAny door is openedxThe driver’s seat belt is unfastened
Warning display
If the vehicle speed exceeds the set speed by about 5 km/h (3
mph) or more, the ISA display
flashes.
The display flashes until the vehicle speed decreases to the set
speed or less.
A warning beep is activated at the same time as the warning dis-
play.
Refer to Speed Limiter Warning Beep on page 7-72.
▼Activation/Deactivation
NOTE
When the ignition is switched
off, the
system status before it was turned
off is
maintained.
For example, if the ignition is switched
off while the ISA is operating, the
system will be operable when the
ignition is switched ON the next time.
Activation
Press the LIM switch to activation the
system. The ISA screen is displayed,
and the ISA standby indication displays
in white.
Deactivation
Press the LIM switch again to
deactivation the system. The ISA screen
is no longer displayed and the ISA
indication does not display.
When Driving
i-ACTIVSENSE
4-172

▼Setting the System
WARNING
Always verify the safety of the
surrounding area when setting the
ISA:
If the speed is set lower than the
current vehicle speed, the vehicle
speed is decreased to the set speed.
Verify the safety of the surrounding
area and keep a safer distance
between vehicles ahead and behind
you.
NOTE
xThe system is temporarily cancelled
when the vehicle is accelerated by
depressing the accelerator pedal
strongly, however, it resumes when
the vehicle speed decreases to the
set speed or less.
xThe vehicle speed may exceed the
set speed on a down slope.
xIn the following cases, the system
cannot be set.
xAny door is open.xThe driver's seat belt is unfastened.xThe ISA setting can be changed to
MANUAL, or OFF*1.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
*1 When OFF is selected, the
Adjustable Speed Limiter (ASL) is
set.
Refer to Adjustable Speed Limiter
(ASL) on page 4-166.
How to set the speed limit using the
RES switch
1. Press the LIM switch to turn the
system on.
2. Press the RES switch up (SET+) or
down (SET-) to set the speed.
When the current vehicle speed is
30 km/h (19 mph) or more, the
speed is set to the current vehicle
speed. When the current vehicle
speed is less than 30 km/h (19
mph), the speed is set to 30 km/h
(19 mph).
3. To increase the set speed, press the
RES switch up (SET+) continuously.
The set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES switch up (SET
+) momentary. For example, the set
speed increases about 4 km/h (4
mph) by pressing the RES switch up
(SET+) switch 4 times.
4. To decrease the set speed, press the
RES switch down (SET-)
continuously. The set speed can be
adjusted in 10 km/h (5 mph)
increments. The set speed can also
be adjusted in about 1 km/h (1
mph) increments by pressing the
RES switch down (SET-)
momentary. For example, the set
speed decreases about 4 km/h (4
mph) by pressing the RES switch
down (SET-) 4 times.
NOTE
xWhen the vehicle set speed is
displayed in the active driving
display/instrument cluster and speed
limit sign is not displayed, press the
RES switch to set the displayed
vehicle speed.
Manually setting the vehicle speed
limit from a speed limit sign
1. Press the LIM switch to turn the
system on.
2. Press the RES switch while the ISA
set indication is displayed on the
active driving display/instrument
When Driving
i-ACTIVSENSE
4-173

xMultiple pedestrians are walking ,
or there are groups of people.
xA pedestrian is close to a separate
object.
xA pedestrian is crouching , lying , or
slouching.
xA pedestrian suddenly jumps into
the road right in front of the
vehicle.
xA pedestrian opens an umbrella, or
is carrying large baggage or
articles.
xA pedestrian is in a dark location
such as during the night, or blends
into the background by wearing
clothes matching the background
colour.
Front Radar Sensor*
▼Front Radar Sensor
Your vehicle is equipped with a front
radar sensor.
The following systems also use the
front radar sensor.
xDistance & Speed Alert (DSA)xMazda Radar Cruise Control
(MRCC)
xMazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)
xCruising & Traffic Support (CTS)xSmart Brake Support (SBS)
The front radar sensor functions by
detecting the radio waves reflected off
a vehicle ahead or an obstruction sent
from the radar sensor.
The front radar sensor is mounted
behind the front emblem.
1. Front radar sensor

If “Safety and Driver Support Systems
Temporarily Disabled. Front Radar
Obscured. Drive Safely” is displayed on
the multi-information display of the
instrument cluster, clean the area
around the front radar sensor.
CAUTION
Heed the following precautions to
assure correct operation of each
system.
When Driving
i-ACTIVSENSE
4-220*Some models.

Cruise Set Indication (Green)
The indication turns on (green) when a
cruising speed has been set.
▼Activation/Deactivation
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as the
cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the
ignition is switched OFF with the cruise
control system operable, the system
will be operable when the ignition is
switched ON the next time.
Activation
To activate the system, press the cruise
switch. The cruise standby indication
(white) turns on.
Deactivation
To deactivate the system, press the
cruise switch again.
The cruise standby indication (white)
turns
off.
▼To Set Speed
1. Activate the cruise control system
by pressing the cruise switch. The
cruise standby indication (white)
turns on.
2. Accelerate to the desired speed,
which must be more than 25 km/h
(16 mph).
3. Adjust the system to the desired
vehicle speed using the accelerator
pedal. Press the RES switch up (SET
+) or down (SET-) to start cruise
control. The cruise control
indication (green) in the instrument
cluster turns on at the same time.
Quickly release the switch when the
cruise control indication (green)
turns on.
NOTE
xIf the RES switch is operated up (SET
+) or down (SET-) while the vehicle
speed is between 25 km/h (16 mph)
and 30 km/h (19 mph), the set
speed is set to 30 km/h (19 mph).
xThe cruise control speed setting
cannot be performed under the
following conditions:
xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe brake pedal is depressed.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xOn a steep grade, the vehicle may
momentarily slow down while
ascending or speed up while
descending.
xThe cruise control will cancel if the
vehicle speed decreases below 20
km/h (12 mph) when the cruise
control is activated, such as when
climbing a steep grade.
When Driving
Cruise Control
4-229

The vehicle speed preset using the
cruise control is displayed in the
instrument cluster and the active
driving display (vehicles with active
driving display).
Instrument cluster (Basic display)
Instrument cluster (i-ACTIVSENSE
display)
Active driving display
▼Changing the Set Vehicle Speed
Follow either of these procedures.
To increase/decrease speed using
cruise control switch
When the RES switch is pressed up
(SET+), the vehicle accelerates and
when the RES switch is pressed down
(SET-), it decelerates.
xPress and release immediately: 1
km/h (1 mph)
xPress and hold: 10 km/h (5 mph)
NOTE
Even after releasing the RES switch, the
cruise control accelerates/decelerates
continuously until the set speed
displayed in the instrument cluster and
on the active driving display is reached.
If you want to stop accelerating/
decelerating, change the set speed or
cancel the system (such as by
depressing the brake pedal).
To increase speed using accelerator
pedal
Depress the accelerator pedal and
press the RES switch up (SET+) or
down (SET-) at the desired speed. If
the switch is not operated, the system
returns to the set speed after you
release your foot from the accelerator
pedal.
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere
with or change the set speed. Take
your foot off the accelerator to return
to the set speed.
▼To Resume Cruising Speed at More
Than 30 km/h (19 mph)
If the cruise control system is
temporarily cancelled (such as by
applying the brake pedal) and the
system is still activated, the most
recent set speed will automatically
resume when the RES switch is
pressed.
If vehicle speed is below 30 km/h (19
mph), increase the vehicle speed up to
When Driving
Cruise Control
4-230

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Vent Operation
▼Adjusting the Vents
Directing airflow
To adjust the direction of
airflow, move
the adjustment knob.
NOTE
xWhen using the air conditioner
under humid ambient temperature
conditions, the system may blow fog
from the vents. This is not a sign of
trouble but a result of humid air
being suddenly cooled.
xThe air vents can be fully opened and
closed by operating the knob/dial.
Driver's Side Vents
Air vent open/close
1. Knob
2. Open
3. Close
NOTE
The figure indicates the air vent on the
left side of the instrument cluster. The
operation direction for the air vent on
the right side of the instrument cluster
is symmetrical with the air vent on the
left side.

Airflow direction adjustment
1. Knob

Passenger's Side Vents
Air vent open/close
1. Knob
2. Open
3. Close

Interior Features
Air-Conditioning System
5-3

xWhenever the engine oil is replaced, the vehicles engine control unit needs to be
reset as soon as possible. Otherwise the wrench indicator light or engine oil
warning light may turn on. To reset the engine control unit, consult an expert
repairer (we recommend an Authorised Mazda Repairer) or refer to the vehicle
status monitor section in the Mazda Connect Owner's Manual.
▼Inspecting Engine Oil Level
NOTE
xIf the engine oil level warning
indication/warning light turns on,
add 1 L (0.3 US gal, 0.2 Imp gal) of
engine oil.
x(SKYACTIV-D 1.8)
If “Excessive Oil Level. Have the
Vehicle Inspected” is displayed on
the multi-information display in the
instrument cluster, have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5
minutes for the oil to return to the
sump.
4.(SKYACTIV-X 2.0)
Open the engine cover (page
6-19).
5. Pull out the dipstick, wipe it clean,
and reinsert it fully.
SKYACTIV-G 2.0 and SKYACTIV-G
2.5

1. MAX
2. OK
3. MIN

SKYACTIV-X 2.0

1. MAX
2. OK
Maintenance and Care
Owner Maintenance
6-27