2019 MAZDA MODEL CX-30 instrument cluster

NOTE
xIf the Electric Parking Brake (EPB)
switch is pulled while the
AUTOHOLD is operating , the
parking brake is applied and the
AUTOHOLD is released. In addition,
if the parking brake is released under
this condition, the AUTOHOLD
operates to hold the brakes.
xUnder the following conditions, the
parking brake is automatically
applied and the AUTOHOLD is
released. The AUTOHOLD is
re-enabled when the conditions
before the AUTOHOLD is released
are restored.
xThe driver’s seat belt is unfastened.xThe driver’s door is opened.xWhen about 10 minutes or longer
have passed since the AUTOHOLD
operation started, the parking brake
is automatically applied. Because the
AUTOHOLD is restored when
releasing the parking brake, the hold
on the brakes by AUTOHOLD
function resumes.
x(Manual transmission vehicle)
When starting to drive the vehicle
forward or in reverse on a down
slope, depress the clutch pedal and
shift the shift lever to the appropriate
position for driving in the desired
direction, and then depress the
accelerator pedal to release the
AUTOHOLD.
xThe AUTOHOLD can be cancelled
forcibly by fully depressing the
accelerator pedal for 1 second or
longer while the AUTOHOLD is
operating. Forcibly cancel the
AUTOHOLD only when the
AUTOHOLD cannot be cancelled
due to a system malfunction or it is
necessary to cancel the AUTOHOLD
in an emergency.
▼AUTOHOLD System is Turned Off
Depress the brake pedal and press the
AUTOHOLD switch. The AUTOHOLD
is turned off and the AUTOHOLD
standby indicator light turns off.
1. AUTOHOLD standby indicator light
NOTE
xWhen the brakes are not held such
as while driving the vehicle, the
AUTOHOLD can be turned off only
by pressing the AUTOHOLD switch.
xIf the AUTOHOLD switch is pressed
without depressing the brake pedal
while AUTOHOLD is operating
(AUTOHOLD active indicator light in
instrument cluster is turned on), the
message “Depress Brake Pedal and
Operate Switch to Release” is
indicated on the multi-information
display to notify the driver to depress
the brake pedal.
xIf any of the following conditions
occurs while the AUTOHOLD
function is operating (AUTOHOLD
active indicator light is turned on),
the parking brake is applied
automatically and the AUTOHOLD
function turns off. For the Electric
Parking Brake (EPB) operation, refer
to the Electric Parking Brake (EPB) on
page 4-70.
xThe ignition is switched OFF.
When Driving
Brake
4-77

▼TCS OFF Indicator Light*
This indicator light stays on for a few
seconds when the ignition is switched
ON.
It also illuminates when the TCS OFF
switch is pressed and TCS is switched
off.
Refer to TCS OFF Switch on page
4-82.

If the light remains illuminated and the
TCS is not switched off, take your
vehicle to an expert repairer (we
recommend an Authorised Mazda
Repairer). The DSC may have a
malfunction.
▼TCS OFF Switch*
Press the TCS OFF switch to turn off the
TCS. The TCS OFF indicator light in the
instrument cluster and the TCS OFF
switch indicator light will illuminate.
1. TCS OFF switch indicator light

Press the switch again to turn the TCS
back on. The TCS OFF indicator light
and the TCS OFF switch indicator light
will turn
off.
NOTE
xWhen TCS is on and you attempt to
free the vehicle when it is stuck, or
drive it out of freshly fallen snow, the
TCS (part of the DSC system) will
activate. Depressing the accelerator
will not increase engine power and
freeing the vehicle may be difficult.
When this happens, turn off the TCS.
xIf the TCS is off when the engine is
turned
off, it automatically activates
when the ignition is switched ON.
xLeaving the TCS on will provide the
best traction.
xIf the TCS OFF switch is pressed and
held for 10 seconds or more, the
TCS OFF switch malfunction
detection function operates and the
TCS system activates automatically.
The TCS OFF indicator light turns off
while the TCS system is operative.
When Driving
ABS/TCS/DSC/Off-Road Traction Assist
4-82*Some models.

Off-Road Traction Assist*
▼Off-Road Traction Assist
When the vehicle tyres become
embedded in mud, sand, or deep
snow, the
Off-Road Traction Assist
functions to prevent drive-wheel
spinning and to assist in freeing tyres
that are stuck.
This is not a function made for
off-road
driving. Do not drive over rough rocky
roads and river beds.
WARNING
Do not rely completely on the
Off-Road Traction Assist.
The
Off-Road Traction Assist has
limitations. Always drive the vehicle
safely according to the road
conditions. Do not drive the vehicle
recklessly, otherwise it may result in an
accident. In addition, do not drive the
vehicle under the following conditions
while the
Off-Road Traction Assist is
operating. Otherwise, it could
negatively affect the drivetrain parts
which could result in an accident.
¾Vehicle is driven on paved roads.
¾Temporary spare tyre of a different
specified size is used.
¾Tyre chains are used.
Do not drive the vehicle
off road.
The Off-Road Traction Assist is a
function to assist in freeing tyres that
are stuck. Also, avoid continuous use
of this function on muddy, sandy,
deep-snowy, or uneven roads.
If this function is used continuously,
the AWD warning light may
flash.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
NOTE
The vehicle may vibrate or you might
hear an operation sound while the
Off-Road Traction Assist is operating or
is operational, however, this does not
indicate a problem.
▼Off-Road Traction Assist Indicator
Light
xWhen the ignition is switched ON,
the indicator light turns on and then
turns off after a few seconds.
xWhen pressing the Off-Road Traction
Assist switch to operate the Off-Road
Traction Assist, the indicator light
turns on.
xA problem in the system might be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe indicator light does not turn on
when the ignition is switched ON
or it remains on.
xThe indicator light turns on even
though the Off-Road Traction
Assist was not operated.
▼Off-Road Traction Assist Switch
When the switch is pressed after
stopping the vehicle, the
Off-Road
Traction Assist becomes operational.
The Off-Road Traction Assist indicator
light in the instrument cluster and the
When Driving
ABS/TCS/DSC/Off-Road Traction Assist
4-84*Some models.

▼Select Mode Indicator Light
When the sport mode is selected, the
select mode indicator light turns on in
the instrument cluster.
1. Select mode indicator light
NOTE
If the drive selection cannot be
switched to sport mode, the select
mode indicator light
flashes to notify
the driver.
When Driving
Drive Selection
4-91

NOTE
For example, even when the Blind Spot
Monitoring (BSM) is operating
normally, if the Lane Departure
Warning System (LDWS) has a
problem, the i-ACTIVSENSE status
symbol (warning/risk avoidance
support system) (white) is displayed.
i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green)
System activated status
If any one of the systems is activated,
the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green) is displayed.
NOTE
Even if the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green) is displayed, systems
which do not meet the operation
conditions will not operate.
i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (amber)
System warning status
If any system warning is activated, the
i-ACTIVSENSE status symbol (warning/
risk avoidance support system)
(amber) is displayed.
i-ACTIVSENSE OFF symbol (warning/
risk avoidance support system)
System OFF status
If all the systems are cancelled using
the personalisation features or the
i-ACTIVSENSE switch, the
i-ACTIVSENSE OFF symbol (Warning/
risk avoidance support system) is
displayed.
▼i-ACTIVSENSE Switch
When the i-ACTIVSENSE switch is
pressed, the following systems are
cancelled and the i-ACTIVSENSE OFF
symbol (Warning/risk avoidance
support system) in the instrument
cluster is displayed.
xLane Departure Warning System
(LDWS)
xBlind Spot Monitoring (BSM)xDistance & Speed Alert (DSA)xFront Cross Traffic Alert (FCTA)xRear Cross Traffic Alert (RCTA)xLane-keep Assist System (LAS)
When Driving
i-ACTIVSENSE
4-97

xWhen there is insufficient darkness
such as at dawn or dusk.
xWhen the luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xWhen visibility is reduced due to a
vehicle in front of you spraying water
from its tyres onto your windscreen.
▼To Operate the System
The HBC operates to switch the
headlights automatically between high
and low beams after the ignition is
switched ON and the headlight switch
is in the AUTO and low beam position.
The HBC determines that it is dark
based on the brightness of the
surrounding area. At the same time,
the HBC indicator light (green) in the
instrument cluster illuminates.

NOTE
Operation of the HBC function can be
disabled.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Manual Switching
Switching to low beams
Switch the headlight switch to the
position, or press the high beam
control switch.
The HBC indicator light (green) turns
off.
1. High beam control switch

If the HBC is turned off using the high
beam control switch, press the high
beam control switch again to turn the
HBC back on.
Switching to high beams
Shift the lever to the high beam
position.
The HBC indicator light (green) turns
off and the headlight high-beam
indicator light is illuminated.
When Driving
i-ACTIVSENSE
4-100

xWhen there are other sources of light
in the area such as street lamps,
illuminated signboards, and traffic
signals.
xWhen there are reflective objects in
the surrounding area such as
reflective plates and signs.
xWhen visibility is reduced under rain,
snow and foggy conditions.
xWhen driving on roads with sharp
curves or undulations.
xWhen the headlights/rear lamps of
vehicles ahead or in the opposite
lane are dim or not illuminated.
xWhen there is insufficient darkness
such as at dawn or dusk.
xWhen the luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xWhen visibility is reduced due to a
vehicle ahead spraying water from its
tyres onto your windscreen.
▼To Operate the System
The ALH operates to control Glare-Free
High Beam, Wide-Range Low Beam
and Highway Mode automatically after
the ignition is switched ON and the
headlight switch is in the
and
low beam position.
The ALH determines that it is dark
based on the brightness of the
surrounding area. At the same time,
the ALH indicator light (green) in the
instrument cluster illuminates.
NOTE
Operation of the ALH function can be
disabled.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Manual Switching
Switching to low beams
Switch the headlight switch to the
position, or press the ALH switch.
The ALH indicator light (green) turns
off.
1. ALH switch

If the ALH is turned off using the ALH
switch, press the ALH switch again to
turn the ALH back on.
Switching to high beams
Shift the lever to the high beam
position.
The ALH indicator light (green) turns
off and the headlight high-beam
indicator light is illuminated.
When Driving
i-ACTIVSENSE
4-102

2. Detection areas
WARNING
Always check the surrounding area
visually before making an actual lane
change:
The system is only designed to assist
you in checking for vehicles at your rear
when making a lane change. Due to
certain limitations with the operation
of this system, the BSM warning
indicator light, the warning sound and
the warning screen indicator display
may not activate or they might be
delayed even though a vehicle is in an
adjacent driving lane. Always make it
your responsibility as a driver to check
the rear.
NOTE
xThe BSM will operate when all of the
following conditions are met:
xThe ignition is switched ON.xThe i-ACTIVSENSE warning
indication/warning light in the
instrument cluster is turned off.
xThe vehicle speed is about 30
km/h (19 mph) or faster.
xThe BSM will not operate under the
following circumstances.
xThe vehicle speed falls below
about 25 km/h (15 mph) even
though the i-ACTIVSENSE warning
indication/warning light is turned
off.
xThe shift lever (manual
transmission)/selector lever
(automatic transmission) is shifted
to reverse (R) and the vehicle is
reversing.
xThe turning radius is small (making
a sharp turn, turning at
intersections).
xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the BSM warning
indicator lights is detected.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
Remove any snow, ice or mud on
the rear bumper.
xDriving on snow-covered roads for
long periods.
xThe temperature near the rear side
radar sensor becomes extremely
hot due to driving for long periods
on slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
xThe rear bumper around the rear
side radar sensor is deformed.
xRadio wave interference from a
radar sensor equipped on a nearby
vehicle.
xThe approaching vehicle is any of
the following shapes.
a) The size of the vehicle body is
extremely small.
b) The vehicle height is extremely
low or high.
c) A special type of vehicle with a
complex shape.
When Driving
i-ACTIVSENSE
4-107